Connecting A S-Video (Or Composite Video) Source To Port 2; Connecting A Rgb Analog Source To Port 4/5 - Barco GRAPHICS 808S Isntallation Manual
Hide thumbs
Also See for GRAPHICS 808S:
- Owner's manual (53 pages) ,
- Brochure & specs (2 pages) ,
- Owner's manual (55 pages)
Table of Contents
Advertisement
Source connections
Connecting a S-Video (or Composite Video)
source to Port 2
Separate Y-luma/C-chroma signals for higher quality playback of
Super VHS signals can be connected to Port 2 . The composite video
can also be connected to this port.
Press the numeric button 2 on the RCU or the local keypad.
In case of using Port 2 for connecting the Composite Video, the
selection of this source have to be done inside the "Picture Tuning"
menu. Please refer to the Owner's Manual of this projector.
75 W Termination Switch for S-video
Terminate the S-video input of the projector using the 75 W switch
next to the S-video input when the projector operates alone or when
the projector is the last unit in a loop-through configuration.
The switch is set to "ON" : signal terminated.
The switch is set to "OFF" : signal not terminated.
Connecting a RGB Analog source to Port 3
Connect a RGB Analog signal via an interface (e.g. RGB 120MHz
interface, part number 98 26570) to Port 3: RGB analog input with
automatic sync detection (Separate H and V sync inputs, with
composite sync input or with sync signals on green).
Pin configuration of the D9 (male) connector of the Analog input :
1
not connected
2
ground RGBS
3
RED
4
GREEN
5
BLUE
6
ground RGBS
7
ground RGBS
8
Horizontal /composite sync
9
Vertical sync
Press the numeric button 3 on the RCU or the local keypad.
Locations of the Termination Resistors and Switches
on the RGB Input Auto Sync Tracking Module
When changing a switch position or removing a resistor, turn off the
projector and unplug the power cord from the wall outlet.
In case of chaining (loop-through) the projectors, the 75W line
termination resistors must be removed from the RGB Input Auto Sync
Tracking Module when the projector is NOT the last unit in the chain.
In case of a stand-alone projector, do not remove the resistors.
75 W resistors on the module :
75 W resistors removed
:
7-2
All manuals and user guides at all-guides.com
line terminated.
line not terminated.
4 pin connector configurations:
For S-video:
Pin 1: earth(ground) luminance
Pin 2: earth(ground) chrominance
3
Pin 3: luminance signal(Y)
1Vpp ±3dB
4
Pin 4: chrominance signal(C)
300mVpp ±3dB
Tr rà v † ‡h y y h ‡v ‚à v † ‡…ˆp‡ v ‚ † à irs ‚ … rà p ‚ rp ‡v tà ‡ ‚ à ‡ u r à † ˆ ƒƒy ’
W‚v …Ãy h à ‚ ‡vpr à qv †‡ hyy h‡ v ‚ Ãh‰ h‡Ãq r à … hp p‚…qr… à hˆÃ … p† rh ˆ
W ‚€Ã
! !" Ã W
' Ã r… v ƒu r… h y†
S
B
7
8‚€ ƒ C T ’ p W T’ p
2))
21
D ‚€
& $ Ã 6 € ƒ
$ % Ã C“
A… r „
P O RT 4/ 5
POWER / MAINS
COMM. POR T
PORT 3
&$Âu€ Çr …€
R101
Vsync
R81
Hsync
R41
R21
(Blue)
(Green)
R1
(Red)
Line termination 75 Ω resistors
5975996 BARCOGRAPHICS 808s 241197
For video:
Pin 1: earth(ground) video
Pin 2: not connected
1
Pin 3: video signal
Pin 4: not connected
2
75 Ω Termination Switch
U uv †Ã qr‰vprà p‚ €ƒ yvr†Ã v‡u à h… ‡Ã $ s
‡u rÃA 88à … ˆ yr† ÃÃP ƒ r… h‡v‚ Ãv†Ã†ˆ iwrp‡Ã ‡‚
s‚y y‚v tÇ ‚Ãp‚qv ‡ v‚†Ã à ÃUuv†
q
v p Ã
’à ‚ ‡Ã p
† Ãu
s yà v ‡
s
p à q Ã!à ‡u v†Ãq
v p Ã
†‡ Ã
pp
‡ Ã ’ Ãv ‡ s
p Ã
p v
q Ã
v py qv t Ãv ‡ s
p Ç u ‡Ã
’ Ãp
†
q †v q Â
‡v ‚ Å
t … r r à )à ‚ ƒ r … h ‡v ‚
T
W
9 @ P
P
à à Ã
à à à P I
W
9@ P
P
à à Ã
à à à P I
&$ ÃPu€
&$ ÃPu€
… r q à )à † ‡ h q i ’
PORT 2
POR T 1
PROJ ECTOR MOD E
RGB 120MHz interface
L Q Y H U
S2 Blue in Green (ON=yes)
S1 Force Negative Sync
(ON=yes)
Advertisement
Table of Contents
