Norton Clipper C1318P Owner's Manual
  1. Manuals
  2. Brands
  3. Norton Manuals
  4. Saw
  5. Clipper C1318P
  6. Owner's manual

Norton Clipper C1318P Owner's Manual

Small concrete saw
Hide thumbs Also See for Clipper C1318P:
Table of Contents

Advertisement

Quick Links

OWNERS
MANUAL
Small Concrete Saw
MODEL:
C1318P
FORM: C1318P rev 4-2017

Advertisement

Table of Contents
loading

Related Manuals for Norton Clipper C1318P

Summary of Contents for Norton Clipper C1318P

  • Page 1 OWNERS MANUAL Small Concrete Saw MODEL: C1318P FORM: C1318P rev 4-2017...
  • Page 2 In no event shall Norton be liable for consequential or incidental damages arising out of the failure of any product to operate properly. Integral units such as gasoline engines, electric motors, batteries, tires, transmissions, etc., are excluded from this warranty and are...

  • Page 3: Table Of Contents

    Blade Shaft Group 26-27 Belt Tensioning Group Engine Mount Group Main Frame Group Water Control Group 31-32 Front Pointer Group Read Owners Manual Before Use Safety Alert Symbol: Information Following This Symbol Is Very Important. Use Only Norton Diamond Blades...

  • Page 4: Preparation

    I. PREPARATION A. Safety Precautions Important! The following safety precautions must always be observed. Hazard Symbols Fuel (gasoline) is extremely flammable and its vapors can explode if ignited. Store gasoline only in approved containers, in well-ventilated, unoccupied approved areas, and away from sparks or flames.
  • Page 5 Dust and Silica Warning Grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as respiratory disease, cancer, birth defects or other reproductive harm. If you are unfamiliar with the risks associated with the particular process and/or material being cut or the composition of the tool being used, review the material safety data sheet and/or consult your employer, the material manufacturer/supplier, governmental agencies such as OSHA and...
  • Page 6 1. Before mounting any blade on the saw, the blade should be inspected for any damage which might have occurred during shipment, handling or previous use. 2. The blade collars and arbors should be cleaned and examined for damage before mounting the blade. 3.

  • Page 7: Assembly

    Inspect the saw for shipping damage. If any damage is found, contact the shipper immediately and file a freight claim. Norton Clipper is not responsible for any freight-related damages. Remove the saw from the pallet. Reverse the position of the handlebars so that the handle bar sticks out towards the operator.

  • Page 8: C1318P Series Concrete Saw Specifications

    C. C1318P Series Concrete Saw Specifications Dimensions/Weight Length (Working) 45.66” (1160 mm) Length (Transport) 33.50” (850 mm) Width 39.50” (1003 mm) Height 39” (990 mm) Weight 220 lbs (100 kg) Engine Engine Mfg. Honda Spec No. GX390K1QXC9 Engine Type Single Cylinder 4 Cycle Horse Power - Gross 13 hp* (9.5kW) @ 3,600 rpm Max Torque –...

  • Page 9: Pointer Alignment

    D. Engine Prior to attempting to operate the engine, read the information contained in the engine owner's manual. An engine owner’s manual is supplied with every gasoline powered concrete saw. 1. Check Oil: Add oil if low. Refer to the engine owner's manual for the recommended SAE viscosity grades.

  • Page 10: Starting The Engine

    4. Place the blade on the blade shaft, lining up the drive pin hole in the blade with the drive pinhole in the inside collar. For Best Performance Use Only Norton Diamond Blades Specified For the Material Being Cut. 5. Slide the outside blade shaft collar onto the blade shaft. The drive pin on the outside collar must project through the drive pin hole in the blade and into the inside collar.
  • Page 11 Move the choke lever to the CLOSED position. Turn the Fuel Control To the ON Position NOTE: do not use the choke if the engine is warm or the air temperature is high. Pull The Throttle Control Slightly to the Rear to Place the engine ON/OFF switch to the ON position provide some engine throttle.

  • Page 12: Water Supply

    C. Water Supply Pressurized source: Turn the water control to full "ON" when using wet cutting blades. The required flow rate is 4-6 gallons per minute. Water Tank on saw: This supply is designed for use with dry blades to keep the dust levels down.

  • Page 13: Cutting Technique

    10. When the end of the cut is reached, slowly raise the blade out of the cut by rotating the Hand Wheel counter-clockwise until the blade is at least one (1) inch above the ground. 11. Only move the saw in reverse with the blade in the raised position. 13.

  • Page 14: Maintenance

    Engine manual that came with the engine for any changes to the maintenance schedule. If the charts have any differences, follow the chart in the Honda Engine Manual. The Norton does not warranty the engine. If any warranty or service of the engine is required contact your nearest Honda service center, or from the Internet: http://www.honda-engines.com/home.htm...

  • Page 15: Bearings

    Always refer to the engine manual for more detailed information on checking the oil, changing oil, and oil capacity, air filter changes, and fuel type to use. Use only Honda air filters. Do not clean the air filter with gasoline or other flammable solvents.

