Sony HDW-790 Operation Manual page 83

c Color temperature
This indicates the currently selected color temperature.
d UHF wireless microphone reception level
This indicates the reception level of the wireless
microphone when the UHF wireless microphone is
attached, using four x which appear at the right of "W."
When all four x are lit, the reception is good.
e DC IN / battery voltage or remaining capacity
This shows the battery voltage or remaining capacity of an
internal battery pack.
When the power is supplied from an AC adaptor connected
to the DC IN connector, "DC IN" appears.
When the DISP BATT REMAIN item is set to "INT" or
"AUTO" on the VF DISP 2 page of the USER menu, the
remaining battery capacity is automatically detected and
indicated as a percentage when the Anton Bauer intelligent
battery system or the BP-GL65/GL95 battery pack is used.
The indicated value changes in steps of 10%.
• Until the remaining battery capacity is reduced to 40%,
the indications MAX, 90%, 80%...40% are displayed for
3 seconds in the viewfinder each time the remaining
battery capacity reduces by 10%.
• When the remaining battery capacity is less than 40%,
the indication is displayed all the time.
• When the remaining battery capacity is less than 10%
the indication flashes. When the remaining battery
capacity is reduced further, the LOW indication flashes.
1) When the DISP BATT REMAIN item is set to "AUTO," the remaining
capacity of the battery is displayed all the time.
When VOLT is selected, or even when AUTO is selected, if the remaining
battery capacity cannot be detected is used, the battery voltage is
displayed.
2) This value can be set to either 10% or 20% on the FUNCTION 2 page of
the OPERATION menu.
f * indicator
This flashes when the color bars are displayed and is
recorded together with the color bars.
g Setting change and adjustment progress message
display area
For details, see "5-2-3 Display Modes and Setting Change
Confirmation/Adjustment Progress Messages" on page 85.
h Operation/error message display area
For details, see "Operation/error messages" on page 140.
i Iris setting/auto iris override
This indicates the f-stop (iris setting) of the lens.
Also, the auto iris override is displayed using bars which
appear in the upper and lower parts of the screen, to the left
of the F number respectively.
For details, see "4-3 Changing the Reference Value for
Automatic Iris Adjustment" on page 66.
1)
2)
,
j Remaining tape
This indicator indicates the remaining tape recording time
(in minutes) of the VTR.
Examples of remaining tape recording time indication
Indication Remaining tape recording time
F – 30 Full to 30 minutes
30 – 25 30 to 25 minutes
25 – 20 25 to 20 minutes
20 – 15 20 to 15 minutes
15 – 10 15 to 10 minutes
10 – 5 10 to 5 minutes
5 – 0 5 to 2 minutes
5 – 0 (flashing) 2 to 0 minutes
k Audio level
These items indicate the level of audio channel 1 and
channel 2. The peak indication of the VTR level meter is
related as follows to the audio level when a 1-kHz sine
wave is input.
Audio channel 1
level indicator
Audio channel 2
level indicator
VTR level meter
indicator
l Shutter speed
This indicates the shutter speed or the shutter mode.
However, if the SHUTTER selector is set to OFF, nothing
is displayed.
1/100, 1/125, 1/250, 1/500, 1/1000, 1/2000: Shutter speed
(in seconds) in standard mode
ECS: ECS mode
EVS: EVS mode
1F to 8F, 16F, 32F, 64F: Number of frames in SLS mode
1) The SLS mode is effective only when an optional HKDW-905R extension
board is installed.
m Gain
This indicates the gain of the video amplifier, as set by the
GAIN selector.
n White balance memory
This indicates the currently selected white balance
automatic adjustment memory.
A: Displayed when the WHITE BAL switch is set to A.
B: Displayed when the WHITE BAL switch is set to B.
P: Displayed when the WHITE BAL switch is set to PRST.
T: Displayed when ATW is being used.
When an optional RM-B150/B750 Remote Control Unit is
connected, you can switch the memory using the switch on
the RM-B150/B750.
Status Display on the Viewfinder Screen
1)
83