Connecting A Rgb Analog Source To Port 3 - Barco R9002400 Installation Manual

Source Connections

Connecting a RGB Analog source to Port 3

Connect a RGB Analog signal via an interface (e.g. RGB 120MHz interface, part number 98 26570) to Port 3: RGB analog input
with automatic sync detection (Separate H and V sync inputs, with composite sync input or with sync signals on green).
Tr rà v † ‡h y y h ‡v ‚Ã v † ‡…ˆp‡ v ‚ † à irs ‚ … rà p ‚ rp ‡v tà ‡ ‚ à ‡ u r à † ˆ ƒƒy ’ 
W‚v …Ãy h à ‚ ‡vpr à qv †‡ hyy h‡ v ‚ Ãh‰ h‡Ãq r à … hp p‚…qr… à hˆÃ … p† rh ˆ 
!  !"  ÃW
W ‚€Ã '  à r… v ƒu r… h y†
D   ‚€ & $ Ã6 € ƒ
$  % Ã C“
P A A P I
A… r „
POWER / MAINS COMM. POR T PORT 3
Pin assignment for the D9 (male) connector:
1
2
3
4
5
6
7
8
9
Settings on module level
In the case of this second RGB input there are three different settings:
1. 75 W Termination resistor
2. Blue in Green switch
3. Force Negative Sync switch
R101
Vsync R81
Hsync R41
(Blue)
When changing a switch position or removing a resistor, turn off the projector and unplug the power cord from the wall outlet.
6-4
S B 7 t… r r Ã)ƒr … h ‡ v ‚
8‚€ ƒ  C T ’ p W T’ p T  W D 9 @ P P AAÃà ÃÃà ÃP I W D9@ P P AAÃà ÃÃà ÃP I
&$ ÃPu€ &$ ÃPu€ … r qÃ)Æ ‡h qi’
P O RT 4/ 5 PORT 2
POR T 1 PROJ ECTOR MOD E
RGB 120MHz interface
&$Âu€ Ç r… €  L Q Y H U
not connected
ground RGBS
RED
GREEN
BLUE
ground RGBS
ground RGBS
Horizontal /composite sync
Vertical sync
S2 Blue in Green (ON=yes)
R1
R21
(red)
(Green)
U uv †Ã qr‰vprà p‚ €ƒ yvr†Ã v‡u à h… ‡Ã $ s
‡u rÃA 88à … ˆ yr†  ÃÃP ƒ r… h‡v‚  Ãv†Ã†ˆ iwr p‡Ã ‡‚
s‚y y‚v tÇ ‚Ãp‚qv ‡ v‚†Ã   à ÃUuv†
q r ‰v prÀh’à ‚ ‡Ã phˆ † rÃu h… €sˆ yà v ‡r… 
sr…r  pr Ãhq Ã!à ‡u v†Ãq r ‰v prÀˆ † ‡ Ã
hpprƒ‡ Ãh’ Ãv ‡r…sr… rprÃ…r pr v ‰ rq Ã
v pyˆ qv t Ãv ‡ r …sr… r p rÇ uh‡Ã €h’ Ãph ˆ †r
ˆ q r†v … rq ƒ r… h‡v ‚ Å
S1 Force negative Sync
(ON=yes)
5976195 BARCOCINE 9 31012002