Konica Minolta BIZHUB 750 User Manual
  1. Manuals
  2. Brands
  3. Konica Minolta Manuals
  4. All in One Printer
  5. bizhub 750
  6. User manual

Konica Minolta BIZHUB 750 User Manual

Hide thumbs Also See for BIZHUB 750:
1
2
Table Of Contents
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual, Function Manual
750/600
User Manual

Advertisement

Table of Contents
loading

Related Manuals for Konica Minolta BIZHUB 750

Summary of Contents for Konica Minolta BIZHUB 750

  • Page 1 750/600 User Manual...

  • Page 3: Table Of Contents

    Checking the copy settings ............1-16 Enlarging the size of text in touch panel screens ......1-16 Displaying explanations of functions and settings....... 1-16 Interrupting a copy job ..............1-16 Printing a sample copy ..............1-16 bizhub 750/600 (Phase 2) Contents-1...
  • Page 4 USER INSTRUCTIONS FCC PART 15 - RADIO FREQUENCY DEVICES (for U.S.A. users) ......2-12 INTERFERENCE-CAUSING EQUIPMENT STANDARD (ICES-003 ISSUE 4) (for Canada users) ........2-12 For users in countries not subject to class B regulations..... 2-13 Contents-2 bizhub 750/600 (Phase 2)
  • Page 5 Automatically conserving energy (Sleep Mode)......3-33 Manually conserving energy ............3-34 Limiting machine usage according to a schedule (Weekly Timer) 3-35 Controlling the use of this machine with user authentication ..3-37 Using the machine with account track......... 3-41 bizhub 750/600 (Phase 2) Contents-3...
  • Page 6 To specify a margin setting............4-30 To change scan settings for each document ....... 4-32 Selecting a paper setting..............4-36 Automatically selecting the paper size ("Auto Paper Select" setting) ............4-37 Manually selecting the desired paper size........4-38 Contents-4 bizhub 750/600 (Phase 2)
  • Page 7 Using finisher manually..............4-95 To use finisher manually .............. 4-97 4.14 Scanning the next original to be copied while a copy job is being printed (Next Job Reservation) ........4-99 To reserve a copy job ..............4-99 bizhub 750/600 (Phase 2) Contents-5...
  • Page 8 To set the "Sound Volume Setting" function ........ 5-40 To set the "Touch Panel Adj." function......... 5-43 To set the "Auto Reset Notification" function....... 5-45 To set the "Enlarge Display Confirmation Screen" function ..5-48 Contents-6 bizhub 750/600 (Phase 2)
  • Page 9 Main body ..................6-14 ADF ....................6-17 Finisher..................6-17 Main messages and their remedies..........6-18 Specifications bizhub 750/600 ................7-3 ADF ....................7-5 Option specifications ..............7-6 Large Capacity Unit LU-401 ............7-6 Large Capacity Unit LU-402 ............7-6 Finisher FS-504................7-7 Finisher FS-505................
  • Page 10 Inserting copies of a different original at a specified location ("Insert Image" function)..............9-7 To copy using the "Insert Image" function ........9-8 Adding cover pages ("Cover Mode" function) ......9-12 To copy using the "Cover Mode" function ........9-13 Contents-8 bizhub 750/600 (Phase 2)
  • Page 11 Erasing specified areas of copies ("Erase" functions)....9-81 To erase specified areas of copies ("Erase" function) ....9-82 To erase the center of copies ("Center Erase" function)....9-85 To erase specified areas of copies ("Non-Image Area Erase" function) ..........9-88 bizhub 750/600 (Phase 2) Contents-9...
  • Page 12 Control panel ................11-4 ADF platen guide cover ..............11-5 Paper take-up roller ..............11-5 11.2 Viewing counters (Meter count) ............. 11-6 To view the counters..............11-6 11.3 When the message "Preventive maintenance time." appears ..11-8 Contents-10 bizhub 750/600 (Phase 2)
  • Page 13 Administrator/Machine setting ........... 13-49 One-touch registration ............... 13-49 User authentication/Account track ..........13-50 Network setting................13-53 Copier setting................13-53 Printer setting................13-55 System connection ..............13-55 Security setting ................13-56 Displaying the administrator setting screen....... 13-60 bizhub 750/600 (Phase 2) Contents-11...
  • Page 14 Account track setting..............13-113 Account track registration............13-113 Account track counter .............. 13-117 To check the counter ..............13-118 13.10 Password rules ................13-120 Conditions of the password rules ..........13-120 13.11 Enhanced security settings ............13-122 Contents-12 bizhub 750/600 (Phase 2)
  • Page 15 14 Appendix 14.1 Entering text..................14-3 To type text .................. 14-5 List of available characters ............14-5 14.2 Function combination table ............14-6 15 Index bizhub 750/600 (Phase 2) Contents-13...

  • Page 16: Bizhub 750/600 (Phase 2)

    Contents-14 bizhub 750/600 (Phase 2)

  • Page 17: Introduction

    Introduction...
  • Page 19 The illustrations used in this manual may appear slightly different from views of the actual equipment. bizhub 750/600 (Phase 2)

  • Page 20: Energy Star

    "low-power mode" after a period of inactivity. An ® ENERGY STAR product uses energy more efficiently, saves you money on utility bills and helps protect the environment. bizhub 750/600 (Phase 2)

  • Page 21: Trademarks And Registered Trademarks

    Introduction Trademarks and registered trademarks KONICA MINOLTA, KONICA MINOLTA Logo, and The essentials of imaging are registered trademarks or trademarks of KONICA MINOLTA HOLDINGS, INC. PageScope and bizhub are registered trademarks or trademarks of KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. Netscape Communications, the Netscape Communications logo, Netscape Navigator, Netscape Communicator, and Netscape are trademarks of Netscape Communications Corporation.

  • Page 22: Available Features

    Scan" setting)" on page 4-13. Copying an original containing various page sizes An original with various page sizes can be scanned and copied together. For details, refer to "Copying original of mixed sizes ("Mixed Original" setting)" on page 4-18. bizhub 750/600 (Phase 2)

  • Page 23: Specifying Separate Horizontal And Vertical Zoom Ratios

    Copying multiple original pages onto a single page Multiple pages of the original can be printed together on a single page. For details, refer to "Copying multiple original pages onto a single page (Combine Originals)" on page 4-66. bizhub 750/600 (Phase 2)

  • Page 24: Sorting Copies

    For details, refer to "Separating copies by sets ("Sort" setting)" on page 4-71, "Separating copies by pages ("Group" setting)" on page 4-73. Stapling copies Copies can be stapled together before they are fed out. For details, refer to "Stapling copies (Staple settings)" on page 4-76. bizhub 750/600 (Phase 2)

  • Page 25: Punching Holes In Copies

    Zigzag folding and folding in three Copies can be folded fanned or in three. For details, refer to "To fold copies fanned ("Z-Fold")" on page 4-91 and "To fold copies in three ("Tri-Fold")" on page 4-93. bizhub 750/600 (Phase 2)

  • Page 26: Inserting Paper Between Copies Of Overhead Projector Transparencies

    For details, refer to "Inserting copies of a different original at a specified location ("Insert Image" function)" on page 9-7. 1-10 bizhub 750/600 (Phase 2)

  • Page 27: Adding A Cover Page/Insertion

    Double-sided copies can be made so that the chapter title pages are printed on the front sides of pages. For details, refer to "Specifying pages to be printed on the front side ("Chapters" function)" on page 9-24. bizhub 750/600 (Phase 2) 1-11...

  • Page 28: Copying With Reversed Colors

    Repeating copy images An original image can be repeatedly printed on a single sheet of paper. For details, refer to "Repeating the copy image on a sheet of paper ("Image Repeat" function)" on page 9-47. 1-12 bizhub 750/600 (Phase 2)

  • Page 29: Splitting An Original Page Into Two Copies

    Making copies for filing Copies can be printed with a filing margin so they can easily be stored in filing binders. For details, refer to "Adding filing margins to copies ("Page Margin" function)" on page 9-64. bizhub 750/600 (Phase 2) 1-13...

