Korg pa 900 User Manual page 426

Effects
422
Double Size
115: St. Mic + PreAmp
(Stereo Mic Modeling + PreAmp)
This is a stereo mic and preamp simulator (See "Mic Model+Pre-
Amp (Mic Modeling + PreAmp)" on page 372.). For example
you might use this to simulate micing of a stereo source such as a
rotary speaker.
Stereo In - Stereo Out
Left
Mic Simulation
Mic Simulation
Right
116: Multitap Cho/Delay
(Multitap Chorus/Delay)
This effect has six chorus blocks with different LFO phases. You
can produce a complex stereo image by setting a different delay
time and depth for each block. You can control the delay output
level via a modulation source.
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In -Stereo Out
Left
Feedback
Tap1 Delay
Tap2 Delay
Tap3 Delay
+
Tap4 Delay
Tap5 Delay
Tap6 Delay
Right
0 [degree]
180 [degree]
60 [degree]
240 [degree]
120 [degree]
300 [degree]
LFO: Triangle
D -mod
On/Off Control
LFO Frequency
a 0.02...13.00
[Hz]
Tap1 (000)
0...2000
[msec]
Depth 0...30
b
Always On,
Always Off,
Status
On Off (Dm),
Off On (Dm)
Tap2 (180)
0...2000
[msec]
Depth 0...30
c
Always On,
Always Off,
Status
On Off (Dm),
Off On (Dm)
Tap3 (060)
0...2000
[msec]
Depth 0...30
d
Always On,
Always Off,
Status
On Off (Dm),
Off On (Dm)
Tap4 (240)
0...2000
[msec]
Depth 0...30
e
Always On,
Always Off,
Status
On Off (Dm),
Off On (Dm)
Tap5 (120)
0...2000
[msec]
Depth 0...30
f
Always On,
Always Off,
Status
On Off (Dm),
Off On (Dm)
FX Amt
Tube Pre Amp
Output Level
Tube Pre Amp
FX Amt
FX Amt
FX Amt
Panning Preset
Sets the speed of the LFO
Sets the Tap1 (LFO phase=0
degrees) delay time
Sets the Tap1 chorus depth
Selects on, off, or modulation source
for the control of Tap1 output
Sets the Tap2 (LFO phase=180
degrees) delay time
Sets the Tap2 chorus depth
Selects on, off, or modulation source
for the control of Tap2 output
Sets the Tap3 (LFO phase=60
degrees) delay time
Sets the Tap3 chorus depth
Selects on, off, or modulation source
for the control of Tap3 output
Sets the Tap4 (LFO phase=240
degrees) delay time
Sets the Tap4 chorus depth
Selects on, off, or modulation source
for the control of Tap4 output
Sets the Tap5 (LFO phase=120
degrees) delay time
Sets the Tap5 chorus depth
Selects on, off, or modulation source
for the control of Tap5 output
Tap6 (300)
0...2000
[msec]
Depth 0...30
g
Always On,
Always Off,
Status
On Off (Dm),
Off On (Dm)
1 : L 1 2 3 4 5 6 R,
2 : L 135 246 R,
h Panning Preset
3 : L 1 3 5 2 4 6 R,
4 : L 1 4 5 6 3 2 R
Tap1 Feedback –100...+100
Src Off...Tempo
i
Amt –100...+100
Dry, 1:99...99:1,
Wet/Dry
Wet
j
Src Off...Tempo
Amt –100...+100
b, c, d, e, f, g: Status
These parameters set the output status of each Tap.
Always On: Output is always on. (No modulation)
Always Off: Output is always off. (No modulation)
On→ Off (dm): Output level is switched from on to off depend-
ing on the modulation source.
Off→ On (dm): Output level is switched from off to on depend-
ing on the modulation source.
Combining these parameters, you can change from 4-phase cho-
rus to two-tap delay by crossfading them gradually via the mod-
ulation source during a performance.
h: Panning Preset
This parameter selects combinations of stereo images of the tap
outputs.
Sets the Tap1 (LFO phase=300
degrees) delay time
Sets the Tap6 chorus depth
Selects on, off, or modulation source
for the control of Tap6 output
Selects the stereo panning pattern
for each tap
Sets the Tap1 feedback amount
Selects the modulation source for
the Tap output level, feedback
amount, and effect balance
Sets the modulation amount of Tap1
feedback amount
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 357
Amount of modulation source