Electrical Connections - King Industrial KC-122FC Instruction Manual

ALL ELECTRICAL CONNECTIONS MUST BE DONE BY A QUALIFIED ELECTRICIAN. FAILURE TO COMPLY MAY RESULT IN
SERIOUS INJURY! ALL ADJUSTMENTS OR REPAIRS MUST BE DONE WITH THE DRILL PRESS DISCONNECTED FROM THE POWER
SOURCE. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY!
POWER SUPPLY
WARNING: YOUR DRILL PRESS MUST BE CONNECTED TO A
110V, 15-AMP, BRANCH CIRCUIT AND USE A 15-AMP TIME
DELAY FUSE OR CIRCUIT BREAKER. FAILURE TO CONNECT IN
THIS WAY CAN RESULT IN INJURY FROM SHOCK OR FIRE.
Your drill press must be properly grounded. Not all outlets are
properly grounded. If you are not sure if your outlet is properly
grounded, have it checked by a qualified electrician.
WARNING: IF NOT PROPERLY GROUNDED, THIS DRILL PRESS
CAN CAUSE ELECTRICAL SHOCK, PARTICULARLY WHEN
USED IN DAMP LOCATIONS. TO AVOID SHOCK OR FIRE, IF THE
POWER CORD IS WORN OR DAMAGED IN ANY WAY, HAVE IT
REPLACED IMMEDIATELY.
GROUNDING
This drill press must be grounded. If it should malfunction or
breakdown, grounding provides a path of least resistance for electric
current, to reduce the risk of electric shock. This drill press is
equipped with a cord having an equipment-grounding conductor
and grounding plug. The plug must be plugged into an appropriate
outlet that is properly installed and grounded in accordance with all
local codes and ordinances.
WARNING: TO MAINTAIN PROPER GROUNDING OF YOUR
DRILL PRESS, DO NOT REMOVE OR ALTER THE GROUNDING
PRONG IN ANY MANNER.
110V OPERATION
As received from the factory, your drill press is ready to run for 110V
operation. This drill press is intended for use on a circuit that has an
outlet and a plug which looks like the one illustrated in Fig.2.
WARNING: DO NOT USE TWO-PRONG ADAPTORS FOR THEY
ARE NOT IN ACCORDANCE WITH LOCAL CODES AND
ORDINANCES. NEVER USE IN CANADA.
220V OPERATION
If 220V, single phase operation is desired, the following instructions
must be followed:
1. Disconnect the machine from its power source.
2. The drill press comes with four motor leads that are connected for
110V operation. Reconnect these four motor leads for 220V
operation, as indicated on the inside of the capacitor cover.
3. The 110V plug supplied with the drill press must be replaced with a
CSA listed plug suitable for 220V operation. This plug is illustrated
in Fig.3. Contact your authorized service center or qualified
electrician to install the plug and to change the connections from
110V to 220V. The drill press must comply with all local and
national codes after the 220V plug is installed.
4. A drill press with a 220V plug should only be connected to an outlet
having the same configuration as illustrated by the grounded outlet
box in Fig.2. No adaptor is available or should be used for
220V operation.

ELECTRICAL CONNECTIONS

WARNING
EXTENSION CORDS
The use of any extension cord will cause some loss of power. Use
the following table to determine the minimum wire size (A.W.G-
American Wire Gauge) extension cord. Use only 3-wire
extension cords which have 3-prong grounding type plugs and
3-hole receptacles which accept the tool's plug.
For circuits that are further away from the electrical circuit box, the
wire size must be increased proportionately in order to deliver
ample voltage to the dust collector motor. Refer to Fig.4 for wire
length and size.
PROPERLY GROUNDED OUTLET
CURRENT CARRYING
PRONGS
GROUNDING
PRONG
FIGURE 2
PROPERLY GROUNDED OUTLET
CURRENT CARRYING PRONGS
GROUNDING PRONG
FIGURE 3
LENGTH OF
CONDUCTOR
0-25 FEET
26-50 FEET
51-100 FEET
FIGURE 4
WIRE SIZES REQUIRED
(AMERICAN WIRE GAUGE)
110V LINES
NO.16
NO.14
NO.12