  • Page 30: Adjusting The Image To Fit The Paper Size

    Adjustment settings)" on page 9-72. Copying with a layout for center binding Copies can be made with the pages arranged in the layout of a magazine. For details, refer to "Copying booklet original ("Booklet" function)" on page 9-78. 1-14 bizhub 750/600 (Phase 2)

  • Page 31: Erasing Sections Of Copies

    For details, refer to "Managing jobs (Job list)" on page 12-3. Programming copy settings Frequently used copy settings can be programmed and recalled to be used with other copy jobs. For details, refer to "Registering copy programs (Mode Memory)" on page 5-13. bizhub 750/600 (Phase 2) 1-15...

  • Page 32: Checking The Copy Settings

    The text and buttons in the touch panel can be displayed in a larger size that is easier to read, allowing basic operations to be easily performed. For details, refer to the Enlarge Display Operations of the bizhub 750/600 User manual.

  • Page 33: Explanation Of Manual Conventions

    Text formatted in this style provides additional assistance. % Text formatted in this style describes the action that will ensure the desired results are achieved. bizhub 750/600 (Phase 2) 1-17...

  • Page 34: Tips

    Text highlighted in this manner contains references for more detailed information. Special text markings [Stop] key The names of keys on the control panel are written as shown above. MACHINE SETTING Display texts are written as shown above. 1-18 bizhub 750/600 (Phase 2)

  • Page 35: Descriptions And Symbols For Original And Paper

    (X), the paper has a vertical or portrait orientation, indicated by w. Crosswise (v) If the width (Y) of the paper is longer than the length (X), the paper has a horizontal or landscape orientation, indicated by v. bizhub 750/600 (Phase 2) 1-19...

  • Page 36: User Manuals

    This manual describes the operation of the FAX functions which can be used when the optional fax kit, FK-502, is installed. - Refer to this user manual for details on the operation of the FAX functions. 1-20 bizhub 750/600 (Phase 2)

  • Page 37: Ic-202 User Manual

    This manual contains details on operating procedures using the optional Image Controller (IC-202). - Refer to the user manual (PDF data) provided in the User Software CD- ROM attached to IC-202 for the procedures to use the printer functions. bizhub 750/600 (Phase 2) 1-21...

  • Page 38: Legal Restrictions On Copying

    When in doubt about the nature of a document, consult with legal counsel. 1-22 bizhub 750/600 (Phase 2)

  • Page 39: Installation And Operation Precautions

    Installation and operation precautions...

  • Page 41: Safety Information

    7 WARNING Ignoring this warnings could cause serious injury or even death. Do not ignore this safety advices. 7 CAUTION Ignoring this cautions could cause injury or damage to property. Do not ignore this safety advices. bizhub 750/600 (Phase 2)

  • Page 42: Meaning Of Symbols

    • Do not modify this product, as a fire, electrical shock, or breakdown could result. If the product employs a laser, the laser beam source could cause blindness. bizhub 750/600 (Phase 2)

  • Page 43: Power Cord

    Should any of these conditions be found, immediately turn OFF the power switch, unplug the power cord from the pow- er outlet, and then call your authorized service representa- tive. bizhub 750/600 (Phase 2)

  • Page 44: Power Source

    Ignoring this cautions could cause injury or damage to property. Do not ignore this safety advices. Caution Symbol • The outlet must be near the equipment and easily accessible. Otherwise you can not pull out the power plug when an emer- gency occurs. bizhub 750/600 (Phase 2)

  • Page 45: Power Plug

    7 WARNING Ignoring this warnings could cause serious injury or even death. Do not ignore this safety advices. Warning Symbol • Connect the power cord to an electrical outlet that is equipped with a grounding terminal. bizhub 750/600 (Phase 2)

  • Page 46: Installation

    • Do not let any object plug the ventilation holes of this prod- uct. Heat could accumulate inside the product, resulting in a fire or malfunction. • Do not use flammable sprays, liquids, or gases near this product, as a fire could result. bizhub 750/600 (Phase 2)

  • Page 47: Ventilation

    If you keep on using it as is, a fire or electrical shock could result. 7 CAUTION Ignoring this cautions could cause injury or damage to property. Do not ignore this safety advices. bizhub 750/600 (Phase 2)

  • Page 48: Consumables

    Licking or ingesting any of these things could injure your health. • Do not store toner units and PC drum units near a floppy disk or watch that are susceptible to magnetism. They could cause these products to malfunction. 2-10 bizhub 750/600 (Phase 2)

  • Page 49: When Moving The Machine

    7 CAUTION Ignoring this cautions could cause injury or damage to property. Do not ignore this safety advices. Caution Symbol • Unplug the product when you will not use the product for long periods of time. bizhub 750/600 (Phase 2) 2-11...

  • Page 50: Regulation Notices

    FCC rules. INTERFERENCE-CAUSING EQUIPMENT STANDARD (ICES-003 ISSUE 4) (for Canada users) This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. 2-12 bizhub 750/600 (Phase 2)

  • Page 51: For Users In Countries Not Subject To Class B Regulations

    Usynlig laserstråling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for stråling. Klasse 1 laser produkt der op- fylder IEC60825 sikkerheds kravene. Dette er en halvlederlaser. Laserdiodens højeste styrke er 15 mW og bølgelængden er 770-800 nm. bizhub 750/600 (Phase 2) 2-13...

  • Page 52: For Norway Users

    Om apparaten används på annat sätt än i denna bruksanvisning spe- cificerats, kan användaren utsättas för osynlig laserstrålning, som överskrider gränsen för laserklass 1. Det här är en halvledarlaser. Den maximala effekten för laserdioden är 15 mW och våglängden är 770-800 nm. 2-14 bizhub 750/600 (Phase 2)

  • Page 53: Acoustic Noise (For European Users Only)

    Osynlig laserstrålning när denna del är öppnad och spärren är urkopp- lad. Betrakta ej strålen. Rear side of main body Acoustic noise (for European users only) Maschinenlärminformations-Verordnung 3. GPSGV: Der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemäss EN ISO 7779. bizhub 750/600 (Phase 2) 2-15...

  • Page 54: For Eu Member States Only

    Recycling of this product will help to conserve natural resources and prevent potential negative consequences for the environment and human health caused by inappropriate waste handling. 2-16 bizhub 750/600 (Phase 2)

  • Page 55: Caution Notations And Labels

    Caution notations and labels Safety precaution notations and labels appear on this machine at the following positions. Be very careful that an accident does not occur when operations such as removing paper misfeeds are performed. bizhub 750/600 (Phase 2) 2-17...
  • Page 56 Be sure to hold both sides of the printed sheets when removing them, and DO NOT leave your hand on the printed sheets while the primaty (main) tray goes up. 2-18 bizhub 750/600 (Phase 2)

  • Page 57: Space Requirements

    To ensure that machine operation, consumables replenishing, part replacement, and regular maintenance can easily be performed, adhere to the recommended space requirements detailed below. Unit: mm (inch) bizhub 750/600 Unit: mm (inch) bizhub 750/600 + LU-402 bizhub 750/600 (Phase 2) 2-19...
  • Page 58 Installation and operation precautions Unit: mm (inch) bizhub 750/600 + FS-602 + PI-501 + ZU-602 Unit: mm (inch) bizhub 750/600 + FS-602 + PI-501 + LU-402 Reminder Be sure to allow a clearance of 200 mm (7-3/4 in.) or more at the back of this machine for the ventilation duct.

  • Page 59: Operation Precautions

    - Copies that are to be kept for a long time should be kept where they are not exposed to light in order to prevent them from fading. - Adhesive that contains solvent (e.g., spray glue) may dissolve the toner on copies. bizhub 750/600 (Phase 2) 2-21...
  • Page 60 Installation and operation precautions 2-22 bizhub 750/600 (Phase 2)

  • Page 61: Before Making Copies

    Before making copies...