  • Page 16: V-Belts

    For best results, bearings should be relubricated while in operation. Note: Due caution for personal safety must be observed when servicing rotating equipment. The grease should be pumped in slowly until a slight bead forms around the seals. This bead, in addition to acting as an indicator of adequate relubrication, provides additional protection against the entry of foreign matter.
  • Page 17 Engine M10 Mounting Bolt, Belt Guard qty =4. Note one (1) per corner of engine. Belt Tensioning Assembly M10 Belt Guard Retaining Hardware, qty=3. NOTE: One (1) Bolt is on the front of the Belt Guard Figure: C1318P Belt Tensioning System 1.
  • Page 18 Figure: C1318P Belt Tensioning Assembly 6. To apply tension to the Belts tighten (turn clockwise) the rear M10 Jam Nut until the required Belt Tension is achieved. To loosen the Belts turn the front M10 Jam Nut counter clockwise until the required Belt Tension is achieved.
  • Page 19 2. Remove the Belt Guard by loosening and removing the three M10 Belt Guard Retaining Bolts. 3. Line up a straight edge along the out side face of both pulleys. (See Figure: Pulley Alignment to the right.) 4. Misalignment will show up as a gap between the pulley face and the straight edge.

  • Page 20: Depth Control

    D. Depth Control The depth control (raising screw) consists of a threaded rod, which feeds into a steel nut. In order to keep the two parts working smoothly it is necessary to keep the rod free from dirt and sludge as much as possible. Cleaning the threaded rod with a rag after each use will prevent sludge from collecting in the tube assembly and protect the threads.

  • Page 21: Parts List Section

    Any wear due to normal use of the machine will not be considered as a case of warranty for items designated as Wear Parts (W). For best performance and life Genuine Norton Clipper replacement parts should always be used. Changes to part specifications,...

  • Page 22: Depth Control And Depth Lock Group

    Depth Control and Depth Lock Group Front Of Machine Item UPC No Part No Description Type NOTES 00310004840 076357 HANDWHEEL AND HANDLE Includes: Handle and Hardware 00310004966 076843 NUT HANDWHEEL Includes: Acorn Nut, and Washers 70184643370 SPACER 28x22x22 048620 00310327609 232349 WHEEL HOOK + SPRING CS 501 Includes: Hook, Spring, and Nut...

  • Page 23: Handle Bar Group

    Handle Bar Group Item UPC No Part No Description Type NOTES Includes: Handle Bar Frame (Upper 70184643284 HANDLE BAR ASSEMBLY C1318P and Lower), Hand Grips (2), Vibration 232313 Absorber Kit (4), and Hardware 00310004190 072097 GRIP HANDLE Sold As Each. Appearance May Vary 70184600809 SCR M10 X 25 8.8 DIN933 027021...

  • Page 24: Blade Guard Group

    Blade Guard Group Front Of Machine Item UPC No Part No Description Type NOTES Includes: Items 2 (2x), 3 (2x), 4 (2x), 5 70184643285 BLADE GUARD ASSEMBLY C1318P 232317 (2x), 6, 7. 8, and 9 70184628500 PIN GUARD LOCK 238222 70184628501 238223 RING GUARD LOCK...
  • Page 25 Blade Shaft Group Front Of Machine...

  • Page 26: Blade Shaft Group

    Blade Shaft Group Item UPC No Part No Description Type NOTES Includes: Pulley, Bushing, Set Screws, 70184643291 232352 PULLEY ENGINE KIT C1318P and Key 70184643371 232344 BELT POLY-V 10 PK 698MM Includes: Items 4, 5 (2x), 6, 7, 8, 9 70184643372 232357 SHAFT BLADE ASSEMBLY C1318P...

  • Page 27: Belt Tensioning Group

    Belt Tensioning Group Item UPC No Part No Description Type NOTES ENGINE MOUNTING KIT Includes: Front, Rear Motor Mounts, 70184643374 232330 W/HARDWARE C1318P and Hardware Type: S = Service Part, W = Wear Part, All Parts Are Sold As Individual (each) Unless Noted Otherwise...

  • Page 28: Engine Mount Group

    Engine Mount Group Front Of Machine Item UPC No Part No Description Type NOTES 00310007025 083371 GUARD BELT ASSY Includes: Belt Guard and Hardware BLADE SHAFT GUARD ASSMEBLY Includes: Blade Shaft Guard and 70184643375 232358 C1318 Hardware FRAME WELD MOTOR 00310007023 Includes: Engine Mount Only 083369...

  • Page 29: Main Frame Group

    Main Frame Group Front Of Machine Item UPC No Part No Description Type NOTES 70184643376 MAIN FRAME WELDMENT C318P Frame Only 232323 Includes Items: 3 (2x), 4 (2x), 5 (6x), 6 00310006550 AXLE REAR COMPLT W/WHEELS 082784 (2x), 7 (2x), and 11 00310005129 BUSH INNR MOT PIVOT (2) Sold In Set Of Two (2)

  • Page 30: Water Control Group

    Water Control Group Front Of Machine...
  • Page 31 Water Control Group Item UPC No Part No Description Type NOTES WATER TANK COMPLETE Includes: Water Tank and Stopper 00310351798 232356 C1318P/CS451 (Cap) STOPPER WATER TANK 00310006560 082794 C13/C13P18/C1318P Includes: Valve Assembly w/Hose Adapter (1), Male Quick Detach x 3/4" Garden Hose (1), Female Quick Detach (1) x ¾”...

  • Page 32: Front Pointer Group

    Front Pointer Group Front Of Machine Item UPC No Part No Description Type NOTES POINTER ASSY Includes: Front Pointer Rod, Pointer 00310024051 232127 C13PC18/C13P18/C1318P Frame, Wheel, and Hardware WHEEL POINTER W/HARDWARE 00310004622 Front Wheel and Hardware 232126 C13P18/C1318P POINTER ROD 00310004244 232125 Front Pointer Rod Only...
  • Page 33 Page Left Intentionally Blank...
  • Page 34 Saint-Gobain Abrasives 2770 West Washington Stephenville, TX 76401 Phone: 254-918-2310 Fax: 254-918-2312...

Table of Contents