Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Norton CST 65 Modulo
Summary of Contents for Norton CST 65 Modulo
- Page 1 CST 65 / 85 / 100 MODULO OPERATING INSTRUCTIONS...
-
Page 3: Declaration Of Conformity
Declaration of conformity The undersigned manufacturer: SAINT - GOBAIN ABRASIVES S.A. 190, BD J.F. KENNEDY L- 4930 BASCHARAGE Declares that this product: CST 65 Modulo 230V 70184620265 Masonry Saws: Code: CST 85 Modulo 230V 70184620266 CST 100 Modulo 230V 70184620024 is in conformity with the following Directives: •... -
Page 5: Table Of Contents
OPERATING INSTRUCTIONS AND SPARE PARTS LIST Basic Safety Instructions Symbols 1.2 Machine plate Safety instructions for particular operating phases Machine description Short description Purpose of use Layout Technical Data Assembly and commissioning Tool assembly Handle assembly Electrical connections Starting the machine Water cooling system Transport and storing Securing for transport... -
Page 6: Basic Safety Instructions
1 Basic Safety Instructions The CST is exclusively designed for the cutting of construction products mainly on construction sites. Uses other than the manufacturer's instructions shall be considered as contravening the regulations. The manufacturer shall not be held responsible for any resulting damage. Any risk shall be borne entirely by the user. -
Page 7: Machine Plate
1.2 Machine plate Important data can be found on the following plate located on the machine: Year of production Maximum blade diameter Machine Model Machine Code Weight Bore diameter Machine type Serial number Power Safety standard Blade speed 1.3 Safety instructions for particular operating phases Before commencing work •... -
Page 8: Machine Description
2 Machine description Any modification, which could lead to a change in the original characteristics of the machine, may be done only by Saint-Gobain Abrasives who shall confirm that the machine is still in conformity with the safety regulations. 2.1 Short description The CST block saw is designed for durability and high performance for onsite wet and dry cutting operations of a wide range of masonry, refractory and natural stone products. - Page 9 Frame (2) Built in aluminium profile, the frame is light and resistant. The welded-steel side of the machine ensure that the axles are parallel to the table. The axle assembly can also be tilted until 45º to make bevel cuts. The head axles (3) made of aluminium, guide the cutting head over the table. The head consoles (4) ensure the parallelism of the two axles, and rigidity of the assembly.
-
Page 10: Technical Data
2.4 Technical Data Electric motor protection IP54 Max. blade diameter 350 mm Bore 25,4 mm Flange diameter 90 mm Cutting depth mm 110 mm (without reversing the material) Sound pressure level 73 dB (A) (following ISO EN 11201) Sound energy level 87 dB (A) (following ISO EN 3744) CST65 Code... - Page 11 CST100 Code 70184620024 70184620270 70184620273 Power 2,2 kW 2,2 kW 3 kW Tension 230V 1~ 115V 1~ 400V 3~ Cutting length 1000 mm Rotation speed of the blade 3000 min-1 Length 1680 mm Width 660 mm Height (with feet) 1550 mm Height (without feet) 905 mm Water pan capacity...
-
Page 12: Assembly And Commissioning
3 Assembly and commissioning The machine is delivered fully equipped (although without diamond blade) and is ready for operation after assembly of the blade and the handles, and connection to the appropriate power supply. 3.1 Tool assembly Only NORTON blades with a maximum diameter of 350 mm can be used with the CST. All tools used must be selected with regard to their maximum permitted cutting speed for the machine’s maximum permitted rotation speed. -
Page 13: Water Cooling System
3.5 Water cooling system Fill the water pan with clean water to approximately 2cm from top (ensure that bottom of pump is fully immersed in water). Use the pump switch so you can use the pump. Open water-tap at blade guard (note that handle on water-tap should be in line with water-flow). Ensure that water is flowing freely in the circuit and is delivered adequately to both sides of the blade, as insufficient water supply may result in premature failure of the diamond blade. -
Page 14: Transport And Storing
4 Transport and storing 4.1 Securing for transport Before transporting or lifting the machine, always remove the blade and empty the water pan. Also lock the cutting head on the axles. To do so, move the head so, that the screw (1) is facing the hole (2). -
Page 15: Operating The Machine
5 Operating the machine 5.1 Site of work 5.1.1 Siting the machine • Remove from the site anything, which might hinder the working procedure! • Make sure the site is sufficiently well lit! • Observe manufacturer's conditions for connecting to power supplies! •... -
Page 16: General Advice For The Cutting
5.3 General advice for the cutting • Material weighting under 30 kg and having dimensions smaller than 650x660x220mm for the CST65, 850x660x220mm for the CST85, 1000x660x220mm for the CST100 can be cut with the machine. • Before commencing work make sure tools are firmly seated! •... -
Page 17: Maintenance And Servicing
6 Maintenance and servicing To ensure a long-term quality from the cutting with the CST, please follow the maintenance plan below: Whole machine Visual control (general aspect, watertightness) Clean Flange and blade fixing devices Clean Motor cooling fans Clean Water pump Clean Water pan Clean... -
Page 18: Faults: Causes And Cures
Faults: causes and cures Fault-finding procedures Should any fault occur during the use of the machine, turn it off, and isolate it from the electrical supply. Any works dealing with the electrical system or supply of the machine can only be carried out by a qualified electrician. - Page 19 Circuit diagram 230V Motor...
- Page 20 115V Motor...
- Page 21 400V Motor...
-
Page 22: Customer Service
Spare parts for the motor can be ordered with the manufacturer of the motor or with their dealer, which is often quicker and cheaper. This machine has been manufactured by Saint-Gobain Abrasives S.A. Saint-Gobain Abrasives S.A. 190, Bd. J.F. Kennedy L- 4930 BASCHARAGE Grand-Duché... - Page 23 Guarantee can be claimed and technical support obtained from your local distributor where machines, spare parts and consumables can be ordered as well: Benelux and France: United Kingdom From Saint-Gobain Abrasives S.A. Saint-Gobain Abrasives Ltd. Free telephone numbers: Doxey Road...
- Page 24 SAINT-GOBAIN ABRASIVES 190, Bd. J. F. Kennedy L-4930 BASCHARAGE LUXEMBOURG Tel.: ++352 50401-1 Fax: ++352 501633 e-mail: sales.nlx@saint-gobain.com www.construction.norton.eu 29.09.2008...