Page 3
VERS. 07.06.2018 CM 450 Junior E_MAN_EN Declaration of conformity The undersigned manufacturer: SAINT - GOBAIN ABRASIVES S.A. 190, BD J.F. KENNEDY L- 4930 BASCHARAGE Declares that this product: CM 450 Junior 1-30-1 230V 70184608625 Masonry Saws: Code: is in conformity with the following Directives: ...
VERS. 07.06.2018 CM 450 Junior E_MAN_EN 1 BASIC SAFETY INSTRUCTIONS The CM 450 Junior is exclusively designed for the cutting of construction products mainly on construction sites. Uses other than the manufacturer's instructions shall be considered as contravening the regulations. The manufacturer shall not be held responsible for any resulting damage.
Always cut with the blade guard in position. Only fit NORTON diamond blades to the machine! The use of other tools can damage the machine! Read the blades’ specifications carefully to choose the correct tool for your application.
As with all other NORTON products, the operator will immediately appreciate the attention given to detail and quality of materials used in construction. The machine and its component parts are assembled to high standards assuring long life and minimum maintenance.
Page 9
VERS. 07.06.2018 CM 450 Junior E_MAN_EN Frame and feet (1) The frame is made of a jig-welded reinforced steel construction to ensure perfect rigidity. 4 removable legs fit into housings welded on frame sides and locked into place with locking screws. Cutting head (2) Spring loaded jig-welded steel console.
VERS. 07.06.2018 CM 450 Junior E_MAN_EN 2.4 Technical Data Electric motor 2,2 kW 230V with thermal overload protection Electric motor protection IP54 Max. blade diameter 450 mm Bore 25,4 mm Rotation speed of the blade 2100 min Flange diameter 95 mm Cutting depth mm 170 mm (without reversing the material) Sound pressure level...
VERS. 07.06.2018 CM 450 Junior E_MAN_EN 2.5 Statement regarding the vibration emission Declared value of vibration emission following EN 12096. Machine Measured value of vibration Uncertainty K Tool used Model / code emission at m/s Model / code CM 450 Junior 230V <2.5 Clipper ALFA...
VERS. 07.06.2018 CM 450 Junior E_MAN_EN 2.6 Statement regarding noise emission Declared value of noise emission following EN ISO 11201 and NF EN ISO 3744. Machine Sound Uncertainty K Sound power Uncertainty K Model / code Pressure level (Sound level (Sound power level Pressure level EN ISO 11201...
3.1 Tool assembly Only NORTON blades with a maximum diameter of 450 mm can be used with the CM 450 Junior. All tools used must be selected with regard to their maximum permitted cutting speed for the machine’s maximum permitted rotation speed.
VERS. 07.06.2018 CM 450 Junior E_MAN_EN 3.3 Electrical connections Check that, the voltage/phase supply corresponds to the information indicated on the motor plate. Available power supply must have ground connection in conformity with safety regulations. The connecting cables should have at least a 2.5mm -section per phase.
VERS. 07.06.2018 CM 450 Junior E_MAN_EN 4 TRANSPORT AND STORING 4.1 Securing for transport Before transporting the machine, always remove the blade and empty the water pan. Also remove the conveyor cart, as it can be dangerous while you move the machine. 4.2 Transport procedure Two people are necessary to move the machine.
VERS. 07.06.2018 CM 450 Junior E_MAN_EN 5 OPERATING THE MACHINE 5.1 Site of work 5.1.1 Siting the machine Remove from the site anything, which might hinder the working procedure! Make sure the site is sufficiently well lit! Observe manufacturer's conditions for connecting to power supplies! ...
Page 17
VERS. 07.06.2018 CM 450 Junior E_MAN_EN NOTE: While recommended, it is not absolutely necessary to lock the cutting head into a given depth position when jam cutting. The desired cutting depth can be maintained by holding firmly the depth feed handle on the blade guard. If the full depth of cut requires excessive pressure (on very dense material e.g.) make 2 or 3 shallow cuts.
VERS. 07.06.2018 CM 450 Junior E_MAN_EN 6 MAINTENANCE AND SERVICING To ensure a long-term quality from the cutting with the CM450, please follow the maintenance plan below: Whole machine Visual control (general aspect, watertightness) Clean Flange and blade fixing devices Clean Belts tension Check and adjust...
VERS. 07.06.2018 CM 450 Junior E_MAN_EN 7 FAULTS: CAUSES AND CURES Fault-finding procedures Should any fault occur during the use of the machine, turn it off, and isolate it from the electrical supply. Any works dealing with the electrical system or supply of the machine can only be carried out by a qualified electrician.
VERS. 07.06.2018 CM 450 Junior E_MAN_EN 7.4 Customer service When ordering spare parts, please mention: The serial number (seven digits). The code of the part. The exact denomination. The number of parts required. The delivery address. ...
VERS. 07.06.2018 CM 450 Junior E_MAN_EN Spare parts In order to consult the spare parts lists, we invite you to visit the after-sales website of Norton Clipper by using the following address: https://spareparts.nortonabrasives.com For a quick access, you can also use the QR Code shown below using your mobile phone: This electronic catalogue provides exploded views and spare parts lists for different machines designed by Norton Clipper so you can find references you need.
Page 23
VERS. 07.06.2018 CM 450 Junior E_MAN_EN...
Page 24
VERS. 07.06.2018 CM 450 Junior E_MAN_EN Guarantee can be claimed and technical support obtained from your local distributor where machines, spare parts and consumables can be ordered as well:...