Connecting A Rgb Analog Source To Port 3; Connecting A Rgb Analog Source To Port 4/5; Connecting A Component Video Source To Port 4/5 - Barco Data 1209s Installation Manual

Procedure to remove the line termination resistors :
1 Turn off the projector and unplug the projector power cord.
2 Remove the top cover from the projector.
3 Remove the RGB Input Auto Sync Tracking Module from the main
frame.
4 Unsolder and remove the resistors.
To remove the RGB Input Auto Sync Tracking Module, press the
module locks and lift up the module handles
Blue in Green Switch on the RGB Input Auto Sync Tracking
Module
Blue characters are difficult to read, therefore the blue text will be
displayed as cyan so that the readability becomes better.
Switch in the ON position : Blue in Green active.
Switch in the OFF position : Blue in Green disabled.
WARNING : Leaving the switch in the ON position will result in
abnormal color balance of the projected image.
Force Negative Sync on the RGB Input Auto Sync
Tracking Module
Switch in the ON position : the sync pulses must be negative.
Switch in the OFF position : the sync polarity will be automatically
detected.

Connecting a RGB Analog source to Port 4/5

RGB analog input terminals with separate H and V sync inputs,
composite sync input or sync signals on green can be connected to
the projector via Port 4/5. The projector automatically detects where
the sync signal is located.
An interface is recommended when connecting a computer and local
monitor to the projector. BARCO provides the following interfaces:
Universal Analog Interface - Order no. : R9826100.
*
RGB 120 MHz Analog Interface - Order no. : R9826570.
*
VGA interface - Order no. : R9828070 (230V), R9828079 (120V)
*
MAC interface - Order no. : R9828050 (230V), R9828059 (120V)
*
MAGIK interface - Order no. : R9828129 & R9828128 (120V)
*
R9828120 & R9828121 (230V)
To select the RGB input :
Press the digit button 4 or 5 on the RCU or the local keypad.
Connecting a Component Video source to
Port 4/5
A component video (R-Y, Y, B-Y)
connected to the projector via Port 4/5. The projector automatically
detects where the sync signal is located.
An HDTV interface is recommended when connecting a computer
and local monitor to the projector. The HDTV Kit Order number :
R9828040.
To select the component video input :
Press the digit button 6 on the RCU or the local keypad.
5975718 BARCODATA 1209s 050698
All manuals and user guides at all-guides.com
with sync signals can be
RGB Input Auto Sync Tracking Module
QPSUÃ#$
SB7ÃÃCW
8‚€ƒCÆ’p WÆ’p
QPSUÃ%ÃS@HPU@
QPSUÃ"
8PHHVID86UDPI
S B 7
6I6GPBÃDIU@SAÃ !HC“
21
,1387
%
2))
5 *
QPSUÃ#$
SB7ÃÃCW
8‚ € ƒ C Æ’ p WÆ ’ p
QP SU Ã%Ã S@HPU@
Q PS UÃ"
8PHHVID86UDPI
S 7
B
W8S ÃC9 UWÃyh’r…
Source connections
QPSUÃ QPX@SH6DIT
QSPE@8UPSÃHP9@
WD9@P
BS@@IÃ)ƒr…h‡v‚hy
S@9Ã)Ƈhqi’
QPSUÃ!
TWD9@P
PAA PI PAA PI
&$Âu€
&$Âu€
+
9
, QWHUIDFH
DIQ ,13
LQY H U 
&$ u€Ã ‡r…€
363
QPSUÃ QPX@SH6DIT
QSP E@ 8UP SÃH P9 @
WD9@P
BS @@I Ã)ƒr …h‡v ‚h y
S@ 9Ã)Ƈh qi ’
QP SU Ã!
T WD9 @P 
P AA PI
PA A PI
& $Â u€ &$Âu€
6 ˆqv‚Ãh€ ƒyvsvr…

7-3