Digital Projection M-Vision 930 Series User Manual
High brightness digital video projector
Hide thumbs
Also See for M-Vision 930 Series:
- User manual (197 pages) ,
- Important information manual (30 pages) ,
- User manual (215 pages)
Related Manuals for Digital Projection M-Vision 930 Series
Summary of Contents for Digital Projection M-Vision 930 Series
-
Page 1: User Manual
USER MANUAL INSTALLATION AND QUICK-START GUIDE CONNECTION GUIDE OPERATING GUIDE M-Vision 930 Series REFERENCE GUIDE High Brightness Digital Video Projector Rev B July 2014 115-072B... - Page 2 NOTE: this symbol indicates that there is some important information that you should read. Product revision Because we at Digital Projection continually strive to improve our products, we may change specifications and designs, and add new features without prior notice.
- Page 3 NoTOC M-Vision 930 Series M-Vision 930 Series Introduction Notes Congratulations on your purchase of this Digital Projection product. Your projector has the following key features: • Support for most 3D formats. • HDBaseT® for transmission of uncompressed High Definition Video up to 100 m from the source.
-
Page 4: Table Of Contents
Digital Projection Digital Projection NoTOC M-Vision 930 Series M-Vision 930 Series CONTENTS CONNECTION GUIDE INSTALLATION AND QUICK-START GUIDE ................21 ......1 SIGNAL INPUTS ................23 WHAT’S IN THE BOX? ..............3 Digital inputs and outputs ..............23 CONNECTING THE POWER SUPPLY ..........4 Analog inputs .................. - Page 5 Digital Projection Digital Projection NoTOC M-Vision 930 Series M-Vision 930 Series CONTENTS (continued) OPERATING GUIDE Color menu..................41 ................31 ..................41 Color Space USING THE MENUS ..............33 ................42 Color Temperature Opening the OSD ................33 ....................43 Gamut Opening a menu..................
- Page 6 Digital Projection Digital Projection NoTOC M-Vision 930 Series M-Vision 930 Series CONTENTS (continued) Information menu ................66 FRAME RATES AND PULLDOWNS EXPLAINED ......91 ..................66 Interlaced and progressive scan ............91 Factory Reset Frame rates of image sources ............91 Pulldowns - conversion into destination formats .........
- Page 7 Digital Projection Digital Projection NoTOC M-Vision 930 Series M-Vision 930 Series CONTENTS (continued) APPENDIX E: WIRING DETAILS ..........109 Signal inputs and outputs ..............109 ....................109 ................... 110 HDMI 1 and 2 ....................111 ..................112 Component 2 Control connections ................113 ....................
- Page 8 Digital Projection M-Vision 930 Series This page is intentionally left blank.
-
Page 9: Installation And Quick-Start Guide
INSTALLATION AND QUICK-START GUIDE M-Vision 930 Series High Brightness Digital Video Projector Rev B July 2014... - Page 10 Digital Projection IN THIS GUIDE Installation and Quick-Start Guide M-Vision 930 Series IN THIS GUIDE What’s In The Box? ..................... 3 Connecting The Power Supply ................ 4 Projector Overview ..................... 5 Front and rear views ....................Control panel indicators .....................
-
Page 11: What's In The Box
Digital Projection WHAT’S IN THE BOX? Installation and Quick-Start Guide M-Vision 930 Series What’s In The Box? Notes Make sure your box contains everything listed. If any pieces are missing, contact your dealer. You should save the original box and packing materials, in case you ever need to ship your projector. -
Page 12: Connecting The Power Supply
Digital Projection CONNECTING THE POWER SUPPLY Installation and Quick-Start Guide M-Vision 930 Series Connecting The Power Supply Notes Make sure the voltage switch is Use only the power cable set to the correct voltage. provided. Make sure the mains power button is in the OFF position. -
Page 13: Projector Overview
Digital Projection PROJECTOR OVERVIEW Installation and Quick-Start Guide M-Vision 930 Series Projector Overview Notes Front and rear views Air inlet Lens Front infrared window Air inlet Connection panel Control panel Rear infrared window Front view Lamp enclosures with air outlets... -
Page 14: Control Panel Indicators
Digital Projection PROJECTOR OVERVIEW Installation and Quick-Start Guide M-Vision 930 Series Control panel indicators Notes During power on, all LED indicators become lit while the projector is INPUT During startup all LEDs light up running a self test. at the same time to indicate the projector is carrying out a self-test. -
Page 15: Remote Control
Digital Projection REMOTE CONTROL Installation and Quick-Start Guide M-Vision 930 Series Remote Control Notes POWER Power ON / OFF Input selection SOURCE Input selection buttons: Select input source. • - HDMI 1 • 2 - HDMI 2 Navigation MUTE •... - Page 16 Digital Projection REMOTE CONTROL Installation and Quick-Start Guide M-Vision 930 Series Remote control - continued from previous page Notes POWER BRIGHTNESS Bring up the Brightness control, then adjust the value with the LEFT RIGHT arrow buttons. SOURCE O-SCAN Switch to...
