Related Manuals for Barco R9002250
Summary of Contents for Barco R9002250
- Page 8 • • • • • •...
- Page 11 11.5 cm green phospho...
- Page 12 Lock screws...
- Page 13 Í...
-
Page 14: Adjustment Mode
)URQWFHLOLQJ 5HDUFHLOLQJ SUHVVHG SUHVVHG SUHVVHG SUHVVHG 5HDUWDEOH SUHVVHG SUHVVHG SUHVVHG SUHVVHG ADJUSTMENT MODE Select a path from below: GUIDED RANDOM ACCESS INSTALLATION SERVICE IRIS source 1 Select with then <ENTER> <EXIT> to return... - Page 15 Select with then <ENTER> <EXIT> to return...
-
Page 16: Password Mode
PASSWORD MODE POWER UP MODE PASSWORD REQUIRED OPERATING MODE WHEN FOR ADJUSTMENT POWER IS SWITCHED ON PLAYING StdBY BAUD RATE TABLE TO COMPUTER P ROJE CTOR ADDRESS StdBY (sum) CODE SPEED MAIN P OWER P ROCE SSOR CYC I 2 C SHORTED BLOCK MATCH RESERVED E RROR... - Page 17 Addressable with RCU Addressable with PC, MAC or workstation PROJECTOR ADDRESS...
- Page 18 Source 2 Fh= 15.6 kHz Fv= 50 Hz OFF ON...
- Page 19 OFF ON...
- Page 20 V NOM 120/230 Volt I MAX 7/5Amp FREQ 50/60Hz...
- Page 21 230V operation 120V operation 230V 2xT5A/250V 120V 2xT10A/250V...
- Page 24 &$Âu€ Composite video ‡‚Ãr‘‡Ãƒ…‚wrp‡‚…Â… ‡‚ÃhÀ‚v‡‚… TV tuner, e.g. TVDM40 stereo Audio amplifier...
- Page 25 QPSUÃ%à /XPD&KURPD QPSUÃ" &$Âu€Ã‡r …€...
- Page 26 QPSUÃ" , QWHUIDFH &$ u€Ã ‡r…€...
- Page 27 QPSUÃ%Ã VCR HDTV player Audio amplifier...
- Page 28 RISK OF ELECTRICAL SHOCK NO USER ADJUSTABLE PARTS INSIDE THE FOLLOWING INSTALLATION MENUS ARE RESERVED TO, AND TO BE PERFORMED ONLY BY BARCO PERSONNEL, OR BARCO AUTHORIZED DEALERS IF QUALIFIED, PRESS <ENTER> TO CONTINUE, OR IF NOT, <EXIT> TO RETURN. enter password...
-
Page 29: Optical Lens Focusing
FHLOLQJ SURMHFWRU VFUHHQ OPTICAL LENS FOCUSING 1. LOOSEN THE NUT ON THE REAR OF THE XXXX LENS, ROTATE THE LENS BARREL TO FOCUS THE CENTER OF THE IMAGE, THEN TIGHTEN THE NUT 2. LOOSEN THE NUT ON THE FRONT OF THE XXXX LENS AND ROTATE THE FRONT SECTION OF THE LENS TO FOCUS THE CORNERS OF THE... -
Page 30: Raster Centering
RASTER CENTERING CONTRAST LEVEL IS REDUCED AND BRIGHTNESS INCREASED TO MAKE THE RASTER VISIBLE ON THE FACE PLATE OF EACH CRT. USE THE ARROW KEYS TO CENTER THE RASTER ON THE GREEN, RED AND BLUE CRT RESPECTIVELY <ENTER> to continue <EXIT>... -
Page 31: Crt Projection Angle Adjustment
CRT PROJECTION ANGLE ADJUSTMENT CRT PROJECTION ANGLE IS THE FIRST STEP OF STATIC CONVERGENCE ADJUSTMENT. IT IS CRITICAL THAT THE RASTERS ARE CENTERED ON THE CRT FACE PLATES PRIOR TO PERFORMING THIS STEP. <ENTER> to read more <EXIT> to return CRT PROJECTION ANGLE ADJUSTMENT DURING THIS PROCEDURE,... - Page 32 PROJECTION ANGLE ADJUSTMENT Align crosshairs <ENTER> continue <EXIT> to return (SW1 > SW2)
- Page 33 DIAGONAL IMAGE FOCUSING 1. TURN THE SCREW MARKED Ã TO FOCUS THE IMAGE DIAGO- NALLY from LEFT (bottom) TO RIGHT (top). 2. TURN THE SCREW MARKED TO FOCUS THE IMAGE DIAGO- NALLY from LEFT (top) TO RIGHT (bottom) <ENTER> to continue <EXIT>...
-
Page 34: Blue Image
LENS CORNER FOCUSING CENTER FOCUSING DIAGONAL IMAGE FOCUSING DIAGONAL IMAGE FOCUSING from left top to right bottom from left bottom to right top i ‚ y‡Ã6 % i ‚ y‡Ã6 i ‚ y‡Ã6 # i ‚ y‡Ã6 " i ‚ y‡Ã6 ! i ‚... - Page 37 Use the potentiometers on the G2-ADJ. module to set the screen grid voltage for Red, Green and Blue. Adjust until the LED on the corresponding output amplifier is turned off. <EXIT> to return...
- Page 38 é ê ç è é ê ç è é ê...
- Page 39 é ê ç è é ê ç è é ê é ê ç è é ê ç è é ê...