  • Page 63: Part Names And Their Functions

    Before making copies Before making copies Part names and their functions Outside of machine bizhub 750/600 (Phase 2)
  • Page 64 Front doors (left and right) Opened when clearing paper misfeeds Exit tray Collects printed pages Note The maximum angle that the ADF is opened can be adjusted in two stages. For details, contact your technical representative. bizhub 750/600 (Phase 2)
  • Page 65 Supplies power to the machine Serial port (RS-232C) Used for transmissions with CS Remote Care Network connector (10Base- Used for connecting the network cable when this T/100Base-TX) machine is used for network printing and network scanning bizhub 750/600 (Phase 2)

  • Page 66: Inside Of Machine

    Forms the copy image Fusing unit Fuses the image that was formed onto the paper Main power switch Used to turn the machine on and off Total counter Shows the total number of pages that have been printed bizhub 750/600 (Phase 2)
  • Page 67 Before making copies Reminder Parts in the fusing unit are extremely hot. Touching any part in this unit may result in burns. bizhub 750/600 (Phase 2)

  • Page 68: Options

    Before making copies Options bizhub 750/600 (Phase 2)
  • Page 69 Fax kit FK-502 Allows this machine to be used as a fax machine Security Kit SC-501 Installed to encode the data saved on the hard disk so that the hard disk can be used more safely. bizhub 750/600 (Phase 2)

  • Page 70: Large Capacity Unit Lu-401/Lu-402

    Pressed to lower the bottom plate in the tray to load paper Bottom plate Raised as the paper is used. Lower by pressing the bottom-plate-lowering button. Trailing-edge guide Positions the trailing edge of the paper to be load- 3-10 bizhub 750/600 (Phase 2)

  • Page 71: Finisher Fs-504/Fs-505/Fs-602 (+ Punch Kit Pk-504/Pk-505)

    PK- 504/PK-505 is installed BM tray Collects pages printed with the "Half Fold", "Fold & Staple", or "Tri-Fold" settings or with the "Cover Mode" function Main tray Collects printed pages Sub tray Collects printed pages bizhub 750/600 (Phase 2) 3-11...
  • Page 72 Before making copies Finisher FS-602 Finisher FS-504 +Punch Kit PK-504/PK-505 Finisher FS-505 +Punch Kit PK-504/PK-505 3-12 bizhub 750/600 (Phase 2)
  • Page 73 10-15.) Stacker unit handle Used to pull out the unit when clearing paper mis- feeds in the stacker unit and when refilling the sta- ples Staple cartridge Removed when refilling the staples (See p. 10-8) bizhub 750/600 (Phase 2) 3-13...

  • Page 74: Post Inserter Pi-501

    Slide to fit the size of paper being loaded when loading with cover sheets. Upper tray Load with cover sheets. Lower tray Load with cover sheets. Lower tray paper guide Slide to fit the size of paper being loaded when loading with cover sheets. 3-14 bizhub 750/600 (Phase 2)

  • Page 75: Z Folding Unit Zu-601/Zu-602

    Used to pull out the unit when clearing paper mis- feeds paper misfeeds Opened when clearing paper misfeeds Punch dust box Removed when emptying punch dust that has ac- cumulated from using the Punch settings (See p. 10-18.) bizhub 750/600 (Phase 2) 3-15...

  • Page 76: Shift Tray Sf-601

    Before making copies Shift Tray SF-601 Part name Description Exit tray Collects printed pages Upper cover Opened when clearing paper misfeeds 3-16 bizhub 750/600 (Phase 2)

  • Page 77: Control Panel

    Press to enter Fax mode. While the machine is in Fax mode, the indicator on the [Fax] key lights up in green. For details, refer to the bizhub 750/600 User manu- al [Facsimile Operations]. [Scan] key Press to enter Scan mode.
  • Page 78 Press to display the screen for specifying user ac- cessibility functions. [Help] key Press to display the Main Help Menu screen, where descriptions of the various functions and details of operations can be displayed. (See p. 5-20.) 3-18 bizhub 750/600 (Phase 2)
  • Page 79 Do not apply extreme pressure to the touch panel, otherwise it may be scratched or damaged. Never push down on the touch panel with force, and never use a hard or pointed object to make a selection in the touch panel. bizhub 750/600 (Phase 2) 3-19...

  • Page 80: Basic Settings Screen (Basic Screen)

    When the machine is ready to begin making copies after being turned on, the Basic screen appears. To activate a function or to select a setting, lightly touch the desired button in the touch panel. TYPE1 TYPE2 3-20 bizhub 750/600 (Phase 2)
  • Page 81 Various commands are available to specify the box where the data is to be saved and whether or not the data is printed when it is saved. For details, re- fer to the Box Operations of the bizhub 750/600 User manual. [Separate Scan] key Touch to scan the original in separate batches.

  • Page 82: Icons That Appear In The Touch Panel

    Indicates that 25% to 50% of the paper remains in the paper tray Indicates that less than 25% of the paper remains in the paper tray Indicates that no paper remains in the paper tray 3-22 bizhub 750/600 (Phase 2)
  • Page 83 Before making copies Icon Description Indicates that the toner cartridge must be replaced Indicates the orientation in which the original is positioned Indicates that "Enhanced Security Mode" is set to "ON" bizhub 750/600 (Phase 2) 3-23...

  • Page 84: Adjusting The Angle Of The Control Panel

    Before making copies Adjusting the angle of the control panel The control panel can be adjusted to either of two angles. Adjust the control panel to the angle that allows for easy operation. 3-24 bizhub 750/600 (Phase 2)

  • Page 85: To Adjust The Angle Of The Control Panel

    To return the control panel to the upper position, press the control panel release lever, and then pull up on the control panel. Note The control panel can also be grabbed anywhere on its outer edge and lifted. bizhub 750/600 (Phase 2) 3-25...

  • Page 86: Turning On The Main Power And The Sub Power

    The main power switch is on the left side inside the machine. Turn on the main power switch. The indicator on the main power switch lights up in green. Turn on the sub power switch. 3-26 bizhub 750/600 (Phase 2)
  • Page 87 Note A job can also be queued while the machine is warming up after the sub power switch is turned on. For details, refer to "To scan during warm-up" on page 3-28. bizhub 750/600 (Phase 2) 3-27...

  • Page 88: To Scan During Warm-Up

    The indicator on the [Start] key lights up in green. Position the original to be copied. How is the original positioned? % For details on positioning the original to be copied, refer to "Positioning the original" on page 4-9. 3-28 bizhub 750/600 (Phase 2)
  • Page 89 After the machine has finished warming up, the scanned image will be printed. The machine takes about 5 minutes (bizhub 750)/4 minutes 30 seconds (bizhub 600) to warm up at normal room temperature (20°C) when the control panel is turned on using the sub power switch after the machine is turned on using the main power switch.

  • Page 90: To Turn Off The Machine

    Do not turn off the machine with the main power switch while a queued job or stored data is waiting to be printed, otherwise the jobs will be deleted. 3-30 bizhub 750/600 (Phase 2)

  • Page 91: Automatically Canceling The Settings (Automatic Panel Reset)

    The length of time until the automatic panel reset operation is performed and whether or not it is performed can be set from the Administrator mode. For details, refer to "System setting" on page 13-26. bizhub 750/600 (Phase 2) 3-31...

  • Page 92: Automatically Canceling The Mode Screen (Automatic System Reset)

    Sleep mode instead. For details, refer to "System setting" on page 13-39. The Low Power mode can also be canceled by pressing any key in the control panel or by touching the touch panel. 3-32 bizhub 750/600 (Phase 2)

  • Page 93: Automatically Conserving Energy (Sleep Mode)

    Low Power mode if no operation is performed for 15 minutes, and then the machine enters Sleep mode after 90 minutes have elapsed. The length of time until the machine enters Sleep mode can be changed. For details, refer to "System setting" on page 13-39. bizhub 750/600 (Phase 2) 3-33...