-
Page 17: Infrared Reception
Digital Projection REMOTE CONTROL Installation and Quick-Start Guide M-Vision 930 Series Infrared reception Notes The projector has infrared sensors at the front and back. 40° The angle of acceptance is 40°. Make sure that the remote control is within the angle of acceptance when trying to control the projector. -
Page 18: Positioning The Screen And Projector
Digital Projection POSITIONING THE SCREEN AND PROJECTOR Installation and Quick-Start Guide M-Vision 930 Series Positioning The Screen And Projector Notes Install the screen, ensuring that it is in the best position for viewing by your audience. Mount the projector, ensuring that it is at a suitable distance from the screen for the image to fill the screen. Set the adjustable feet so that Always allow the projector the projector is level, and perpendicular to the screen. -
Page 19: Changing The Lens
Digital Projection CHANGING THE LENS Installation and Quick-Start Guide M-Vision 930 Series Changing The Lens Notes Inserting a new lens Before changing the lens, always make sure the projector is switched off and fully disconnected from its power supply. Remove the lens cover. -
Page 20: Removing The Lens
Digital Projection CHANGING THE LENS Installation and Quick-Start Guide M-Vision 930 Series Removing the lens Notes Push the button all the way in. Before changing the lens, Rotate the lens counterclockwise until it disengages. always make sure the projector Slowly pull the lens out... -
Page 21: Changing The Filters
Digital Projection CHANGING THE FILTERS Installation and Quick-Start Guide M-Vision 930 Series Changing The Filters Notes The projector contains four identical replaceable filters accessible via the air inlets. To replace the filters on the right-hand side of the projector: Before changing the filters,... - Page 22 Digital Projection CHANGING THE FILTERS Installation and Quick-Start Guide M-Vision 930 Series To replace the filters on the left-hand side of the projector: Notes Loosen the three screws on the cover of the air inlet and remove the cover. 2.
-
Page 23: Changing The Lamps
Digital Projection CHANGING THE LAMPS Installation and Quick-Start Guide M-Vision 930 Series Changing The Lamps Notes Before removing the lamp modules for replacement, turn off the projector and unplug the power cord. Let the projector cool for approximately 60 minutes. - Page 24 Digital Projection CHANGING THE LAMPS Installation and Quick-Start Guide M-Vision 930 Series Notes Insert the new lamps (Fig 4). Fig. 4 Fig. 5 Replace the lamp covers (Fig. 5). Firmly secure the screws on the lamp covers (Fig. 6). Fig. 6...
-
Page 25: Operating The Projector
Digital Projection OPERATING THE PROJECTOR Installation and Quick-Start Guide M-Vision 930 Series Operating The Projector Notes Switching the projector on See also Connecting The Power Supply Connect the power cable between the mains supply and the projector. Switch on at the switch next to the power connector. -
Page 26: Selecting An Input Signal Or Test Pattern
Digital Projection OPERATING THE PROJECTOR Installation and Quick-Start Guide M-Vision 930 Series Selecting an input signal or test pattern Notes Input signal • Connect an image source to the projector. The signal should be automatically detected by the projector, and should be displayed within For full details of how to use the two or three seconds. -
Page 27: Adjusting The Lens
Digital Projection OPERATING THE PROJECTOR Installation and Quick-Start Guide M-Vision 930 Series Adjusting the lens Notes The lens can be adjusted using the Lens menu, or using the LENS button on the Lens Control remote control. button opens the setting, which adjusts zoom, focus... -
Page 28: Adjusting The Image
Digital Projection OPERATING THE PROJECTOR Installation and Quick-Start Guide M-Vision 930 Series Adjusting the image Notes Orientation • Setup menu This can be set from the Setup menu. Orientation Highlight Orientation and choose from Desktop Front Ceiling Front Desktop Rear... -
Page 29: Connection Guide
CONNECTION GUIDE M-Vision 930 Series High Brightness Digital Video Projector Rev B July 2014... - Page 30 Digital Projection IN THIS GUIDE Connection Guide M-Vision 930 Series IN THIS GUIDE Signal Inputs ....................... 23 Digital inputs and outputs ..................Analog inputs ......................EDID on the DVI and VGA inputs ................Using HDMI/DVI switchers with the projector ............
