Table of Contents
Advertisement
L.P. GAS REQUIREMENTS
Connection: 1/2" N.P.T. Minimum 5/8" dia.
flex line. Pressure: 11" to 14"WC.
A regulator
is required at the L.P. source to provide a maxi-
mum of 14" WC. to the range regulator.
CONVERTING
TO L.P. GAS
ile. If the Back Guard is in place, protect the
Back Guard during removal and installation of
the griddle to prevent scratching.
4.
FOR
GRILL
UNIT
(MODEL
RG484(:;L, GG, RG364GL)
To remove the grill assembly, begin by lifting off
the front trim adjacent to the grease gutter.
Beneath the trim, you'll find tWo screws, remove
them. Remove the Briquette Rack with briquettes
(if in place). Remove the (2) screws holding the
grill igniter in place, then without removing the
wires, gently lay the igniter on the side. Use care
around the grill igniter, it is fragile. Remove the
tie wire securing thl~ grill burner then remove the
grill burner. If the Back Guard is in place, pro-
tect the Back Guard during removal and installa-
tion of the grillpar'ts to prevent scratching.
GENERAL
5. OVEN
Empty the oven, remove the tWo oven rack side
supports, the four \:;,rackets and screws holding the
oven bottom down" and then the oven bottom.
Remove the screw securing the oven burner, than
remove the burner. Replace the oven burner ori-
fice with the red color coded orifice supplied
(wired to the tubin!~). Tighten until snug.
5A
SMALL
OVEN
(48" MODELS ONLY)
Converting a range from factory set natural gas to
L.P. is best done prior to pushing the range in
place while the back of the range is accessible,
prior to installing the back guard. Begin by mak-
ing sure that the range is unplugged. Next
remove the open top burner grates and the enam-
eled pans beneath the grates. Treat all parts with
care to avoid chipping the porcelain enamel. Lift
and remove all open top burners.
2.
REGULATOR
-See Fig. 16
The convertible regulator on this unit has a nat-
ural gas setting of5.0" WC. for natural gas and
10" WC. for L.P., and can be found in the left
rear corner of the burner box. Remove the slot-
ted plug in the regulator and turn it over so that
the side stamped "L.P." faces outward, then rein-
sert ensuring it is properly locked in place.
3.
FOR
GRIDDLE
UNIT
(MODEL
RG484GD,GG,
RG364GD)
Empty the oven, remove the two side supports,
the four brackets, and screws holding the oven
bottom down, and then the oyen bottom.
Remove the screw ~;ecuring the oven burner, then
the burner. Tighten the oven orifice hood down
until seated against the integral predrilled L.P.
pin. A 1/2" deep well socket is ideal for this pur-
pose. Do not over 1:ighten.
To remove the griddle assembly, first lift off the
front trim adjacent to the grease gutter. Beneath
the trim, you'll find tWo screws,- remove them.
Also remove the rear flue cover and remove the
center shipping screw. With these screws
removed, you can now lift off the griddle plate
assembly. Lift vertically and to the rear and
remove the griddle thermostat bulb from beneath
the plate by sliding it out (Do Not Tug Hard at
the Bulb or Capillary). Then remove the screw
securing the griddle burner and remove the burn-
er. Use care around the griddle igniter, it is frag-
OVEN
BROILER
6
Remove the servicl~ panel in the rear of the
Advertisement
Table of Contents