  • Page 94: Manually Conserving Energy

    Detail Whether the machine enters Low Power mode or Sleep mode when the [Power Save] key is pressed can be set from the Administrator mode. For details, refer to "System setting" on page 13-39. 3-34 bizhub 750/600 (Phase 2)

  • Page 95: Limiting Machine Usage According To A Schedule (Weekly Timer)

    Type in the password (up to 8 digits) for non-business hours. How is the password for non-business hours specified? % For details on specifying the password for non-business hours, refer to "System setting" on page 13-39. Touch [OK]. bizhub 750/600 (Phase 2) 3-35...
  • Page 96 From Administrator mode, the machine can be set so that the screen for entering the password for non-business hours is not displayed. The default setting for the "Password for Non-Business Hours" parameter is "OFF" (the screen is not displayed). 3-36 bizhub 750/600 (Phase 2)

  • Page 97: Controlling The Use Of This Machine With User Authentication

    0 If a user enters an incorrect password the specified number of times, that user may be locked out and no longer be able to use the machine. Contact the administrator to cancel operation restrictions. Touch [User Name]. bizhub 750/600 (Phase 2) 3-37...
  • Page 98 Before making copies Type in the user name, and then touch [OK]. Touch [Password]. Type in the password, and then touch [OK]. 3-38 bizhub 750/600 (Phase 2)
  • Page 99 When you finish printing, press the [Access] key. A message appears, requesting confirmation to log off. Touch [Yes]. Authentication screen appears again. Detail For details on specifying user authentication settings, refer to "User authentication/Account track" on page 13-50. bizhub 750/600 (Phase 2) 3-39...
  • Page 100 If [Public User Access] appears, users with no access to a user name and password can touch [Public User Access] to use this machine. Note If account track settings have been applied, a screen for entering account information appears. 3-40 bizhub 750/600 (Phase 2)

  • Page 101: Using The Machine With Account Track

    0 A total of 1000 users and accounts can be registered when the hard disk drive is installed. Touch [Account Name]. – If the Administrator mode settings have been set to "Password Only", touch [Input], and then continue with step 4. bizhub 750/600 (Phase 2) 3-41...
  • Page 102 Before making copies Type in the account name, and then touch [OK]. Touch [Password]. Type in the password, and then touch [OK]. 3-42 bizhub 750/600 (Phase 2)
  • Page 103 When you are finished printing, press the [Access] key. A message appears, requesting confirmation to log off. Touch [Yes]. Authentication screen appears again. Detail For details on specifying account track settings, refer to "User authentication/Account track" on page 13-50. bizhub 750/600 (Phase 2) 3-43...

  • Page 104: To Load Paper (Tray 1 Or 2)

    Reminder Do not load so much paper that the top of the stack is higher than the , mark. Make sure that the trailing-edge guide is adjusted to fit the size of the loaded paper. 3-44 bizhub 750/600 (Phase 2)
  • Page 105 If there is space between the trailing-edge guide and the paper, the paper will not be fed correctly. Do not close the paper tray with too much force, otherwise the weight of the tray and paper will apply an impact to the machine that may cause damage. bizhub 750/600 (Phase 2) 3-45...

  • Page 106: Loading Paper Into The Tray 3 Or 4

    Slide the lateral guide to fit the size of paper being loaded. – Move the lateral guide while holding the release button pressed. When the button is released, the guide is locked in place. Fully push in the paper tray. 3-46 bizhub 750/600 (Phase 2)
  • Page 107 Reminder Do not close the paper tray with too much force, otherwise the weight of the tray and paper will apply an impact to the machine that may cause damage. bizhub 750/600 (Phase 2) 3-47...

  • Page 108: Loading Paper Into The Bypass Tray

    Open the bypass tray to the right, and then open the folded tray to the right. Insert the paper as much as possible into the feed slot. Slide the lateral guides to fit the size of paper being loaded. 3-48 bizhub 750/600 (Phase 2)
  • Page 109 When loading overhead projector transparencies, load them in the v orientation, as shown in the illustration. Do not load overhead projector transparencies in the w orientation. Load overhead projector transparencies one sheet at a time. bizhub 750/600 (Phase 2) 3-49...
  • Page 110 Be sure to load letterhead paper so that the side to be printed on faces Note The image will be printed on the surface of the paper facing down when the paper is loaded into the bypass tray. 3-50 bizhub 750/600 (Phase 2)

  • Page 111: Loading Paper Into The Lcu (Lu-401/Lu-402)

    To load paper (LCU) Open the upper door of the large capacity unit. Press the bottom-plate-lowering button. (LU-401) – The bottom plate is lowered. (LU-402) bizhub 750/600 (Phase 2) 3-51...
  • Page 112 Before making copies Load the paper into the tray. (LU-401) (LU-402) 3-52 bizhub 750/600 (Phase 2)
  • Page 113 Make sure that the trailing-edge guide is adjusted to fit the size of the loaded paper. If there is space between the trailing-edge guide and the paper, the paper will not be fed correctly. bizhub 750/600 (Phase 2) 3-53...

  • Page 114: Loading Paper Of A Different Size Into Paper Trays

    Remove the trailing-edge guide, and then insert it at the position for the desired paper size. – Press the button to remove the trailing-edge guide. – Insert the trailing-edge guide into the hole corresponding to the size indicated on the bottom plate. 3-54 bizhub 750/600 (Phase 2)
  • Page 115 Do not close the paper tray with too much force, otherwise the weight of the tray and paper will apply an impact to the machine that may cause damage. bizhub 750/600 (Phase 2) 3-55...

  • Page 116: When Thick Paper Is Loaded Into A Paper Tray

    Open the front doors (left and right). Turn lever M4 to the left, and then pull out the ADU unit. Lever M4 Set the conveyance lever to "5.5 × 8.5 A5 Thick paper". Conveyance lever 3-56 bizhub 750/600 (Phase 2)
  • Page 117 Before making copies Return the ADU unit to its original position. Close the front doors (left and right). Note After using thick paper, be sure to reset the conveyance lever to "NORMAL". bizhub 750/600 (Phase 2) 3-57...
  • Page 118 Before making copies 3-58 bizhub 750/600 (Phase 2)

  • Page 119: Basic Copy Operations

    Basic copy operations...

  • Page 121: General Copy Operation

    To make a copy Press the [Copy] key to display the Basic screen in Copy mode. Position the original to be copied. – For details on positioning the original, refer to "Positioning the original" on page 4-9. bizhub 750/600 (Phase 2)
  • Page 122 4-68. – For details on specifying the "Folding" function, refer to "Specifying folding settings" on page 4-85. – For details on specifying settings for the Application functions, refer to "Application functions" on page 9-3. bizhub 750/600 (Phase 2)
  • Page 123 The next copy operation can be queued while a copy operation is being performed. For details, refer to "Scanning the next original to be copied while a copy job is being printed (Next Job Reservation)" on page 4-99. bizhub 750/600 (Phase 2)

  • Page 124: Operations That Cannot Be Combined

    Operations where the setting specified last is given priority As an example, the procedure for setting the "Booklet" function after selecting the "2 Position" Staple setting is described below. Select the " 2 Position" Staple setting. bizhub 750/600 (Phase 2)
  • Page 125 Set the "Booklet" function. The "2 Position" Staple setting is automatically cancelled, and the "Booklet" function is set. To select the "2 Position" Staple setting, cancel the "Booklet" function, and then select the "2 Position" setting. bizhub 750/600 (Phase 2)

  • Page 126: Operations Where The Setting Specified First Is Given Priority

    "2 Position" Staple setting cannot be selected. The "Booklet" function remains selected and the "2 Position" Staple setting is canceled. To select the "2 Position" Staple setting, cancel the "Booklet" function, and then select the "2 Position" setting. bizhub 750/600 (Phase 2)

  • Page 127: Positioning The Original

    Position the original face up in the ADF. – Position the original pages so that the top of the original is toward the back or the right side of the machine. bizhub 750/600 (Phase 2)
  • Page 128 For details on selecting the original orientation, refer to "Selecting the original orientation (Original Direction settings)" on page 4-24. – For details on selecting the position of the binding margin, refer to "Selecting the position of the binding margin (Margin settings)" on page 4-28. 4-10 bizhub 750/600 (Phase 2)

