Network Set Setting - Sanyo DSR-3000 Instruction Manual

NETWORK SET SETTING

NETWORK SET setting
1
Press the MENU button twice to display the MAIN MENU 2
screen.
The cursor moves to DISPLAY/VIDEO LOSS SET.
MENU
2
Use the jog dial to move the cursor to the NETWORK SET
setting, and then turn the shuttle dial clockwise.
The NETWORK SET sub-menu appears, and the cursor moves
to LAN CARD.
3
Turn the shuttle dial clockwise.
"LAN1" flashes.
Select LAN1 or LAN2 to suit the type of card being used.
•
LAN1: COREGA FEther PCC-TXD "CG-FEPCCTXD" type
(10/100 BASE-T) or COREGA FEther II PCC-TXD
"CG-FE2PCCTXD" type (10/100 BASE-T)
•
LAN2: COREGA Ether PCC-TD "CG-EPCCTD" type
(10 BASE-T) or COREGA Ether II PCC-TD
"CG-E2PCCTD" type (10 BASE-T) or COREGA Ether II
PCC-T (10 BASE-T) or D-Link DE-660
Note: Correct operation cannot be guaranteed if a LAN card other
than the one recommended above is used.
4
Use the jog dial to select the LAN card (example: " LAN1" ),
and then turn the shuttle dial clockwise.
The cursor moves to NETWORK CONTROL.
English
<NETWORK SET>
LAN CARD : LAN1
NETWORK CONTROL : OFF
IP ADDRESS : 192.168. 0. 1
SUBNET MASK : 255.255.255. 0
GATEWAY : 0. 0. 0. 0
PORT : 00080
ID : PASSWORD (4-8)
GUEST : 1111----
USER : 2222----
ADMIN : 3333----
<NETWORK SET>
LAN CARD : LAN1
NETWORK CONTROL : OFF
IP ADDRESS : 192.168. 0. 1
SUBNET MASK : 255.255.255. 0
GATEWAY : 0. 0. 0. 0
PORT : 00080
67
5
Turn the shuttle dial clockwise and use the jog dial to select
NETWORK CONTROL (example: " ON" ), and then turn the
shuttle dial clockwise to set (DISPLAY: ON).
The cursor moves to IP ADDRESS.
•
NETWORK CONTROL: ON (DISPLAY: ON) When DISPLAY
is set to ON, the characters "NETWORK CONTROL" are
displayed on the digital video recorder's monitor output all the
time during a network connection. In addition, when images
are being played back from the network, the digital video
recorder's monitor output also shows the playback images.
The digital video recorder cannot be operated during a network
connection. However, you can disconnect from the network by
pressing the EXIT/OSD button for 3 seconds.
•
NETWORK CONTROL: ON (DISPLAY: OFF) When DISPLAY
is set to OFF, the characters "NETWORK CONTROL" are not
displayed on the digital video recorder's monitor output during
a network connection. In addition, when images are being
played back from the network, the digital video recorder's
monitor output shows live images. The PLAY/STOP indicator
on the digital video recorder does not illuminate during
playback. (Recording is possible.) The digital video recorder
cannot be operated during a network connection. However,
you can disconnect from the network by pressing the
EXIT/OSD button for 3 seconds.
•
OFF: Network operations are disabled.
Note:
•
Control through the network is not possible unless NETWORK
CONTROL is ON.
When you are connected to a network, it should be switched OFF if
control from the network is not required.
•
If DIGITAL SERIES RECORDING in the RECORDING
CONDITIONS SET menu is set to "ON", NETWORK CONTROL
cannot be set to "ON".
•
The main unit cannot be operated while network operations are in
progress. However, the digital video recorder can be disconnected
from the network by pressing the EXIT/OSD button for
approximately 3 seconds.
6
Turn the shuttle dial clockwise and use the jog dial and
shuttle dial to display the IP ADDRESS (example:
" 192.168.0.1" ), and then turn the shuttle dial clockwise.
With the final shuttle dial movement, the cursor moves to
SUBNET MASK.
7
Turn the shuttle dial clockwise and use the jog dial and
shuttle dial to display the SUBNET MASK (example:
" 255.255.255.0" ), and then turn the shuttle dial clockwise.
With the final shuttle dial movement, the cursor moves to
GATEWAY.
<NETWORK SET>
LAN CARD : LAN1
NETWORK CONTROL : ON (DISPLAY:ON)
IP ADDRESS : 192.168. 0. 1
SUBNET MASK : 255.255.255. 0
GATEWAY : 0. 0. 0. 0
PORT : 00080
<NETWORK SET>
LAN CARD : LAN1
NETWORK CONTROL : ON (DISPLAY:ON)
IP ADDRESS : 192.168. 0. 1
SUBNET MASK : 255.255.255. 0
GATEWAY : 0. 0. 0. 0
PORT : 00080
<NETWORK SET>
LAN CARD : LAN1
NETWORK CONTROL : ON (DISPLAY:ON)
IP ADDRESS : 192.168. 0. 1
SUBNET MASK : 255.255.255. 0
GATEWAY : 0. 0. 0. 0
PORT : 00080