-
Page 31: Signal Inputs
Digital Projection SIGNAL INPUTS Connection Guide M-Vision 930 Series Signal Inputs Notes Digital inputs and outputs For a complete listing of all supported signal input modes, see Appendix C: Supported Signal HDBaseT Input Modes in the Reference Receives digital signal from HDBaseT-compliant Guide. -
Page 32: Analog Inputs
Digital Projection SIGNAL INPUTS Connection Guide M-Vision 930 Series Analog inputs Notes Component 1 Component 2 For a complete listing of all supported signal input modes, see The Component inputs use colorspaces assigned Appendix C: Supported Signal from the setting in the menu. -
Page 33: Edid On The Dvi And Vga Inputs
Digital Projection SIGNAL INPUTS Connection Guide M-Vision 930 Series EDID on the DVI and VGA inputs Notes If you are using a computer DVI card or another source that obeys the EDID protocol, the source will automatically configure itself to suit the projector. -
Page 34: 3D Connections
Digital Projection SIGNAL INPUTS Connection Guide M-Vision 930 Series 3D connections Notes 3D sources up to 60Hz requiring frame doubling and left/right interleaving Connect to either of the following inputs on the connection panel: For a complete listing of all •... -
Page 35: 3D Sync
Digital Projection SIGNAL INPUTS Connection Guide M-Vision 930 Series 3D Sync Notes 3D Sync in Sync input signal. For a complete listing of pin • configurations for all signal and Connect the 3D sync from your graphics card control connectors, see Appendix or server. -
Page 36: Control Connections
Digital Projection CONTROL CONNECTIONS Connection Guide M-Vision 930 Series Control Connections Notes • For a list of all commands used to All of the projector’s features can be controlled via a LAN control the projector via LAN, see connection, using commands described in the Protocol Guide. -
Page 37: Lan Connection Examples
Digital Projection CONTROL CONNECTIONS Connection Guide M-Vision 930 Series LAN connection examples Notes The projector’s features can be controlled via a LAN connection, using a standard internet browser or a terminal-emulation program. Crossed LAN cable Computer Projector Un-crossed LAN cables... -
Page 38: Rs232 Connection Example
Digital Projection CONTROL CONNECTIONS Connection Guide M-Vision 930 Series RS232 connection example Notes Null-modem cable Computer Projector RS232 Rev B July 2014... -
Page 39: Operating Guide
OPERATING GUIDE M-Vision 930 Series High Brightness Digital Video Projector Rev B July 2014... - Page 40 Digital Projection IN THIS GUIDE Operating Guide M-Vision 930 Series IN THIS GUIDE Using The Menus ....................33 RGB Lift and Gain ......................Opening the OSD ...................... Geometry menu ......................Opening a menu ......................Aspect Ratio ........................Exiting menus and closing the OSD ...............
-
Page 41: Using The Menus
Digital Projection USING THE MENUS Operating Guide M-Vision 930 Series POWER Using The Menus Notes INPUT Opening the OSD SOURCE Access the various menus using either the projector control panel or the remote MENU STBY control. On either device, ENTER •... -
Page 42: Inside A Menu
Digital Projection USING THE MENUS Operating Guide M-Vision 930 Series Inside a menu Notes MENU>>Sub-menu>> When you open a menu, the page consists of the following elements: • Highlighted Item Value Title bar at the top Shows which menu (and sub-menu) you have accessed. -
Page 43: Editing Projector Settings
Digital Projection USING THE MENUS Operating Guide M-Vision 930 Series Editing projector settings Notes MENU>> If the highlighted menu item is a setting with a list of values to choose from, you can change the value in two different ways. -
Page 44: Using The Projector
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Using The Projector Notes Input HDMI1 Main menu If no input is connected, the Image • Test Pattern Input Advanced Image menus will Lens Press ENTER/SELECT to open the list of available inputs. -
Page 45: Lens Menu
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Lens menu Notes Lens >> Lens Control Lens Control < Execute > Lens Control settings operate in Zoom/Focus Adjustment Shift Lens Center < Execute > mode. Adjustment When in mode: Zoom/Focus Adjustment •... -
Page 46: Image Menu
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Image menu Notes Image >> Picture Mode Bright Picture Mode Brightness Choose from Bright Presentation Video Contrast Press to open the list. ENTER/SELECT Gamma Dynamic Black Use the arrow buttons to select a picture mode from the list,... -
Page 47: Gamma
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Image menu continued from previous page Notes Image >> Gamma Picture Mode Choose a de-gamma curve from 2.35 Brightness Used correctly, the Gamma setting can improve contrast while maintaining good Contrast details for blacks and whites. -
Page 48: Position And Phase
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Image menu continued from previous page Notes Image >> Position and Phase Position and Phase V Position Press ENTER/SELECT to open the submenu. H Position • V Position H Position Phase –... -
Page 49: Color Menu
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Color menu Notes Color >> Color Space Auto Color Space Color Temperature 6500K In most cases, the Auto setting determines the correct colorspace to use. If it does Color Gamut... -
Page 50: Color Temperature
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Color menu continued from previous page Notes Color >> Color Temperature Color Space 5500K Choose a value from 5500K (warmer) to 9300K (cooler) or Native Color Temperature correction). 6500K Color Gamut... -
Page 51: Gamut
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Color menu continued from previous page Notes Color >> Gamut Color Space Auto In most cases, the Auto setting will determine the correct color gamut to use. Color Temperature If it does not, you can select the appropriate setting manually. -
Page 52: Geometry Menu
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Geometry menu Notes Geometry >> This menu allows you to compensate for image distortions caused by an unusual projection angle or irregular screen surface. Aspect Ratio 16:10 Some controls in the... -
Page 53: Overscan
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Geometry menu continued from previous page Notes Geometry >> Overscan Aspect Ratio Use this setting to compensate for noisy or badly defined image edges. Overscan Crop Crop removes unwanted artifacts from the edges of your image by cropping the Keystone edges. -
Page 54: Keystone
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Geometry menu continued from previous page Notes Geometry >> Keystone Aspect Ratio 16:10 Use this setting to compensate for any distortion caused by the projector being in corrections are Keystone Overscan a different horizontal or vertical plane to the screen. - Page 55 Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Geometry menu continued from previous page Notes Keystone settings corrections are Keystone Projector to the left unavailable when using any of the The projector is positioned following: to the left of the screen.