  • Page 129: To Position The Original On The Original Glass

    "Selecting the original orientation (Original Direction settings)" on Measuring guides page 4-24. – For details on selecting the position of the binding margin, refer "Selecting the position of the binding margin (Margin settings)" on page 4-28. bizhub 750/600 (Phase 2) 4-11...
  • Page 130 Close the ADF. 4-12 bizhub 750/600 (Phase 2)

  • Page 131: Scanning The Original In Separate Batches ("Separate Scan" Setting)

    Up to 100 sheets can be loaded at one time. In the Basic screen, touch [Separate Scan]. – To cancel the "Separate Scan" setting, touch [Separate Scan] again to deselect it. bizhub 750/600 (Phase 2) 4-13...
  • Page 132 For details, refer to "Stopping scanning/printing" on page 4-101. After the original is scanned, the message "Set the next original and press [Start]." appears. After all original pages have been scanned, touch [Finish]. Press the [Start] key. 4-14 bizhub 750/600 (Phase 2)

  • Page 133: Scanning A Multi-Page Original From The Original Glass

    For details on positioning the original, refer to "To position the original on the original glass" on page 4-11. When loaded in the When loaded in the v orientation: w orientation: Close the ADF. In the Basic screen, touch [Simplex/Duplex]. The Simplex/Duplex screen appears. bizhub 750/600 (Phase 2) 4-15...
  • Page 134 [Start]." appears. Position the second page or second side of the original onto the original glass, and then press the [Start] key. – To scan the remaining pages in the original, repeat step 7. 4-16 bizhub 750/600 (Phase 2)
  • Page 135 Basic copy operations After all original pages have been scanned, touch [Finish]. Press the [Start] key. bizhub 750/600 (Phase 2) 4-17...

  • Page 136: Specifying Original Settings

    Slide the adjustable paper guides against the edges of the original. – Load the document pages into the ADF so that the top of the pages is toward the back or the left side of the machine. 4-18 bizhub 750/600 (Phase 2)
  • Page 137 Basic copy operations In the Basic screen, touch [Combine Originals]. The Combine Originals screen appears. Touch [Mixed Original]. – To cancel the "Mixed Original" setting, touch [Mixed Original] again to deselect it. bizhub 750/600 (Phase 2) 4-19...

  • Page 138: Positioning Folded (Z-Folded) Original

    Position the original to be copied. – For details on loading the original, refer to "To position the original into the ADF" on page 4-9. In the Basic screen, touch [Combine Originals]. The Combine Originals screen appears. 4-20 bizhub 750/600 (Phase 2)
  • Page 139 Basic copy operations Touch [Z-Folded Original]. – To cancel the "Z-Folded Original" setting, touch [Z-Folded Original] again to deselect it. bizhub 750/600 (Phase 2) 4-21...

  • Page 140: Positioning Tabbed Original

    For details, refer to "Specifying paper settings for paper trays" on page 8-26 or "Loading paper into the bypass tray" on page 3-48. In the Basic screen, touch [Combine Originals]. The Combine Originals screen appears. 4-22 bizhub 750/600 (Phase 2)
  • Page 141 Basic copy operations Touch [Tab Original]. The Tab Original Size screen appears. Touch the button for the size of the positioned original. Touch [OK]. bizhub 750/600 (Phase 2) 4-23...

  • Page 142: Selecting The Original Orientation (Original Direction Settings)

    • Select this setting for an original placed on the original glass with the top of the original toward the right side of this machine. 4-24 bizhub 750/600 (Phase 2)
  • Page 143 • Select this setting for an original placed on the original glass with the top of the original toward the left side of this machine. bizhub 750/600 (Phase 2) 4-25...

  • Page 144: To Specify An Original Direction Setting

    0 For details on positioning the document, refer to "Positioning the original" on page 4-9. Position the original to be copied. In the Basic screen, touch [Combine Originals]. The Combine Originals screen appears. Touch [Original Direction]. The Original Direction screen appears. 4-26 bizhub 750/600 (Phase 2)
  • Page 145 Basic copy operations Touch the button for the orientation of the positioned original, and then touch [OK]. – To cancel changes to the settings, touch [Cancel]. bizhub 750/600 (Phase 2) 4-27...

  • Page 146: Selecting The Position Of The Binding Margin (Margin Settings)

    Select this setting if the original is posi- tioned with the binding margin at the right. Select this setting if the original is posi- tioned with the binding margin at the top. 4-28 bizhub 750/600 (Phase 2)
  • Page 147 If the original length is more than 297 mm, a binding position along the short side of the paper is selected. When the original length is more than 297 mm: bizhub 750/600 (Phase 2) 4-29...

  • Page 148: To Specify A Margin Setting

    When loading an original with a binding margin, position the top of the original toward the back of the machine. In the Basic screen, touch [Combine Originals]. The Combine Originals screen appears. Touch [Margin]. The Page Margin screen appears. 4-30 bizhub 750/600 (Phase 2)
  • Page 149 Basic copy operations Touch the button for the desired margin position, and then touch [OK]. – To cancel changes to the settings, touch [Cancel]. bizhub 750/600 (Phase 2) 4-31...

  • Page 150: To Change Scan Settings For Each Document

    "Separate Scan" setting is used. Position the document to be copied. In the Basic screen, touch [Separate Scan]. Press the [Start] key. Scanning begins. Touch [Change Setting]. A screen appears, allowing you to change the settings. 4-32 bizhub 750/600 (Phase 2)
  • Page 151 The buttons that appear in the Change Setting screen differ depending on the specified settings. Settings for the following can be changed. Simplex/Duplex, Bind, Zoom, Frame Erase, Center Erase, Original Size – To cancel changes to the settings, touch [Cancel Change]. Simplex/Duplex screen bizhub 750/600 (Phase 2) 4-33...
  • Page 152 Basic copy operations Original Bind Position screen Zoom screen Frame erase screen 4-34 bizhub 750/600 (Phase 2)
  • Page 153 For details on specifying the Zoom setting, refer to "Specifying a zoom setting" on page 4-39. For details on specifying a zoom ratio, refer to "Erasing specified areas of copies ("Erase" functions)" on page 9-81. Density screen Original Type screen bizhub 750/600 (Phase 2) 4-35...

  • Page 154: Selecting A Paper Setting

    The amount of paper remaining is indicated in five levels. If special paper is selected, the special paper type is indicated with icons. For details, refer to "Icons that appear in the touch panel" on page 3-22. 4-36 bizhub 750/600 (Phase 2)

  • Page 155: Automatically Selecting The Paper Size ("Auto Paper Select" Setting)

    If the zoom ratio was increased or decreased, a paper size that corresponds to the specified zoom ratio is automatically selected. In the Basic screen, touch [Paper]. The Paper screen appears. Touch [Auto Paper Select]. Touch [OK]. The Basic screen appears again. bizhub 750/600 (Phase 2) 4-37...

  • Page 156: Manually Selecting The Desired Paper Size

    For details, refer to "Icons that appear in the touch panel" on page 3-22. In the Basic screen, touch [Paper]. The Paper screen appears. Select the paper tray loaded with the desired paper. Touch [OK]. The Basic screen appears again. 4-38 bizhub 750/600 (Phase 2)

  • Page 157: Specifying A Zoom Setting

    If the "Auto Paper Select" setting was selected, the Paper screen appears. In the Paper screen, specify the desired Paper setting. In the Basic screen, touch [Zoom]. The Zoom screen appears. Touch [Auto Zoom]. bizhub 750/600 (Phase 2) 4-39...
  • Page 158 Basic copy operations Touch [OK]. The Basic screen appears again. 4-40 bizhub 750/600 (Phase 2)

  • Page 159: Specifying The Same Zoom Ratio As The Original ("×1.0" Setting)

    0 Touch [+] to enlarge the zoom ratio, and touch [–] to reduce the zoom ratio in e0.001 intervals. In the Basic screen, touch [Zoom]. The Zoom screen appears. Touch [×1.0]. Touch [OK]. The Basic screen appears again. bizhub 750/600 (Phase 2) 4-41...

