Settings; Table 8: Settings Definitions - Grandstream Networks GXW410x User Manual

Layer 2 QoS
Video Surveillance (HW
version 1 only)
Date & Time
NTP server
Allow DHCP Option 42 to
override an NTP server
Self-Defined Time Zone
(Yes/No)
Optional Rule:

SETTINGS

General settings
Use NAT IP
STUN Server
Call Settings
G723 Rate
Voice Frames per Tx
Grandstream Networks, Inc.
Firmware Version 1.4.1.5
This contains the value used for layer 2 VLAN tag.
802.1q / VLAN tag: Default value is 0. Range lies from 0 to 4095.
802.1p Priority value: Default value is 0. Range lies from 0 to 7.
*** The above 2 settings need to be supported on the network and then configured
accordingly on the GXW410x. Incorrect configuration will cause blocked access,
which will result in Factory Reset as the only option to renew access.
Default is No. Set to Yes, in order to enable the video in port. And configure the RTSP
port number here(default port number 554).
URI or IP address of the NTP (Network Time Protocol) server, which will be used by
the phone to synchronize the date and time.
Default value is No. If set to Yes, the NTP server will originate from the DHCP server.
This parameter controls whether the displayed time will be daylight savings time or
not. If set to "Yes" and the Optional Rule is empty, then the displayed time will be 1
hour ahead of normal time. The "Automatic Daylight Saving Time Rule" shall have the
following syntax: start-time;end-time;saving
Both start-time and end-time have the same syntax:
Month ,day ,weekday ,hour ,minute
month: 1,2,3,..,12 (for Jan, Feb, .., Dec)
day: [+|-]1,2,3,..,31
weekday: 1, 2, 3, .., 7 (for Mon, Tue, .., Sun), or 0 which means the daylight saving
rule is not based on week days but based on the day of the month.
hour: hour (0-23),
minute: minute (0-59)
If "weekday" is 0, it means the date to start or end daylight saving is at exactly the
given date. In that case, the "day" value must not be negative.
If "weekday" is not zero and "day" is positive, then the daylight saving starts on the
first "day"th iteration of the weekday (1st Sunday, 3rd Tuesday etc). If "weekday" us
not zero and "day" is negative, then the daylight saving starts on the last "day"th
iteration of the weekday (last Sunday, 3rd last Tuesday etc). The saving is in the unit
of minutes. The saving time may also be preceded by a negative (-) sign if subtraction
is desired instead of addition. The default value for "Automatic Daylight Saving Time
Rule" shall be set to
"03,11,0,02,00;11,04,0,02,00;60" which is the rule for US.
Examples:
US where daylight saving time is applicable: 03,11,0,02,00;11,4,0,02,00;60
This means the daylight saving time starts from 11
November 4th at 2AM. The saving is 60 minutes (1hour).

TABLE 8: SETTINGS DEFINITIONS

NAT IP address used in SIP/SDP message. Default is blank.
IP address or Domain name of the STUN (Simple Traversal of UDP through NATs)
server.
G723 encoding rate (6.3kbps or 5.3kbps)
This field contains the number of voice frames to be transmitted in a single packet.
When setting this value, the user should be aware of the requested packet time (used
in SDP message) as a result of configuring this parameter. This parameter is
associated with the first vocoder in the above vocoder Preference List or the actual
GXW410x User Manual
th
March at 2AM and ends
Page 16 of 32
Last Updated: 5/2014