Grandstream Networks GXW410x User Manual page 19

SIP Settings
SIP Registration
Unregister on Reboot
Register Expiration
SIP Registration Failure
Retry Wait Time
SIP Transport
Session Expiration
Min-SE
Caller Request Timer
Callee Request Timer
Force Timer
UAC Specify Refresher
UAS Specify Refresher
Force INVITE
Enable 100rel
Refer-to uses Target
Contact
INVITE Ring-no-answer
Timeout
Accept INVITE from Proxy
Only
Audio Settings
Preferred Vocoder
Call Settings
User ID is Phone Number
Early Dial
Grandstream Networks, Inc.
Firmware Version 1.4.1.5
This parameter controls whether the GXW410x needs to send REGISTER messages
to the SIP Server. The default setting is "Yes".
Default is No. If set to yes, the SIP user's registration information will be cleared on
reboot.
This parameter allows the user to specify the time frequency (in minutes) for the
GXW410x to refresh its registration with the specified registrar. The default interval is
60 minutes (or 1 hour). The maximum interval is 65535 minutes (about 45 days).
This parameter is mostly used by Service Providers. It prevents message REGISTER
overload of SIP Server in case of downtime due to maintenance or power failure. By
increasing interval length, common message load is decreased. Interval range is 1 –
3600 seconds.
User can select UDP or TCP. Please make sure you're SIP Server or network
environment supports SIP over the selected transport method. Default is UDP.
Grandstream implemented SIP Session Timer. The session timer extension enables
SIP sessions to be periodically "refreshed" via a SIP request (UPDATE, or re-INVITE.
Once the session interval expires, if there is no refresh via a UPDATE or re-INVITE
message, the session will be terminated. Session Expiration is the time (in seconds)
at which the session is considered timed out, if no successful session refresh
transaction occurs beforehand. The default value is 180 seconds.
The minimum session expiration (in seconds). The default value is 90 seconds.
If selecting "Yes" the phone will use session timer when it makes outbound calls if
remote party supports session timer.
If selecting "Yes" the phone will use session timer when it receives inbound calls with
session timer request.
If selecting "Yes" the phone will use session timer even if the remote party does not
support this feature. Selecting "No" will allow the phone to enable session timer only
when the remote party support this feature. To turn off Session Timer, select "No" for
Caller Request Timer, Callee Request Timer, and Force Timer.
As a Caller, select UAC to use the phone as the refresher, or UAS to use the Callee
or proxy server as the refresher.
As a Callee, select UAC to use caller or proxy server as the refresher, or UAS to use
the phone as the refresher.
Session Timer can be refreshed using INVITE method or UPDATE method. Select
"Yes" to use INVITE method to refresh the session timer.
The use of the PRACK (Provisional Acknowledgment) method enables reliability to be
offered to SIP provisional responses (1xx series). This is very important if PSTN inter-
networking is to be supported. A user's request to use reliable provisional responses
is invoked by the 100rel tag which is appended to the value of the required header of
initial signalling messages.
Default is NO. If set to YES, then for Attended Transfer, the "Refer-To" header uses
the transferred target's Contact header information.
In case incoming call has arrived from PSTN to VoIP and INVITE message was
generated by GXW device, the call will be disconnected after preconfigured timeout if
not answered by VoIP extension.
Default is YES. The device will authenticate and accept only incoming INVITE
messages from the peered SIP server.
The GXW410x supports up to 5 different Vocoder types including G.711 A-/U-law,
GSM, G.723.1, G.729A/B. The user can configure Vocoders in a preference list that
will be included with the same preference order in SDP message. The first Vocoder in
this list can be entered by choosing the appropriate option in "Choice 1". Similarly, the
last Vocoder in this list can be entered by choosing the appropriate option in "Choice
8".
If the GXW410x has an assigned PSTN telephone number, this field should be set to
"Yes". Otherwise, set it to "No". If "Yes" is set, a "user=phone" parameter will be
attached to the "From" header in SIP request.
Default is No. Use only if proxy supports 484 response.
GXW410x User Manual Page 19 of 32
Last Updated: 5/2014