-
Page 56: Rotation
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Geometry menu continued from previous page Notes Geometry >> Rotation Aspect Ratio 16:10 is unavailable when using Rotation Overscan any of the following: Keystone • Keystone Rotation Rotation example •... -
Page 57: Pincushion / Barrel
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Geometry menu continued from previous page Notes Geometry >> Pincushion / Barrel Aspect Ratio 16:10 is unavailable Pincushion / Barrel Overscan when using any of the following: Keystone • Keystone Rotation •... -
Page 58: Corners
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Geometry menu continued from previous page Notes Geometry >> Corners Aspect Ratio 16:10 For each corner, apply horizontal and / or vertical correction as necessary to Corner corrections are unavailable Overscan restore the rectangular shape of the image. -
Page 59: Reset
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Geometry menu continued from previous page Notes Geometry >> Reset Aspect Ratio 16:10 This command allows you to reset all Geometry settings apart from Blanking command does not apply Reset Overscan and restore the factory default values. -
Page 60: Blanking
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Geometry menu continued from previous page Notes Geometry >> Blanking >> Blanking Select the edge you wish to blank and use the LEFT RIGHT arrow corrections are Blanking Bottom buttons to determine the amount of correction. -
Page 61: Edge Blend Menu
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Edge Blend menu Notes Edge Blend >> • Edge Blend Enable and disable Edge Blend Edge Blend When is set to Edge Blend • Align Pattern Align Pattern all other edge blend settings are... -
Page 62: Blend Width
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Edge Blend menu continued from previous page Notes Edge Blend >> Blend Width >> Blend Width Use the LEFT RIGHT arrow buttons to set the width of the blended Some controls in the... -
Page 63: Black Level Uplift
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Edge Blend menu continued from previous page Notes Edge Blend >> Black Level Uplift >> Black Level Uplift Select Area Black in the blended regions appears less dark than in the rest of the image. -
Page 64: Possible Geometry And Edge Blend Combinations
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Possible Geometry and Edge Blend combinations Notes Some Geometry Edge Blend settings cannot be used in combination with others. The table below shows the possible combinations: ... -
Page 65: 3D Menu
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series 3D menu Notes 3D >> Use this menu to enable, disable and set up 3D input, as follows: • 3D Format Auto — 3D Format Auto Side by Side (Half) -
Page 66: 3D Types
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series 3D menu continued from previous page Notes 3D types In most situations you can use the Auto setting to have the projector automatically detect the format. Otherwise, consider the notes below to help you set up the 3D input manually. -
Page 67: Some 3D Settings Explained
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series 3D menu continued from previous page Notes Some 3D settings explained Fully on Right Left In order to achieve maximum light Dark Time output and a smooth grayscale, Ghosting can be caused by the left and right images... -
Page 68: Frame Rate Multiplication In 3D Images
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series 3D menu continued from previous page Notes Frame rate multiplication in 3D images When displaying a low frame rate 3D video, the projector multiplies the frame rate to obtain a flicker-free image. For... -
Page 69: Lamps Menu
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Lamps menu Notes • Lamp Mode will automatically set the lamp power to 80%. Normal will set the power LAMPS >> to 92%.Set to if you wish to adjust the power manually, from 80% to Power 100%. -
Page 70: Setup Menu
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Setup menu Notes Setup >> • Orientation Choose from Desktop Front Ceiling Front Desktop Rear Orientation Desktop Front Ceiling Rear Auto Power Off • Auto Power Off Auto Power On... -
Page 71: Network
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Setup menu continued from previous page Notes Setup >> Network Network DHCP DHCP if the IP address is to be assigned by a DHCP server, or if it is IP Address 192. -
Page 72: On Screen Display
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Setup menu continued from previous page Notes Setup >> On Screen Display >> On Screen Display Position Center • Position Transparency Select from the list where you want the OSD to appear on the screen. -
Page 73: Presets
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Setup menu continued from previous page Notes Setup >> Presets >> Presets Recall Preset Default The current image settings can be saved as a preset, which you can recall later. -
Page 74: Information Menu
Digital Projection USING THE PROJECTOR Operating Guide M-Vision 930 Series Information menu Notes Information >> This menu gives information about software and hardware configuration, input source and lamp operating times It also allows you to restore the factory default Model Name : M-Vision WUXGA 930–3D... -
Page 75: Reference Guide
REFERENCE GUIDE M-Vision 930 Series High Brightness Digital Video Projector Rev B July 2014... - Page 76 Digital Projection IN THIS GUIDE Reference Guide M-Vision 930 Series IN THIS GUIDE The DMD™ ......................70 Appendix A: Lens Part Numbers ..............94 Choosing A Lens ....................72 Appendix B: Lens Charts ................95 Basic calculation ....................... How to use the lens charts ....................
- Page 77 Digital Projection IN THIS GUIDE Reference Guide M-Vision 930 Series IN THIS GUIDE (continued) Appendix E: Wiring Details ................109 Signal inputs and outputs ..................VGA ..........................HDMI 1 and 2 ....................... DVI ..........................Component 2 ....................... Control connections ....................