  • Page 160: Slightly Reducing The Copy ("Minimal" Setting)

    For details on changing the zoom ratio for the "Minimal" setting, refer to "Storing the desired zoom ratio" on page 4-51. In the Basic screen, touch [Zoom]. The Zoom screen appears. Touch [Minimal]. Touch [OK]. The Basic screen appears again. 4-42 bizhub 750/600 (Phase 2)

  • Page 161: Selecting A Preset Zoom Ratio (Enlarge And Reduce Settings)

    In the Basic screen, touch [Zoom]. The Zoom screen appears. Touch the button for the appropriate zoom ratio according to the original and paper sizes. Touch [OK]. The Basic screen appears again. bizhub 750/600 (Phase 2) 4-43...

  • Page 162: Typing In The Zoom Ratio (Xy Zoom Setting)

    0 The entered zoom ratio can be stored. For details on storing the zoom ratio, refer to "Storing the desired zoom ratio" on page 4-51. In the Basic screen, touch [Zoom]. The Zoom screen appears. Touch [XY Zoom]. The Zoom screen appears. 4-44 bizhub 750/600 (Phase 2)
  • Page 163 Touch the button under "XY Zoom", and then use the keypad to type in the desired zoom ratio. – To cancel changes to the settings, touch [Cancel]. Touch [OK] twice. The Basic screen appears again. bizhub 750/600 (Phase 2) 4-45...

  • Page 164: Typing In Separate X And Y Zoom Ratios (Independent Zoom Settings)

    Error" appears. Type in a value within the allowable range. If the value was incorrectly entered, press the [C] (clear) key to erase the value, and then specify the correct value. In the Basic screen, touch [Zoom]. The Zoom screen appears. 4-46 bizhub 750/600 (Phase 2)
  • Page 165 Basic copy operations Touch [XY Zoom]. Touch [X] under "Set Individual Zoom", and then use the keypad to type in the desired zoom ratio (between e0.250 and e4.000) for the X direction. bizhub 750/600 (Phase 2) 4-47...
  • Page 166 (between e0.250 and e4.000) for the Y direction. – To cancel changes to the settings, touch [Cancel]. Touch [OK], and then touch [OK] in the next screen that appears. The Basic screen appears again. 4-48 bizhub 750/600 (Phase 2)

  • Page 167: Selecting A Stored Zoom Ratio

    (between e0.250 and e4.000). For details on storing zoom ratios, refer to "Storing the desired zoom ratio" on page 4-51. In the Basic screen, touch [Zoom]. The Zoom screen appears. Touch the button for the desired zoom ratio under "Set Zoom". bizhub 750/600 (Phase 2) 4-49...
  • Page 168 Basic copy operations Touch [OK]. The Basic screen appears again. 4-50 bizhub 750/600 (Phase 2)
  • Page 169 0 To store a "Minimal" zoom ratio, type in the desired zoom ratio between e0.900 and e0.999. In the Basic screen, touch [Zoom]. The Zoom screen appears. Touch [XY Zoom]. The Zoom screen appears. bizhub 750/600 (Phase 2) 4-51...
  • Page 170 Touch the button or [Minimal] where the new zoom ratio is to be stored. – To cancel changes to the settings, touch [Cancel]. The specified zoom ratio is stored. Touch [OK], and then touch [OK] in the next two screens that appear. The Basic screen appears again. 4-52 bizhub 750/600 (Phase 2)

  • Page 171: Selecting A Simplex/Duplex Setting (1-Side/2-Sides Settings)

    Select this setting to produce one double-sided copy from two single-sided original. Select this setting to produce two single-sided cop- ies from one double-sided original. Select this setting to produce double-sided copies from double-sided original. bizhub 750/600 (Phase 2) 4-53...

  • Page 172: To Select Single-Sided Copies

    0 For details on using the original glass to scan multiple original pages, refer to "Scanning a multi-page original from the original glass" on page 4-15. In the Basic screen, touch [Simplex/Duplex]. The Simplex/Duplex screen appears. Touch [1 1] or [2 4-54 bizhub 750/600 (Phase 2)
  • Page 173 Touch [Original Direction], select the orientation of the loaded document, and then touch [OK]. – For details on specifying the original orientation, refer to "Selecting the original orientation (Original Direction settings)" on page 4-24. Touch [OK]. The Basic screen appears again. bizhub 750/600 (Phase 2) 4-55...

  • Page 174: To Select Double-Sided Copies

    For details on specifying the original orientation, refer to "Selecting the original orientation (Original Direction settings)" on page 4-24. In the Basic screen, touch [Simplex/Duplex]. The Simplex/Duplex screen appears. Touch [1 2] or [2 4-56 bizhub 750/600 (Phase 2)
  • Page 175 If the original length is more than 297 mm, a binding position along the short side of the paper is selected. Touch [OK]. The Basic screen appears again. bizhub 750/600 (Phase 2) 4-57...

  • Page 176: Selecting The Quality Of The Original

    (such as that written with a pencil). The copied text is reproduced so that it is darker, providing text that is easy to read. Dot Matrix The following procedure describes how to select an Orig. Image Type setting. 4-58 bizhub 750/600 (Phase 2)

  • Page 177: To Specify An Orig. Image Type Setting

    For an original that contains photos, touch [Photo]. – For an original that contains both text and photos, touch [Text/Photo]. – For an original that contains faint text, touch [Dot Matrix]. The Original Image Type screen appears again. bizhub 750/600 (Phase 2) 4-59...
  • Page 178 Basic copy operations Detail To cancel a setting, touch the button for a setting different from the currently selected setting. 4-60 bizhub 750/600 (Phase 2)

  • Page 179: Specifying The Density Settings

    Touch [Std.] to select the middle setting of the nine levels. The following procedures describe how to specify the density settings. Adjusting the print density (Density settings) In the Basic screen, touch [Density]. The Density screen appears. bizhub 750/600 (Phase 2) 4-61...
  • Page 180 Each time [Light] or [Dark] is touched, the density is lightened or darkened by one level. – To select the middle of the nine levels, touch [Std.]. – Touch [Auto] to automatically adjust the level of the density according to the document being copied. Touch [OK]. 4-62 bizhub 750/600 (Phase 2)

  • Page 181: Adjusting The Background Density (Adjust Background Settings)

    Select the desired background density setting. – Each time [Light] or [Dark] is touched, the density is lightened or darkened by one level. – To select the middle of the nine levels, touch [Std.]. Touch [OK]. bizhub 750/600 (Phase 2) 4-63...

  • Page 182: Selecting A Combine Originals Setting

    "×1.0", Enlarge, Reduce, or XY Zoom (XY Zoom and Independent Zoom) settings. To use the settings together, set the "Auto Zoom for Combine/Booklet" parameter in Utility mode to "OFF". For details, refer to "Copier setting" on page 13-33. 4-64 bizhub 750/600 (Phase 2)
  • Page 183 8 in 1 Select this setting to print eight original pages on one page. The page arrangement (Numbering Direction settings) can be specified. <Horizontal> <Vertical> The following procedure describes how to select a Combine Originals setting. bizhub 750/600 (Phase 2) 4-65...

  • Page 184: Copying Multiple Original Pages Onto A Single Page (Combine Originals)

    Select the page arrangement according to the orientation and number of pages. – If "4 in 1" or "8 in 1" was selected, the page arrangement for "Vertical" and "Horizontal" can be viewed in the sub display area. 4-66 bizhub 750/600 (Phase 2)
  • Page 185 Basic copy operations – If "4 in 1" or "8 in 1" was selected, touch [Horizontal] or [Vertical] to specify the page arrangement. – To cancel the setting, touch the button again to deselect it. bizhub 750/600 (Phase 2) 4-67...

