Sequential Play; Audio Recording; Rear Terminal Settings - Mitsubishi Electric DX-TL910U Installation And Operation Manual

<INITIAL SET UP/INFORMATION> (continued)
o SEQUENTIAL PLAY
It is possible to make archive of the video recorded with
this unit to an analogue video recorder, etc., while playing
back the video of each camera in order using the single
screen display. During single screen sequential playback,
the SPLIT/SEQUENCE button will light. In addition, the
playback order/time of each camera will be the order of
the recorded video.
<HDD SETTINGS>
HDD REPEAT REC MAIN
HDD REPEAT REC SUB
HDD REPEAT PLAY
IM-CHECK PLAY
>> SEQUENTIAL PLAY
Setting ( default : "OFF" )
"ON" : Plays back the video in the single screen se-
quential mode.
"OFF" : Does not play back the video in the single
screen sequential mode.
Playback is performed during camera sequential play
at an interval of 30P. To change the playback interval, press
the PLAY button (or the REV. PLAY button)(
"Changing playback intervals, pages 69,70).
1. Press the SET UP button } <SETTINGS> } <INITIAL SET
UP/INFORMATION> } Select "SEQUENTIAL PLAY" in the
<HDD SETTINGS> screen. Display the desired setting and
confirm.
2. Turn the SHUTTLE ring counterclockwise or press the SET
UP button.
3. Press the PLAY button.
4. Press one of the camera number buttons with recorded video.
• Single screen sequential playback starts.
When performing camera sequential playback for
video with long recording intervals, the video of the
largest camera number selected for recording will be
played back the longest.
Only the camera number (title) of the pressed cam-
era number button is displayed. Other camera number
(titles) will not be displayed. If display is not necessary,
select "NONE" in the <CAMERA DISPLAY> (
page 36).
I AUDIO RECORDING
This unit can simultaneously record audio along with the
video. When recording audio, the continuous recording
time becomes shorter than when recording only video.
<INITIAL SET UP/INFORMATION>
HDD SETTINGS
>>AUDIO RECORDING

REAR TERMINAL SETTINGS

COMMUNICATION PORT SETTINGS
INFORMATION/SERVICE
PASSWORD
LANGUAGE SELECTION
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
52
Setting ( default : "OFF" )
"ON" : Records video and audio.
"ALARM" : During alarm recording or emergency re-
cording, records video and audio.
"OFF" : Does not record audio.
1. Press the SET UP button } <SETTINGS> } Select "AUDIO
RECORDING" in the <INITIAL SET UP/INFORMATION>
screen. Display the desired setting and confirm.
ON
2. Turn the SHUTTLE ring counterclockwise or press the SET
OFF
OFF
UP button.
OFF
OFF When setting "AUDIO RECORDING" to "ON", a
speaker display (
time display in the <RECORD SETTING> and
<RECORD SETTING A> ~ <RECORD SETTING D>
screens.
see
Even when setting "AUDIO RECORDING" to "ON",
audio cannot be recorded for the following settings.
• Audio recording cannot be performed when "PPS" of
"RECORD SETTING" are all set to smaller than
"0.333P" when setting normal recording. In this case,
( X ) appears to the right of recordable time display.
• When the camera selection during alarm recording is
as follows :
"ALARM CH" : "A-PPS" of all cameras set for alarm
recording are set to smaller than "0.333P".
"ALARM PLUS" : "PPS" and "A-PPS" of all cameras
set for normal recording and alarm recording are set to
smaller than "0.333P".
see
OFF
) appears to the right of recordable
<RECORD SETTING>
<RECORD SETTING> >>ALARM CH
NO PPS GRADE A-PPS
1 3P STD 3P
2
3P STD 3P
3
3P STD 3P
4
3P STD 3P
5
3P STD 3P
6
3P STD 3P
7 3P STD 3P
8
3P STD 3P
9
3P STD 3P
<ESTD REC> D H
A-GRADE
STD
STD
STD
STD
STD
STD
STD
STD
STD
M