-
Page 78: The Dmd
Digital Projection THE DMD™ Reference Guide M-Vision 930 Series The DMD™ Notes A DMD™ (Digital Micromirror Device™) is a true digital light modulator which utilises an array of up to 2.3 million moving aluminium mirrors, with each one representing a pixel in the final projected image. The outermost micromirrors in the array remain inactive (pond of mirrors) and are not used in constructing the image. - Page 79 Digital Projection THE DMD™ Reference Guide M-Vision 930 Series Notes Depending on the voltage polarity applied, each mirror will either tilt to the left to produce a bright pixel or to the right for a dark pixel. When light is applied to the complete DMD™, only the light redirected from a mirror tilting to the left is projected.
-
Page 80: Choosing A Lens
Digital Projection CHOOSING A LENS Reference Guide M-Vision 930 Series Choosing A Lens Notes A number of lenses are available. Which lens you choose depends on the screen size, image aspect ratio, throw distance and light output. For information about individual lens... -
Page 81: Basic Calculation
Digital Projection CHOOSING A LENS Reference Guide M-Vision 930 Series Basic calculation Notes Identify the required lens by calculating the throw ratio. A throw ratio is the ratio of the throw distance to the screen width: The basic calculation on this page... -
Page 82: Basic Calculation Example
Digital Projection CHOOSING A LENS Reference Guide M-Vision 930 Series Basic calculation example Notes Calculate the throw ratio using the formula. The basic calculation on this page does not take into consideration Your screen is 3.5 m wide and you wish to place the projector INFORMATION YOU NEED FOR THIS CALCULATION DMD™... -
Page 83: Full Lens Calculation
Digital Projection CHOOSING A LENS Reference Guide M-Vision 930 Series Full lens calculation Notes Introducing TRC The choice of lens will affect the image size and will address discrepancies between the DMD™ resolution and the source. TRC can only be applied if greater When an image fills the height of the DMD™... -
Page 84: Calculating Trc
Digital Projection CHOOSING A LENS Reference Guide M-Vision 930 Series Calculating TRC Notes To calculate TRC, use the following formula: 1.6 (DMD™ aspect ratio) TRC can only be applied if greater TRC = than 1. If TRC is 1 or less, disregard... -
Page 85: Calculating The Throw Ratio With Trc
Digital Projection CHOOSING A LENS Reference Guide M-Vision 930 Series Calculating the throw ratio with TRC Notes For TRC > 1, amend the basic throw ratio formula as follows: Throw distance TRC can only be applied if greater Throw ratio = than 1. -
Page 86: Full Lens Calculation Example
Digital Projection CHOOSING A LENS Reference Guide M-Vision 930 Series Full lens calculation example Notes Your screen is 3.5 m wide; you wish to place the projector INFORMATION YOU NEED FOR THESE CALCULATIONS approximately 6.8 m from the screen. The source is 4:3. -
Page 87: Screen Requirements
Digital Projection SCREEN REQUIREMENTS Reference Guide M-Vision 930 Series Screen Requirements Notes Fitting the image to the DMD™ If the source image supplied to the projector is smaller than the DMD™ resolution, the image will not fill the DMD™. The following examples show how a number of common formats may be displayed. -
Page 88: Wuxga Images Displayed With A Height Of 1080 Pixels
Digital Projection SCREEN REQUIREMENTS Reference Guide M-Vision 930 Series WUXGA images displayed with a height of 1080 pixels Notes 4:3 = 1.33:1 = 1440 pixels 16:10 = 1.6:1 = 1728 pixels 1.66:1 (Vista) = 1792 pixels full width = 1920 pixels... -
Page 89: Wuxga Images Displayed Full Height
Digital Projection SCREEN REQUIREMENTS Reference Guide M-Vision 930 Series WUXGA images displayed full height Notes Only WUXGA or UXGA images can fill the full height of the DMD™, using all 1200 pixels without scaling. UXGA = 4:3 = 1.33:1 = 1600 pixels WUXGA = 16:10 = 1.6:1 = 1920 pixels... -
Page 90: Diagonal Screen Sizes
Digital Projection SCREEN REQUIREMENTS Reference Guide M-Vision 930 Series Diagonal screen sizes Notes Screen sizes are sometimes specified by their diagonal size (D). When dealing W = width with large screens and projection distances at different aspect ratios, it is more convenient to measure screen width (W) and height (H). -
Page 91: Fitting The Image To The Screen
Digital Projection SCREEN REQUIREMENTS Reference Guide M-Vision 930 Series Fitting the image to the screen Notes It is important that your screen is of sufficient height and width to display images at all the aspect ratios you are planning to use. -
Page 92: Positioning The Screen And Projector
Digital Projection SCREEN REQUIREMENTS Reference Guide M-Vision 930 Series Positioning the screen and projector Notes For optimum viewing, the screen should be a flat surface perpendicular to the floor. The bottom of the screen should The projector should be installed be 1.2 m (4 feet) above the floor and the front row of the... -
Page 93: Positioning The Image
Digital Projection POSITIONING THE IMAGE Reference Guide M-Vision 930 Series Positioning The Image Notes The normal position for the projector is at the centre of the screen. However, you can set the projector above or below the centre, or to one side, and adjust the image using the Lens shift feature (known as rising and falling front) to maintain a geometrically correct image. - Page 94 Digital Projection POSITIONING THE IMAGE Reference Guide M-Vision 930 Series Notes Any single adjustment outside the ranges specified on the following page may result in an unacceptable level of distortion, particularly at the corners of the image, due to the image passing through the periphery of the lens optics.