  • Page 186: Selecting Finishing Settings

    "Selecting the position of the binding margin (Margin settings)" on page 4-28. If post inserter PI-501 is installed onto finisher FS-504/FS-505/FS-602, the finisher can be operated manually. For details, refer to "Using finisher manually" on page 4-95. 4-68 bizhub 750/600 (Phase 2)
  • Page 187 (Refer to page 4-68, p. 4-73.) <If a finisher is installed> The copies are fed out and stacked on top of each other with each set shifted to separate it. (Refer to page 4-68, p. 4-73.) bizhub 750/600 (Phase 2) 4-69...
  • Page 188 (Refer to page 4-76.) Punch Select this setting to punch holes (2 or 4 holes) in the copies for filing them. (Refer to page 4-82.) The following procedures describe how to select Finishing settings. 4-70 bizhub 750/600 (Phase 2)

  • Page 189: Separating Copies By Sets ("Sort" Setting)

    0 If "Offset" is selected while a finisher is installed, printed copies are fed out and stacked on top of each other with each set shifted to separate it. In the Basic screen, touch [Finishing]. The Finishing screen appears. bizhub 750/600 (Phase 2) 4-71...
  • Page 190 Basic copy operations Touch [Sort]. – To separate each set of copies, touch [Offset]. To cancel the setting, touch [Offset] again to deselect it. Touch [OK]. The Basic screen appears again. 4-72 bizhub 750/600 (Phase 2)

  • Page 191: Separating Copies By Pages ("Group" Setting)

    0 If "Offset" is selected while a finisher is installed, printed copies are fed out and stacked on top of each other with each set shifted to separate it. In the Basic screen, touch [Finishing]. The Finishing screen appears. bizhub 750/600 (Phase 2) 4-73...
  • Page 192 Basic copy operations Touch [Group]. – To separate each set of pages, touch [Offset]. To cancel the "Offset" setting, touch [Offset] again to deselect it. Touch [OK]. The Basic screen appears again. 4-74 bizhub 750/600 (Phase 2)

  • Page 193: Feeding Out Copies Face Up ("Face Up" Setting)

    Printed copies are fed out face down. – To cancel the setting, touch [Face Up] again to deselect it. – To cancel changes to the settings, touch [Cancel]. Touch [OK]. The Basic screen appears again. bizhub 750/600 (Phase 2) 4-75...

  • Page 194: Stapling Copies (Staple Settings)

    For details on specifying the original orientation, refer to "Selecting the original orientation (Original Direction settings)" on page 4-24. 4-76 bizhub 750/600 (Phase 2)
  • Page 195 41 to 50 sheets 20 sets A3 w 2 to 9 sheets 50 sets 10 to 20 sheets 50 sets 21 to 30 sheets 30 sets 31 to 40 sheets 25 sets 41 to 50 sheets 20 sets bizhub 750/600 (Phase 2) 4-77...
  • Page 196 50 sets 10 to 20 sheets 50 sets 21 to 30 sheets 30 sets 31 to 40 sheets 25 sets 41 to 50 sheets 20 sets 51 to 60 sheets — 61 to 100 sheets — 4-78 bizhub 750/600 (Phase 2)
  • Page 197 *1 Up to 50 sheets can be set for A3 size. *2 Up to 65 sheets can be set for B4 size. *3 51 to 100 sheets is only possible when the 100-sheet staple cartridge is installed. bizhub 750/600 (Phase 2) 4-79...

  • Page 198: To Bind Copies With Staples

    The Finishing screen appears. Under "Staple", touch either [Corner] or [2 Position]. – To cancel the Staple settings, touch [Corner] or [2 Position] again to deselect it. – To cancel changes to the settings, touch [Cancel]. 4-80 bizhub 750/600 (Phase 2)
  • Page 199 297 mm or less, the long side of the paper is stapled. If the original length(X) is more than 297 mm, the short side of the paper is stapled. Touch [OK] twice. The Basic screen appears again. bizhub 750/600 (Phase 2) 4-81...

  • Page 200: Punching Holes In Copies (Punch Settings)

    The procedure for selecting two punched holes is described below. When Finisher FS-504/FS-505/FS-602 and Punch PK-504/PK-505 are installed Paper weight Paper size 50g/m to 128g/ m A3 w, B4 w, A4 w, A4 v, B5 w, B5 v, A5 w, A5 v, Foolscap 4-82 bizhub 750/600 (Phase 2)

  • Page 201: To Punch Holes In Copies

    To separate each set of pages and punch them, touch [Offset]. To cancel the setting, touch [Offset] again to deselect it. – To cancel the Punch setting, touch [2-Hole] or [4holes] again to deselect it. – To cancel changes to the settings, touch [Cancel]. bizhub 750/600 (Phase 2) 4-83...
  • Page 202 If the original length is more than 297 mm, the holes are punched along the short side of the paper. – To cancel changes to the punched hole position, touch [Cancel]. Touch [OK] twice. The Basic screen appears again. 4-84 bizhub 750/600 (Phase 2)

  • Page 203: Specifying Folding Settings

    Z-Fold Select this setting to fold copies at the center, and then FS-504 fold them in half again before feeding them out. FS-505 (Z-folding unit ZU-601/ZU-602 must be installed.) FS-602 bizhub 750/600 (Phase 2) 4-85...
  • Page 204 Basic copy operations Setting Description Compatible models Tri-Fold Select this setting to fold copies in three before feed- FS-602 ing them out. 4-86 bizhub 750/600 (Phase 2)

  • Page 205: To Fold Copies At The Center ("Half Fold")

    The Folding screen appears. Touch [Half Fold]. – To cancel changes to the settings, touch [Cancel]. – To cancel the "Half Fold" setting, touch the button for a different setting. Touch [OK]. The Basic screen appears again. bizhub 750/600 (Phase 2) 4-87...
  • Page 206 Maximum 314 mm (width) e 458 mm (length) 80g/m to105g/ m 1 sheet Number of folded sheets Maximum number of sets 3 sheets (other than A4 w) 33 sets 3 sheets (A4 w) 25 sets 4-88 bizhub 750/600 (Phase 2)

  • Page 207: To Bind Copies At The Center ("Fold & Staple")

    In the Basic screen, touch [Folding]. The Folding screen appears. Touch [Fold & Staple]. – To cancel changes to the settings, touch [Cancel]. – To cancel the "Fold & Staple" setting, touch the button for a different setting. bizhub 750/600 (Phase 2) 4-89...
  • Page 208 Maximum number of sets 2 sheets to 5 sheets 20 sets * The number of sheets that can be bound together differs depending on the paper weight. 80 g/m paper: 20 sheets 105 g/m paper: 16 sheets 4-90 bizhub 750/600 (Phase 2)

  • Page 209: To Fold Copies Fanned ("Z-Fold")

    The Folding screen appears. Touch [Z-Fold]. – To cancel changes to the settings, touch [Cancel]. – To cancel the "Z-Fold" setting, touch the button for a different setting. Touch [OK]. The Basic screen appears again. bizhub 750/600 (Phase 2) 4-91...
  • Page 210 When finisher FS-504/FS-505/FS-602 and Z-folding unit ZU-601/ZU-602 are installed Paper weight Paper size Number of folded sheets 60 g/m to 80 g/m A3 w, B4 w 1 sheet Number of folded sheets Maximum number of sets 1 sheet 30 sets 4-92 bizhub 750/600 (Phase 2)

  • Page 211: To Fold Copies In Three ("Tri-Fold")

    The Folding screen appears. Touch [Tri-Fold]. – To cancel changes to the settings, touch [Cancel]. – To cancel the "Z-Fold" setting, touch the button for a different setting. Touch [OK]. The Basic screen appears again. bizhub 750/600 (Phase 2) 4-93...
  • Page 212 When finisher FS-602 and Z-folding unit ZU-601/ZU-602 are installed Paper weight Paper size Number of folded sheets 60g/m to 80g/ m A4 w 3 sheets 80g/m to105g/ m 1 sheet Number of folded sheets Maximum number of sets 1 sheet 50 sets 4-94 bizhub 750/600 (Phase 2)

