Korg pa 900 User Manual page 366

Professional arranger
Hide thumbs Also See for pa 900:
Table of Contents

Advertisement

Effects
362
EQ and Filters (EQ/Filter)
Dry, 1:99...99:1,
Wet/Dry
Wet
j
Src
Off...Tempo
Amt
–100...+100
a: Type
This parameter selects a combination of center frequencies for
each band. The center frequency of each band is shown in the
right of the screen.
You can configure a 21-Band Graphic EQ ranging from 80 Hz to
18 kHz if you route three Graphic 7-Band EQ effects in series,
with a setting of 7:Low, 9:Mid, and 11:High for each EQ.
8: St.Exciter/Enhncr
(Stereo Exciter/Enhancer)
This effect is a combination of the Exciter, which adds a punch
to the sound and the Enhancer, which adds spread and presence.
Stereo In - Stereo Out
Left
LEQ
HEQ
Exciter
EQ Trim
EQ Trim
Exciter
Right
D
-mod
Exciter Blend
–100...+100
a
Src
Off...Tempo
Amt
–100...+100
Emphasis Freq 0...70
b
Src
Off...Tempo
Amt
–70...+70
Enhancer
c
0.0...50.0
Delay L [msec]
Enhancer
d
0.0...50.0
Delay R [msec]
Enhancer
0...100
Depth
e
Src
Off...Tempo
Amt
–100...+100
f
EQ Trim
0...100
Low,
Pre LEQ Fc
Mid-Low
g
High,
Pre HEQ Fc
Mid-High
Pre LEQ Gain
–15.0...+15.0
[dB]
h
Pre HEQ Gain
–15.0...+15.0
[dB]
Dry, 1:99...99:1,
Wet/Dry
Wet
i
Src
Off...Tempo
Amt
–100...+100
a: Exciter Blend
This parameter sets the depth (intensity) of the Exciter effect.
Positive values give a frequency pattern (to be emphasized) dif-
ferent from negative values.
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 357
Amount of modulation source
FX Amt
Delay
Depth
Delay
Enhancer
FX Amt
Sets the intensity (depth) of the
Exciter effect
Selects the modulation source of the
Exciter intensity
Sets the modulation amount of the
Exciter intensity
Sets the frequency to be empha-
sized
Selects the modulation source of the
frequency to be emphasized
Sets the amount of modulation of the
frequency to be emphasized
Sets the delay time for the Enhancer
left channel
Sets the delay time for the Enhancer
right channel
Sets the determines to what degree
the Enhancer effect is applied
Selects the modulation source of the
Enhancer width
Sets the modulation amount of the
Enhancer width
Sets the 2-band EQ input level
Selects the cutoff frequency (low or
mid-low) of the low-range equalizer
Selects the cutoff frequency (high or
mid-high) of the high-range
equalizer
Gain of the Lo EQ
Gain of the High EQ
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 357
Amount of modulation source
b: Emphasis Freq
This parameter sets the frequency to be emphasized. Higher val-
ues will emphasize lower frequencies.
c: Enhancer Delay L [msec]
d: Enhancer Delay R [msec]
These parameters set the delay time for the Enhancer left and
right channel. Specifying a slightly different delay time for the
left and right channel will add a stereo image, depth, and width
to the sound.
9: Stereo Isolator
This is a stereo effect that separates the input signal into low,
mid, and high-frequency bands, and controls the volume of each
band independently. For example you can separately boost or cut
the kick, snare, and hi-hat sounds from a drum signal in real-
time.
Stereo In - Stereo Out
Left
Low
Mid
Trim
High
Isolator
Low
Mid
Trim
High
Right
D
-mod
D
-mod
D
-mod
a
Trim
0...100
b Low/Mid [Hz]
100...500
c
Mid/High [Hz]
2000...6000
–Inf,
Low Gain [dB]
–59...+12
d
Src
Off...Tempo
Amt
–72...+72
–Inf,
Mid Gain [dB]
–59...+12
e
Src
Off...Tempo
Amt
–72...+72
–Inf,
High Gain [dB]
–59...+12
f
Src
Off...Tempo
Amt
–72...+72
Dry, 1:99...99:1,
Wet/Dry
Wet
g
Src
Off...Tempo
Amt
–100...+100
FX Amt
FX Amt
Sets the input level
Sets the frequency at which the low
and mid bands are divided
Sets the frequency at which the mid
and high bands are divided
Sets the low-frequency gain
Selects the source that will
modulate low-frequency gain
Sets the amount by which the low-
frequency gain will be modulated
Sets the mid-frequency gain
Selects the modulation source for
mid-frequency gain
Sets the amount by which the mid-
frequency gain will be modulated
Sets the high-frequency gain
Selects the modulation source for
high-frequency gain
Sets the amount by which the high-
frequency gain will be modulated
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 357
Amount of modulation source

Advertisement

Table of Contents
loading

Table of Contents