-
Page 95: Maximum Offset Range
Digital Projection POSITIONING THE IMAGE Reference Guide M-Vision 930 Series Maximum offset range Notes The maximum offset range available with no distortion or vignetting is dependent on which lens is used. Shifting the lens beyond its undistorted limits may be physically possible, however you may experience some vignetting or distortion. -
Page 96: Aspect Ratios Explained
Digital Projection ASPECT RATIOS EXPLAINED Reference Guide M-Vision 930 Series Aspect Ratios Explained Notes The appearance of a projected image on the screen depends on a combination of the following: • The DMD™ resolution is WUXGA with a 1920 x 1200 resolution, corresponding to an aspect ratio of 16:10 •... -
Page 97: Aspect Ratio Examples
Digital Projection ASPECT RATIOS EXPLAINED Reference Guide M-Vision 930 Series Aspect ratio examples Notes Source: 4:3 Aspect Ratio: Source / 4:3 Aspect Ratio: 16:10 Source: 16:9 Aspect Ratio: Source / 16:9 Aspect Ratio: 16:10 Source: 16:10 (native) Unused screen areas... - Page 98 Digital Projection ASPECT RATIOS EXPLAINED Reference Guide M-Vision 930 Series Aspect ratio example: TheaterScope Notes Notes TheaterScope setting is used in combination with an anamorphic lens to restore 2.35:1 images packed into a 16:9 frame. Such images are projected with black lines at the top and bottom of the 16:9 screen to make up for the difference in aspect ratios.
-
Page 99: Frame Rates And Pulldowns Explained
Digital Projection FRAME RATES AND PULLDOWNS EXPLAINED Reference Guide M-Vision 930 Series Frame Rates And Pulldowns Explained Notes Interlaced and progressive scan A progressive scan is a method of updating the image by drawing all the lines of each frame in a sequence. In contrast, interlaced video alternately scans odd and even lines. -
Page 100: Pulldowns - Conversion Into Destination Formats
Digital Projection FRAME RATES AND PULLDOWNS EXPLAINED Reference Guide M-Vision 930 Series Pulldowns - conversion into destination formats Notes Pulldowns are a method of converting a 24p source into a different destination format by adding extra frames to the source. -
Page 101: 2:3:3:2 (Advanced) Pulldown
Digital Projection FRAME RATES AND PULLDOWNS EXPLAINED Reference Guide M-Vision 930 Series 2:3:3:2 (advanced) pulldown Notes This method is very similar to the normal pulldown. Unlike the normal pulldown method, the resulting 30 fps video sequence contains only one frame containing fields from two different source frames. -
Page 102: Appendix A: Lens Part Numbers
Digital Projection APPENDIX A: LENS PART NUMBERS Reference Guide M-Vision 930 Series Appendix A: Lens Part Numbers Notes The throw ratios given here apply only when the image fills the width of the DMD. Throw ratios Part number Throw distance range... -
Page 103: Appendix B: Lens Charts
Digital Projection APPENDIX B: LENS CHARTS Reference Guide M-Vision 930 Series Appendix B: Lens Charts Notes How to use the lens charts For information about individual lens The lens charts on the following pages provide a quick guide to the part numbers and lens extension type of lens needed for a particular projector. -
Page 104: Trc Values Applied In The Charts
Digital Projection APPENDIX B: LENS CHARTS Reference Guide M-Vision 930 Series TRC values applied in the charts Notes Full width images For information about individual lens Formats that fit the width of the DMD™ without applying a throw ratio correction (TRC) include:... -
Page 105: Full Dmd™ Width Images
Digital Projection APPENDIX B: LENS CHARTS Reference Guide M-Vision 930 Series Full DMD™ width images Notes Full width images are 2.35:1 (Scope), 1.85:1 (Flat) 1.78:1 (16:9), 1.66:1 (Vista) and 1.6:1 (native). This chart has a TRC of 1.0, for use 0.84 - 1.03 : 1 zoom lens... -
Page 106: 1.25:1 Images
Digital Projection APPENDIX B: LENS CHARTS Reference Guide M-Vision 930 Series 1.25:1 images Notes This chart has a TRC of 1.28, for 12 m (39.4 ft) 0.84 - 1.03 : 1 zoom lens use with the following images: 1.56 - 1.86 : 1 zoom lens 1.85 - 2.40 : 1 zoom lens... -
Page 107: Images
Digital Projection APPENDIX B: LENS CHARTS Reference Guide M-Vision 930 Series 1.33:1 images Notes This chart has a TRC of 1.2, for use 0.84 - 1.03 : 1 zoom lens 12 m (39.4 ft) with the following images: 1.56 - 1.86 : 1 zoom lens 1.85 - 2.40 : 1 zoom lens... -
Page 108: Appendix C: Supported Signal Input Modes
Digital Projection APPENDIX C: SUPPORTED SIGNAL INPUT MODES Reference Guide M-Vision 930 Series Appendix C: Supported Signal Input Modes Notes 2D input modes SDTV 480i 720 x 480 59.94 15.73 ü 576i 720 x 576 50.00 15.63 ü EDTV 480p59 720 x 480 59.94... - Page 109 Digital Projection APPENDIX C: SUPPORTED SIGNAL INPUT MODES Reference Guide M-Vision 930 Series Notes COMPUTER SVGA60 800 x 600 60.32 37.88 ü ü ü (continued) SVGA75 800 x 600 75.00 46.88 ü ü ü SVGA85 800 x 600 85.06 53.67 ü...
