Related Manuals for IDTECK SRK101
Summary of Contents for IDTECK SRK101
- Page 1 User’s Manual 13.56MHz Contactless Smart Card Reader 13.56MHz Contactless Universal Smart Card Reader Fingerprint-Stored Smart Card ID-Only Reader...
-
Page 2: Table Of Contents
Table of Contents 1. Important Safety Instructions..............3 2. General....................4 3. Features ....................4 4. Identifying Supplied Parts..............5 5. Specification..................6 6. Installation .................... 8 7. Wire Color Table................. 10 8. Output Format ..................10 9. Wire Connection to Access Controller..........13 10. -
Page 3: Important Safety Instructions
1. Important Safety Instructions When using the 13.56MHz [MIFARE] Contactless Smart Card Reader (SRK101) / 13.56MHz Contactless Universal Smart Card Reader (SRK101U) / Fingerprint Stored Smart Card ID Only Reader (SRK101B), basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons. -
Page 4: General
IDTECK SR101 reads the serial number stored on the Philips Mifare™ card (ISO14443 Type A) and transmits the data to the controller in various formats. IDTECK SR101U reads the serial number stored on the ISO14443 Type A/B card and transmits the data to the controller in various formats. -
Page 5: Identifying Supplied Parts
- 26bit Wiegand (default) / RS232, ABA Track II (optional) Output Format - Compatible Controller: iCON100, iTDC, FINGER007SRB, Third Party Controller. - Compatible Reader: SR10B, SR30B, FGR006SRB, FINGER006SRB 4. Identifying Supplied Parts Please unpack and check the contents of the box: SRK101/SRK101U/SRK101B Wall Mount O-Ring User’s Manual (1ea) -
Page 6: Specification
5. Specification Model SRK101 SRK101U SRK101B ISK50 / IMC135: up to 2 inches (5cm) Type A ISC80: up to 4 inches (10cm) Read Range ISC80B: up to 4 Type B inches (10cm) Card Reading Time 30ms Power / Current DC12V / Max. 180mA... - Page 7 ISC80 ISC80B ISK50 IMC135 IHC80 SR10 / Up to 4 SR30 / inches Up to 2 inches (5cm) SRK101 (10cm) SR10B / Up to 4 SR30B / inches Up to 2 inches (5cm) SRK101B (10cm) SR10U / Up to 4...
-
Page 8: Installation
6. Installation 6-1. Make sure the magnet is attached to the magnet guide on the Wall Mount. 6-2. On the last page of this manual, you can find an actual-size template for the Wall Mount. Cut the page out and use it as a guide to help you drill two 6-32 or M3 screw holes and one 1/2" hole. - Page 9 6-5. Installation Considerations 1. When installing a reader on a metal wall The read range may get reduced if the reader is installed on a metal surface. To prevent such a read range reduction, install a Spacer between the metal surface and the reader. 2.
-
Page 10: Wire Color Table
7. Wire Color Table Signal Color Main Power (+12V) Power Ground (GND) Black ABA Track II CP Out Orange Wiegand Data 0 Out / ABA Track II Data Out Green Wiegand Data 1 Out / ABA Track II Clock Out White Buzzer Control In Blue... - Page 11 8-2 4bit and 8bit Burst Output Format (Keypad) 1. Data Format (4bit Burst output format) Keypads Binary Hexa Keypads Binary Hexa 0000 0110 0001 0111 0010 1000 0011 1001 0100 1010 0101 1011 (8bit Burst output format) Keypads Binary Hexa Keypads Binary Hexa...
- Page 12 8-3 RS-232 (Option) Output Format 1. Data Format (Baud Rate : 9600bps) +15V Space (=0) Indeterminate Region Mark (=1) 8 Data Bits -15V 2 Stop Bits Start Bit Data packet corresponding to ASCII character 'A' 2. Data Structure START(0X02H) DATA(8 Char) END (0x03H) (Card Output) START(0X02H)
-
Page 13: Wire Connection To Access Controller
SRK101B Output Format: 26bit Wiegand + RS232 (Card) + 8bit Burst (PIN) - SRK101/SRK101U/SRK101B transmits the card/keypad data to the Access Controller via Wiegand Data1 and RS232(TX) wires. (34/26bit Wiegand, 8bit burst, RS232) 9-2. Wiring for Controlling Red, Green, and Yellow LEDs (Optional) -
Page 14: Operations
10-1. Connector Layout Jumper Setting SRK101 V2.0.0 JP2, JP4 : OFF (Do not change these jumpers by yourself.) 10-2. Output Selection Table 1. Jumper Setting (SRK101/SRK101U/SRK101B) Card Output Format Keypad Output Format 34/26bit Wiegand + RS232 8bit Burst 34/26bit Wiegand + RS232... - Page 15 3. Press the keypad and you’ll hear a beep. Then, the reader will pass the keypad input data on to the controller. 4. In the 34bit Wiegand + RS232 output format (SRK101 or SRK101U), an ID (PIN) is in the range of 0 to 4294967295, without a facility code. In the 26bit Wiegand + RS232 output format (SRK101B), a facility code is within the range of 0 to 255 and an ID (PIN) in the range of 0 to 65535.
-
Page 16: Applendix
Cause companies and, therefore, have different characteristics. (IDTECK cards are made according to the MIFARE card of Philips.) 1. Depending on the card manufacturer and special manufacturing processes, the characteristics of the card may vary. Therefore, make sure that the cards are manufactured by one company. -
Page 17: Fcc Registration Information
12. FCC Registration Information FCC REQUIREMENTS PART 15 Caution: Any changes or modifications in construction of this device which are not expressly approved by the manufacturer for compliance could void the user's authority to operate the equipment. NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions;... -
Page 18: Warranty And Service
370 Amapola Ave, #106 Torrance, CA 90501 Tel: 310-782-8383 Fax: 310-782-8298 E-mail: rflogics@rflogics.com Website: www.rflogics.com Hong Kong Branch: IDTECK Hong Kong 12/F, B2B Centre, No.36 Connaught Road West, Hong Kong Tel: 852-2581-9580 Fax: 852-2234-5150 E-mail: alchu@qala.com.hk Website: www.ristarhk.com Please use the original container, or pack the unit(s) in a sturdy carton with sufficient packing to prevent damage, include the following information: 1. -
Page 19: Template
14. Template... - Page 20 The specifications contained in this manual are subject to change without notice at any time. 5F, Ace Techno Tower B/D, 684-1, Deungchon-Dong, Gangseo-Gu, Seoul, 157-030, Korea Tel : +82-(2)-2659-0055 Fax : +82-(2)-2659-0086 E-mail : webmaster@idteck.com MARSR30HK3X June 2008 Copyright ©IDTECK Co., Ltd. MARSR3UHK1X MARSR3BHK3X...