Use the parts list included in this manual to verify that all parts are accounted for before assembly. If any parts are missing, contact the retailer of this home gym for replacement parts. Or, call Inspire at 714-738-1729 Service of your home gym should only be preformed by an authorized INSPIRE retailer.
PARTS & HARDWARE LIST Item Parts Description Item Hardware Description Rec'd Rec'd Leg Press Base Bolt, 3/8-16 x 1" L Button Head Press Arm, Left Bolt, 3/8-16 x 1" L Press Arm, Right Bolt, 3/8-16 x 1 1/4" L Foot Plate Bolt, 3/8-16 x 1 3/4"...
CABLE CHART LP2 Main Cable LP2-M4 Attachment Cable Page 4...
Page 7
Assembly Instructions Leg Press 2 Assembly Procedures for attaching LP2 to Home Gym Refer to page 6 if attaching to M1 & M2 Refer to page 9 if attaching to M3 Refer to page 12 if attaching to M4 Page 5...
Assembly Procedure for attaching Leg Press 2 to M1 & M2 NOTE: The Leg Press may be attached to either side of the Home Gym. The Illustrations show only one side. Lower Cable STEP 1 Disconnect Cable & Remove Pulley 1 Step 1: Remove Pulley 1 and disconnect Lower Cable from Home Gym.
Assembly Procedure for Attaching Leg Press 2 to M3 NOTE: The Leg Press may be attached to either side of the Home Gym. The Illustrations show only one side. STEP 3 Disconnect Middle Cable STEP 2 Middle Cable Remove Pulley 1 & 1” Barrel Spacer from M3 Base Frame Pulley 1 &...
Assembly Procedure for Attaching Leg Press 2 to M4 NOTE: The Leg Press can only be attached to the right side of the Home Gym. STEP 1 Floating Pulley Bracket Step 1: Disconnect Floating Pulley Bracket from Main Upright and save removed hardware. Page 12...
Page 15
STEP 3 2 – 5” Hex Bolts 1 – 4 ¾” Hex Bolt 4 – 3/8” Flat Washers 1 – 3/8” Flat Washer 2 – 3/8” Lock Nuts Use Upper Holes Leg Press Attachment Arm STEP 2 Home Gym 2 – 1 ¼” Hex Bolts Leg Press Base 4 –...
STEP 8 Orthopedic Pad Seat Base Assembled Back & Seat Pad Step 8: Place Orthopedic Pad on Seat Base. Work the edge of pad into the groove of the Seat base on all sides. Do not use sharp objects during installation.
Page 20
STEP 11 Back Pad Stem 2 – 1” Hex Bolts 2 – 3/8” Flat Washers STEP 10 2 – 2 ½” Hex Bolts 4 – 3/8” Flat Washers 2 – 3/8” Lock Nuts Back Pad Handles Seat Pad STEP 12 To these sets of holes Attach Seat &...
Page 21
3/8” Barrel Spacer STEP 14 4 – 3/8” Barrel Spacers 4 – 1” Button Head Bolts 4 – 3/8” Small OD Washers 4 – 3/8” Thin Lock Nuts STEP 13 Rubber Bumper Pads Foot Plates STEP 15 Press Arms Step 13: Install Two Adjustable Bumpers. Step 14: Attach Foot Plates to Press Arms with Rubber Bumper Pads towards top as follows, tighten bolts first, then install and tighten Thin Lock Nuts using: Four (3/8”...
Page 22
Adjustable Bumpers Locking Rod Storage STEP 16 Step 16: Slide Locking Rod thru both Press Arm Brackets and tighten Adjustable Bumpers against Locking Rod to secure Locking Rod in place. Store Locking Rod in Leg Press Base as shown when not in use. Page 20...
GENERAL MAINTENANCE INFORMATION Warning: DO NOT place styrofoam or printed materials on the orthopedic seat pads. Over time, these may stick to the pads and mar the surface. Do not leave items sitting on the orthopedic seat pads, these pads have a special density that takes shape to objects and small objects will leave imprints in the surface that may take time to come out.
MAINTENANCE SCHEDULE HOME ROUTINE ENTRY DATE MAINTENANCE WEEKLY Clean: Seat Pads Inspect: Cables and WEEKLY their Fittings 3 MONTHS Inspect: All Decals Inspect: All Nuts and 3 MONTHS Bolts. Tighten if Needed Lubricate: Seat Sleeves 3 MONTHS and all Plastic Slides Clean and Wax: All YEARLY Glossy Finishes...
LIMITED WARRANTY In-Home Lifetime Warranty. This Warranty applies only in the United States to Inspire strength products manufactured or distributed by Health In Motion LLC. The warranty period to the original purchaser is lifetime of the original purchaser. Health In Motion warrants that the Product you have purchased for non-commercial, personal, family or household use from Health In Motion LLC or from an authorized Health In Motion reseller is free from defects in materials or workmanship under normal use during the warranty period.