-
Page 110: 3D Input Modes
Digital Projection APPENDIX C: SUPPORTED SIGNAL INPUT MODES Reference Guide M-Vision 930 Series 3D input modes Notes Only the HDMI 1 & 2 and HDBaseT inputs support HDMI 1.4 3D formats. SXGA60 Dual Pipe 1280 x 1024 60.02 1066 63.98 ü... -
Page 111: Appendix D: Menu Map
Digital Projection APPENDIX D: MENU MAP Reference Guide M-Vision 930 Series Appendix D: Menu Map Notes Menu Sub Menus Some of the information in this menu MAIN map is summarised. See the actual menu on the projector for full details. -
Page 112: Color
Digital Projection APPENDIX D: MENU MAP Reference Guide M-Vision 930 Series Notes Menu Sub Menus Some of the information in this menu COLOR map is summarised. See the actual Color Space Auto, YPbPr, YCbCr, RGB PC, RGB Video menu on the projector for full details. -
Page 113: Geometry
Digital Projection APPENDIX D: MENU MAP Reference Guide M-Vision 930 Series Notes Menu Sub Menus Some of the information in this menu GEOMETRY map is summarised. See the actual Aspect Ratio 16:9, TheaterScope, 4:3, 4:3 Narrow, 16:10, 5:4, Source menu on the projector for full details. -
Page 114: Edge Blend
Digital Projection APPENDIX D: MENU MAP Reference Guide M-Vision 930 Series Notes Menu Sub Menus Some of the information in this menu EDGE BLEND map is summarised. See the actual Edge Blend Off, On menu on the projector for full details. -
Page 115: Setup
Digital Projection APPENDIX D: MENU MAP Reference Guide M-Vision 930 Series Notes Menu Sub Menus Some of the information in this menu SETUP map is summarised. See the actual Orientation Desktop Front, Ceiling Front, Desktop Rear, Ceiling Rear menu on the projector for full details. -
Page 116: Information
Digital Projection APPENDIX D: MENU MAP Reference Guide M-Vision 930 Series Notes Menu Sub Menus Some of the information in this menu INFORMATION map is summarised. See the actual Model Name (information only) menu on the projector for full details. -
Page 117: Appendix E: Wiring Details
Digital Projection APPENDIX E: WIRING DETAILS Reference Guide M-Vision 930 Series Appendix E: Wiring Details Notes Signal inputs and outputs 15 way D-type connector VGA: pin view of female connector unused Digital Ground (H Sync) R Ground B Ground G Ground... -
Page 118: Hdmi 1 And 2
Digital Projection APPENDIX E: WIRING DETAILS Reference Guide M-Vision 930 Series HDMI 1 and 2 Notes 19 way type A connector TMDS Data 2+ TMDS Data 2 Shield HDMI: pin view of panel connector TMDS Data 2- TMDS Data 1+... -
Page 119: Dvi
Digital Projection APPENDIX E: WIRING DETAILS Reference Guide M-Vision 930 Series Notes 24 way D-type connector Pin 1 TMDS data 2− Digital red− (link 1) High-bandwidth Digital Content Pin 2 TMDS data 2+ Digital red+ (link 1) Protection (HDCP) is supported on... -
Page 120: Component 2
Digital Projection APPENDIX E: WIRING DETAILS Reference Guide M-Vision 930 Series Component 1 Notes 3 x RCA Phono connector Component 1: 3 x RCA Phono connector High-bandwidth Digital Content Component 2 Protection (HDCP) is supported on 3 x 75 ohm BNC connector this input. -
Page 121: Control Connections
Digital Projection APPENDIX E: WIRING DETAILS Reference Guide M-Vision 930 Series Control connections Notes Only one remote connection (RS232 or LAN) should be used at any one RJ45 socket time. Update port RS232 9 way D-type connector 1 unused 2 Received Data (RX) -
Page 122: Trigger 1 & Trigger 2
Digital Projection APPENDIX E: WIRING DETAILS Reference Guide M-Vision 930 Series Trigger 1 & Trigger 2 Notes Sleeve 3.5 mm mini jack Signal Sleeve Ground IR input Sleeve 3.5 mm mini jack Signal Ring Not connected Ring Sleeve Ground USB type A socket... -
Page 123: Appendix F: Glossary Of Terms
Digital Projection APPENDIX F: GLOSSARY OF TERMS Reference Guide M-Vision 930 Series Appendix F: Glossary Of Terms Notes 1080p HDTV resolution which corresponds to 1920 x 1080 pixels (a widescreen aspect ratio of 16:9). 3D active glasses Wireless battery-powered glasses with LCD shutters. Synchronization information is communicated to the glasses by means of an infrared (IR) or radio frequency (RF) emitter which is connected to the Sync Out terminal on the projector. - Page 124 Digital Projection APPENDIX F: GLOSSARY OF TERMS Reference Guide M-Vision 930 Series Aspect ratio Notes The proportional relationship between the width and the height of the projected image. It is represented by two numbers separated by a colon, indicating the ratio of image width and height respectively: for example, 16:9 or 2.35:1.
