Korg pa 900 User Manual page 410

Professional arranger
Hide thumbs Also See for pa 900:
Table of Contents

Advertisement

Effects
406
Mono-Mono Serial (Mono-Mono)
86: Comp - P4EQ
(Compressor - Parametric 4-Band EQ)
This effect combines a mono compressor and a four-band para-
metric equalizer. You can change the order of the effects.
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
Left
Compressor
+
Comp
Output Level
Right
Envelope - Control
COMPRESSOR
[C]
a
1...100
Sensitivity
[C]Attack
1...100
b
Output Level
0...100
P4EQ
c
[E]Trim
0...100
[E]B1 Cutoff
20...1.00k
[Hz]
d
Q
0.5...10.0
Gain [dB]
–18...+18
[E]B2 Cutoff
50...5.00k
[Hz]
e
Q
0.5...10.0
Gain [dB]
–18...+18
[E]B3 Cutoff
300...10.00k
[Hz]
f
Q
0.5...10.0
Gain [dB]
–18...+18
[E]B4 Cutoff
500...20.00k
[Hz]
g
Q
0.5...10.0
Gain [dB]
–18...+18
Comp P4EQ,
h Routing
P4EQ Comp
Dry, 1:99...99:1,
Wet/Dry
Wet
i
Src
Off...Tempo
Amt
–100...+100
FX Amt
Routing
Parametric 4Band EQ
Trim
FX Amt
Sets the sensitivity
Sets the attack level
Sets the compressor output level
Sets the parametric EQ input level
Sets the center frequency of Band 1
Sets the bandwidth of Band 1
Sets the gain of Band 1
Sets the center frequency of Band 2
Sets the bandwidth of Band 2
Sets the gain of Band 2
Sets the center frequency of Band 3
Sets the bandwidth of Band 3
Sets the gain of Band 3
Sets the center frequency of Band 4
Sets the bandwidth of Band 4
Sets the gain of Band 4
Switches the order of the
compressor and parametric EQ
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 357
Amount of modulation source
87: Comp - Cho/Flng
(Compressor - Chorus/Flanger)
This effect combines a mono compressor and a chorus/flanger.
You can change the order of the effects.
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
Left
Compressor
EQ Trim
LEQ HEQ
+
Comp
Output Level
Right
Envelope - Control
COMPRESSOR
[C]
a
1...100
Sensitivity
[C]Attack
1...100
b
Output Level
0...100
c
[C]EQ Trim
0...100
[C]Pre LEQ
–15...+15
Gain [dB]
d
Pre HEQ Gain
–15...+15
[dB]
CHORUS/FLANGER
[F]LFO
0.02...20.00
Frequency [Hz]
e
LFO Waveform Triangle, Sine
[F]Delay Time
0.0...1350.0
[msec]
f
Depth
0...100
Feedback
–100...+100
-Wet, -
[F]Cho/Flng
1:99...Dry...99:1
Wet/Dry
, Wet
g
Src
Off...Tempo
Amt
–100...+100
[F]Output
Normal,
h
Mode
Wet Invert
Comp
i
Routing
Flanger,
Flanger Comp
Dry, 1:99...99:1,
Wet/Dry
Wet
j
Src
Off...Tempo
Amt
–100...+100
h: [F]Output Mode
i: Routing
When Wet Invert is selected, the right channel phase of the cho-
rus/flanger effect sound is inverted. This creates pseudo-stereo
effects and adds spread.
However, if a mono-input type effect is connected after this
effect, the left and right sounds may cancel each other, eliminat-
ing the chorus/flanger effects.
When "Routing" is set to Flanger→ Comp, "[F]Output Mode"
will be set to Normal.
FX Amt
Routing
Chorus/Flanger
Chorus/Flanger
Normal
+
Output Mode
Wet Invert
Feedback
Cho/Flng FX Amt
FX Amt
LFO: Tri / Sine
Sets the sensitivity
Sets the attack level
Sets the compressor output level
Sets the EQ input level
Sets the gain of Low EQ
Sets the gain of High EQ
Sets the speed of the LFO
Selects the LFO Waveform
Sets the delay time
Sets the depth of LFO modulation
Sets the feedback amount
Sets the effect balance of the
chorus/flanger
,
Selects the Wet/Dry modulation
source for the chorus/flanger
Sets the Wet/Dry modulation
amount for the chorus/flanger
Selects the output mode for the
chorus/flanger
Switches the order of the
compressor and chorus/flanger
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 357
Amount of modulation source

Advertisement

Table of Contents
loading

Table of Contents