Page 1
Schaerer Siena 1 / 2 V04 08.2007 Bedienungsanleitung, Seite 2 User manual, Page 35 Manuel d'utilisation, Page 69 Gebruiksaanwijzing, Pagina 103 Manual del usuario, Página 137 Návod k obsluze, Strana 171 Használati útmutató, Oldalt 205 SWISSMADE www.schaerer.com...
All of the information, technical data, pictures and illustrations used in this manual are based on the most current data available at the time of printing. Your machine may vary from those shown in the pictures (options). The company M. Schaerer Ltd.
Page 3
Bean container (with lid) Insert for coffee powder (cleaning tablet) Cup plate Service door Control panel (2 parts) (see below) Brew unit Siena 1: Rotary dial Steam / hot water Grounds container Siena 1: Milk tube Hot water / steam...
Introduction Safety symbols Observe the safety instructions on page 40! Exercise extreme caution when these Caution! Caution! symbols appear! Risk of damage to User at risk! machine! Caution! Caution! Hot fluid! Hot steam! Caution! Caution! Hot surface! Risk of squeezing!
Safety notes General At M. Schaerer AG, the highest degree of safety is one of the most important product features. The effectiveness of the safety devices is guaranteed only if the following instructions are ob- served to prevent injuries and health hazards: •...
Safety notes Disposal! For safety reasons, machines that have reached the end of their product life cycles must be rendered unusable. To do so, disconnect the power cord and sever the connector cable. After- ward, dispose of the device in accordance with regulations.
„General terms and conditions“ of M. Schaerer AG and this User Manual. In legal terms, any other use is not an intended use. The manufacturer accepts no liability for damage resulting from unintended use.
Product description Product description Overview - machine (Refer to page 36) Overview - control panel (Refer to page 36) Detailed picture of the foamer head (Siena 2) 1. Foamer head 2. Corner p 3. Foam nozzle If no milk foam is dispensed, insert the supplied instrument (air valve pin) into the foam nozzle [ 3 ].
Product description Water connection / draining (option) The water supply connection must be made in accordance with the applicable requirements and the regulations of the respective country. If the machine is connected to a newly installed water pipe, the pipe and the supply tube must be thoroughly rinsed so that no dirt particles can enter the machine.
Operation Commissioning Before using for the first time: Never operate the device without water. After longer periods of non-use (e.g. due to holiday), it is recommended for hygienic reasons that the device be rinsed by means of the hot water/steam injector and the cleaning program started before the device is used again.
Operation Operation Introduction This chapter describes the basic functions of the coffee machine. Observe these instructions in order to ensure smooth and safe daily operation. Please observe the safety notes on page 40! Correct and optimal operation of the coffee machine is required and ensured through proper installation and programming by a qualified service technician.
Operation Operating modes The Siena 1 / 2 has two (2) operating modes: << Stand by >> << Stand by >> The machine is switched off but still connected to the power supply. The following message appears on the display (shown left).
Operation Preparing hot water (Siena 2) The temperature indicator lights up in green. ► Place a cup under the hot water outlet. ► Press the button. The dispensing procedure is stopped by pressing the button again. ► Remove the cup from under the outlet.
Operation Preparing milk foam (Siena 2) Milk foam can be dispensed and/or added at any time. ► Place a cup under the outlet. ► Press the button and keep it pressed. ► Press and hold the cappuccino/macchiato button to dispense milk foam. „Milk“ appears on the display.
Programming Programming Your coffee machine is pre-programmed at the factory. You also have the option, however, of adjusting the device to your individual tastes. You can program the following product-related elements (refer also to the programming overview): Water volume - coffee quantity - pre-brew function In addition, you can program various device functions individually.
Programming Overview: programming common parameters Accessing the programming level: Bereit ► Press to access the programming level. Product, 2x, C Press the button English ► Set the language using ► Confirm by pressing bestätigen. Temp. 86 °C ► Set the brewing temperature using ►...
Programming Overview: programming fixed parameters Accessing the programming level: Ready ► Press to access the programming level.. Product, 2x, C Press the button Code #### ► Set each digit using ► Confirm by pressing Counter status? ► Set counter level to 0 using (if desired).
Cleaning Cleaning his chapter describes the cleaning of the coffee machine. To achieve the best possible quality of the dispensed beverages, it is necessary to clean the machine properly and thoroughly on a daily and weekly basis. Please observe the safety notes on page 41! •...
Cleaning Daily and weekly cleaning Carefully read the information given in the user manual as it contains important information regarding safety,hygiene, use and maintenance of the machine. Never reach into the machine or under the beverage outlets during the automatic cleaning!
Cleaning Coffee system cleaning: Milk system rinsing: (Siena 1 / Siena 2) (Siena 2) ► Fill the water tank with fresh water. ► Insert the cleaning tablet into the funnel. ► Put the milk tube into a container with ►...
Cleaning Descaling Carefully read the information given in the user manual as it contains important information regarding safety, hygiene, use and maintenance of the machine. Never reach into the machine or under the beverage outlets during the descaling process! Never interrupt the descaling proc-...
Cleaning When the descaling is finished, a prompt to carry out the daily cleaning appears automatically. ► Descaling process is finished. On the display appears: << Stand by >> ► Reinstall the outlet. Installing/detaching the foam head (Siena 2) Press the front of the foam head [ 1 ].
Troubleshooting Troubleshooting Before having the machine repaired, please check the following points: Malfunctions and possible causes Fault Cause/remedy ► The power plug is not properly connected Does the coffee machine not ► The main power switch (on the left-hand side) is not set to...
Troubleshooting Service and maintenance work Even if the coffee machine is cleaned and maintained in an ideal manner, it must be serviced (once a year). Having a qualified service technician inspect the coffee machine regularly ex- tends its product life cycle.
Appendix Options Coin tester The following accounting systems are available: • Tokens • Coins The coin tester option is possible in country-specific currencies. Please contact your customer service representative for further information. Coin tester - operation and maintenance Amount 1.20...
EC low-voltage directive 2004/108/EC EC Directive, Electromagnetic Compatibility Information about the declaration of conformity can be obtained from the manufacturer upon request: Manufacturer: M. Schaerer AG Gewerbestrasse 15 3302 Moosseedorf Switzerland info@schaerer.com www.schaerer.com For more information please contact your local dealer!
Appendix Cleaning products IBEDA cleaning tablet (Art.-No.: 062867) Before using the cleaning tablet, please read the information on the tablet‘s packaging as well as the safety data sheet („HEALTH & SAFETY DATA SHEET“). If you do not have this safety data sheet, please request it from your sales centre.
Appendix Emergency information: Please ask your sales centre or a cucological information centre) in your country. If your country does not have any such institution, dial the following telephone number in Switzerland in an emer- gency or for information: ++41 01 251 51 51 (Toxicological Information Centre) www.toxi.ch (DE / UK / FR)
Need help?
Do you have a question about the Siena 1/2 and is the answer not in the manual?
Questions and answers