- Page 125 Digital Projection APPENDIX F: GLOSSARY OF TERMS Reference Guide M-Vision 930 Series Chrominance Notes Component Video color difference Also known as ‘C’, this is the component, or pair of components, of a signal which describes information. Color difference Component Video...
- Page 126 Digital Projection APPENDIX F: GLOSSARY OF TERMS Reference Guide M-Vision 930 Series Crop Notes Remove part of the projected image. Alternatively, fit an image into a frame with a different aspect ratio by removing part of the image. The image is resized so that either its length or its width equals the length or width of the frame, while the other dimension has moved outside the frame;...
- Page 127 Digital Projection APPENDIX F: GLOSSARY OF TERMS Reference Guide M-Vision 930 Series Edge tear Notes interlaced video An artifact observed in where the screen appears to be split horizontally. Edge tears appear when the video feed is out of sync with the refresh rate of the display device.
- Page 128 Digital Projection APPENDIX F: GLOSSARY OF TERMS Reference Guide M-Vision 930 Series Gamma Notes A nonlinear operation used to code and decode luminance. It originates from the Cathode Ray Tube technology used in legacy television sets. Ghosting An artifact in 3D image viewing. Ghosting occurs when an image intended for one eye is partially seen by the other eye.
- Page 129 Digital Projection APPENDIX F: GLOSSARY OF TERMS Reference Guide M-Vision 930 Series Interlacing Notes A method of updating the image. The screen is divided in two fields, one containing every odd horizontal line, the other one containing the even lines. The fields are then alternately updated. In analog TV interlacing was commonly used as a way of doubling the refresh rate without consuming extra bandwidth.
- Page 130 Digital Projection APPENDIX F: GLOSSARY OF TERMS Reference Guide M-Vision 930 Series NTSC (National Television Standards Committee) Notes interlaced fields The United States standard for television - 525 lines transmitted at 60 per second. OSD (on-screen display) The projector menus allowing you to adjust various settings.
- Page 131 Digital Projection APPENDIX F: GLOSSARY OF TERMS Reference Guide M-Vision 930 Series Primary colors Notes Three colors any two of which cannot be mixed to produce the third. In additive color television systems the primary colors are red, green and blue.
- Page 132 Digital Projection APPENDIX F: GLOSSARY OF TERMS Reference Guide M-Vision 930 Series Notes resolution aspect ratio. (Shortened from SXGA+, stands for Super Extended Graphics A display of 1400 x 1050 pixels with a 4:3 screen Array Plus.) Synchronization A timing signal used to coordinate an action.
- Page 133 Digital Projection APPENDIX F: GLOSSARY OF TERMS Reference Guide M-Vision 930 Series TRC (Throw ratio correction) Notes throw distances throw ratios when the image does not fill the width of the DMD™. A special number used in calculating TRC is the ratio of the DMD™...
- Page 134 Digital Projection APPENDIX F: GLOSSARY OF TERMS Reference Guide M-Vision 930 Series Notes ZScreen A special kind of light modulator which polarizes the projected image for 3D viewing. It normally requires that images are projected onto a silver screen. The ZScreen is placed between the projector lens and screen. It changes the polarization of the projected light and switches between left- and right-handed circularly polarized light at the field rate.
-
Page 135: Technical Specifications
Digital Projection TECHNICAL SPECIFICATIONS Reference Guide M-Vision 930 Series Technical Specifications Notes Digital Projection reserves the right to change product specifications without prior notice. Models The specifications on these pages refer to the following projector: Series name Resolution Part number... -
Page 136: Inputs And Outputs
Digital Projection TECHNICAL SPECIFICATIONS Reference Guide M-Vision 930 Series Inputs and outputs Notes Type Connector Type Connector Video & Computer (all models) Communication & Control HDMI 1.4 HDMI 3D Sync Out DVI-D 3D Sync In HDBaseT RJ45 RJ45 15-pin D-Sub... -
Page 137: Lenses
Digital Projection TECHNICAL SPECIFICATIONS Reference Guide M-Vision 930 Series Lenses Notes Detailed information about available lenses can be found in Appendix A: Lens Part Numbers. Further information about lens offsets can be found in Positioning The Image > Maximum offset range. -
Page 138: Electrical And Physical Specifications
Digital Projection TECHNICAL SPECIFICATIONS Reference Guide M-Vision 930 Series Electrical and physical specifications Notes • Power requirements 100-240 VAC, 50-60 Hz (single phase) • Power Consumption 1200 W • Thermal Dissipation 3771 BTU/hr • Fan Noise 48 dBA • Operating Temperature 0°C to 35°C (32 to 95F)
Need help?
Do you have a question about the M-Vision 930 Series and is the answer not in the manual?
Questions and answers