King Industrial KC-6HJC Instruction Manual

King Industrial KC-6HJC Instruction Manual

6” benchtop jointer with helical cutterhead

Advertisement

6" BENCHTOP JOINTER WITH
HELICAL CUTTERHEAD
08/2016

INSTRUCTION MANUAL

MODEL: KC-6HJC
COPYRIGHT © 2016 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.

Advertisement

Table of Contents
loading

Summary of Contents for King Industrial KC-6HJC

  • Page 1: Instruction Manual

    6” BENCHTOP JOINTER WITH HELICAL CUTTERHEAD 08/2016 INSTRUCTION MANUAL MODEL: KC-6HJC COPYRIGHT © 2016 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
  • Page 2: Warranty Information

    WARRANTY INFORMATION 2-YEAR kING CANADA TOOLS LIMITED WARRANTY OFFERS A 2-YEAR LIMITED WARRANTY FOR THIS 6” BENCHTOP JOINTER INTENDED FOR NON COMMERCIAL USE PROOF OF PURCHASE Please keep your dated proof of purchase for warranty and servicing purposes. REPLACEMENT PARTS Replacement parts for this product are available at our authorized King Canada service centres across Canada.
  • Page 3 GENERAL & SPECIFIC SAFETY RULES 1. kNOW YOUR TOOL watch) because they could get caught in moving parts. Non-slip Read and understand the owners manual and labels affixed to the footwear is recommended. Wear protective hair covering to contain tool. Learn its application and limitations as well as its specific po- long hair.
  • Page 4 12) Fence support arm 5) Cutterhead guard 13) Fence mounting bracket 6) Depth of cut pointer 14) Belt guard 7) Safety switch Specifications MODEL KC-6HJC Capacity 6” Depth of cut capacity 1/8” Cutterhead speed 12,000 RPM Table size 6-1/8” x 29-7/8”...
  • Page 5: Electrical Information

    ELECTRICAL INFORMATION WARNING! ALL ELECTRICAL CONNECTIONS MUST BE DONE BY A QUALIFIED ELECTRICIAN. FAILURE TO COMPLY MAY RESULT IN SE- RIOUS INJURY! ALL ADJUSTMENTS OR REPAIRS MUST BE DONE WITH THE MACHINE DISCONNECTED FROM THE POWER SOURCE. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY! POWER SUPPLY PROPERLY GROUNDED OUTLET WARNING: YOUR JOINTER MUST BE CONNECTED TO A 110V-120V, 15-...
  • Page 6 ASSEMBLY WARNING! TO REDUCE THE POTENTIAL FOR PERSONAL INJURY AND/OR DAMAGE TO THE MACHINE, BEFORE ASSEMBLING MAKE SURE THE MA- CHINE IS TURNED OFF AND THE PLUG IS NOT CONNECTED TO A POWER SOURCE. DO NOT TURN ON OR PLUG IN THE MACHINE UNTIL INSTRUCTED TO DO SO AFTER ALL ASSEMBLY STEPS IN THIS MANUAL HAVE BEEN COM- PLETED.
  • Page 7: Operation & Adjustments

    OPERATION & ADJUSTMENTS Fence Adjustments - Front to Back The fence can be moved across the table to expose as much or as little of the cutterhead as needed depending on the width of the workpiece. 1) Loosen the fence adjustment lock handle (A) Fig.8 by turning handle counter- clockwise.
  • Page 8 OPERATION & ADJUSTMENTS Infeed Table Height/Depth of Cut Adjustment Note: The outfeed table is factory-set to the height of the cutterhead inserts and unless it becomes misaligned, it requires no regular adjustments. The infeed table height is adjustable and can be raised or lowered to set the depth of cut.
  • Page 9: Operation And Maintenance

    OPERATION & MAINTENANCE WARNING! TO REDUCE THE POTENTIAL FOR PERSONAL INJURY KEEP HANDS WELL AWAY FROM THE CUTTERHEAD DURING JOINT- ING OPERATIONS - USE PUSH BLOCKS WHENEVER POSSIBLE. Face Jointing 1) Set the infeed table height for the desired depth of cut. Note: 1/16” to 1/32” is recommended depending on the width of the board. 2) Set and lock the fence at 90º.
  • Page 10: Maintenance

    MAINTENANCE WARNING! TO REDUCE THE POTENTIAL FOR PERSONAL INJURY MAKE SURE THE MACHINE IS TURNED OFF AND HAS BEEN UNPLUGGED BEFORE PERFORMING ANY PERIODIC MAINTENANCE OPERATIONS. Periodic Maintenance as Required Over time with use and wear some or all of the following periodic maintenance op- erations may be required: Replacing/Rotating Cutterhead Inserts The cutterhead is equipped with 12 cutter inserts with 2 cutting surfaces each.

Table of Contents