  • Page 213: Using Finisher Manually

    - Finisher FS-505 + Post Inserter PI-501 + Punch kit PK-504/505 – Staple (Corner staple / 2 position staples) – Punch Reminder The Z folding unit ZU-601/602 cannot be used for manual punch. To use Punch mode manually, Punch kit PK-504/505 is necessary. bizhub 750/600 (Phase 2) 4-95...
  • Page 214 (80 g/m paper) with a thick cov- er paper Specifications A4R, 8.5"e11"R (60 to 105 g/m 3 sheets or less Folding mode for Tri-Fold tray Start/Stop button Fold&Staple Corner staple 2 position staples Tri-Fold Punch 4-96 bizhub 750/600 (Phase 2)

  • Page 215: To Use Finisher Manually

    Tri-Fold: Place the outside of the fold up. Lower tray Align the guide plate with the paper. Press Staple mode selection button and Punch button to select the desired mode. Start/Stop button Staple mode selection button Punch button bizhub 750/600 (Phase 2) 4-97...
  • Page 216 To select only the Punch mode, turn off all the other mode lamps. Press Start/Stop button. Do you want to stop the output operation? % Press Start/Stop button on the operation panel of Post Inserter. 4-98 bizhub 750/600 (Phase 2)

  • Page 217: Scanning The Next Original To Be Copied While A Copy Job Is Being Printed (Next Job Reservation)

    [Stop] key. For details, refer to "Performing operations on jobs" on page 12-7. Press the [Start] key to begin scanning and outputting the current copy job. The Basic screen for reserving a copy job appears. bizhub 750/600 (Phase 2) 4-99...
  • Page 218 After the current copy job is finished, the next copy job begins. – When the current copy job is finished, the copy settings for the next copy job are automatically displayed and the copy operation begins. 4-100 bizhub 750/600 (Phase 2)

  • Page 219: Stopping Scanning/Printing

    0 For details on deleting a stopped job, refer to "Deleting a stopped job" on page 4-102. Press the [Stop] key while a document is being scanned or a job is being printed. Scanning/printing stops. The Stopped Jobs screen appears. To resume all stopped jobs, press the [Start] key. bizhub 750/600 (Phase 2) 4-101...

  • Page 220: Deleting A Stopped Job

    Press the [Stop] key while an original is being scanned or a job is being printed. Scanning/printing stops. The Stopped Jobs screen appears. Select the job to be deleted, and then touch [Delete]. The selected job is deleted. 4-102 bizhub 750/600 (Phase 2)

  • Page 221: Additional Copy Operations

    Additional copy operations...

  • Page 223: Checking The Copy Settings (Mode Check)

    Additional copy operations Additional copy operations Checking the copy settings (Mode Check) From the Mode Check screens, the current copy settings can be checked and changed if desired. To check the settings Press the [Mode Check] key. bizhub 750/600 (Phase 2)
  • Page 224 Additional copy operations The Mode Check screen appears. After checking the settings, touch [Job End] or press the [Mode Check] key. The Basic screen appears again. bizhub 750/600 (Phase 2)
  • Page 225 To display the previous screen, touch [ Back]. To display the next screen, touch [Fwd. The buttons for functions where the setting has been changed from the default appear selected. bizhub 750/600 (Phase 2)

  • Page 226: To Change The Settings

    ] until the button for the function to be changed is displayed. Touch the button for the setting that you wish to change. The screen for specifying the setting appears. Follow the appropriate procedure to change the setting. bizhub 750/600 (Phase 2)

  • Page 227: Printing A Proof Copy To Be Checked (Proof Copy)

    Press the [Proof Copy] key. A single proof copy is printed. Check the sample copy. – If the sample copy was printed as desired, skip to step 7. – To change the copy settings, continue with step 5. bizhub 750/600 (Phase 2)
  • Page 228 Can the copy settings be changed? % The following copy settings can be specified after a sample copy is printed. # of Sets, 1-Sided/2-Sided, Finishing, Folding, Page Margin, Stamp/Overlay, Cover Mode, Insert Sheet, Chapters bizhub 750/600 (Phase 2)
  • Page 229 – To stop the proof copy while scanning or printing, perform the operation described in "Stopping scanning/printing" on page 4-101. – If multiple copies have been specified, another sample copy can be printed. bizhub 750/600 (Phase 2)
  • Page 230 Additional copy operations Touch [Print]. The remaining copies begin to be printed. 5-10 bizhub 750/600 (Phase 2)

  • Page 231: Interrupting A Copy Job (Interrupt Mode)

    Printing begins for the job that was interrupted. After the interrupting job is finished printing, press the [Interrupt] key. The indicator on the [Interrupt] key goes off, and Interrupt mode is canceled. The settings return to those specified before printing was interrupted. bizhub 750/600 (Phase 2) 5-11...
  • Page 232 Additional copy operations Note If the interrupting job is cancelled, printing for the interrupted job automatically restarts. 5-12 bizhub 750/600 (Phase 2)

  • Page 233: Registering Copy Programs (Mode Memory)

    Why is [Program Registration] not available? % If 30 copy programs have been registered, delete an unnecessary copy program. For details on deleting copy programs, refer to "To delete a copy program" on page 5-16. bizhub 750/600 (Phase 2) 5-13...
  • Page 234 How is a job deleted? % Touch the button for the desired copy program, and then touch [Del.]. In the screen that appears, requesting confirmation to delete the copy program, touch [Yes] to delete the selected copy program. 5-14 bizhub 750/600 (Phase 2)
  • Page 235 To stop registering the program, press the [Reset] key or the [Mode Memory] key. No matter which screen is displayed, the registration is cancelled. Otherwise, continue to touch [Cancel] until the Basic screen is displayed. bizhub 750/600 (Phase 2) 5-15...

  • Page 236: To Delete A Copy Program

    Touch [Del.]. A message appears, requesting confirmation to delete the copy program. Touch [Yes]. The Recall Copy Program screen appears again. The copy settings registered in the copy program are erased. 5-16 bizhub 750/600 (Phase 2)

  • Page 237: Copying With Programmed Copy Settings (Mode Memory)

    The Recall Copy Program screen appears. Touch the button for the copy program registered with the desired copy settings. – If the copy settings in the selected copy program are not to be checked, skip to step 8. bizhub 750/600 (Phase 2) 5-17...
  • Page 238 The Recall Copy Program screen appears again. Can different settings be displayed? % To display the previous screen, touch [ Back]. To display the next screen, touch [Fwd. Again touch the button for the program with the desired copy settings. 5-18 bizhub 750/600 (Phase 2)
  • Page 239 Copying begins with the recalled copy settings. Note To stop recalling the copy program, press the [Reset] key or the [Mode Memory] key, or touch [Cancel]. The copy settings cannot be changed from the Mode Check screens. bizhub 750/600 (Phase 2) 5-19...

  • Page 240: Displaying Function Descriptions (Help)

    Touch [Exit] to quit the Help mode and return to the screen that was displayed before the [Help] key was pressed. 5-20 bizhub 750/600 (Phase 2)
  • Page 241 The items displayed in the Help menu for the [Name and function of each part] differ depending on the options that are installed. To display the next screen higher in the menu structure, touch [ bizhub 750/600 (Phase 2) 5-21...
  • Page 242 To display the previous screen, touch [ Back]. To display the next screen, touch [Fwd. To view detailed descriptions (in the 4th level of the Help screens), touch [Detail], if it appears in the screen. 5-22 bizhub 750/600 (Phase 2)
  • Page 243 Press the key in the keypad for the number of the desired item in the Function Map screen. To return to the Help Menu screen, touch [ ] in the Help screen displayed by selecting an item in a Function Map screen. bizhub 750/600 (Phase 2) 5-23...

  • Page 244: To Display The Main Help Menu Screen

    Touch [Copy] or press the [1] key in the keypad. The Help Menu [Copy] screen appears. Is there more information about the buttons of the Help screens? % Refer to "Overview of help screens" on page 5-20. 5-24 bizhub 750/600 (Phase 2)
  • Page 245 Touch the button for the desired information or press the key in the keypad for the number to the left of the desired information to display the corresponding Help screen. After checking the Help information, touch [Exit] or press the [Help] key. The Basic screen appears again. bizhub 750/600 (Phase 2) 5-25...

  • Page 246: To Display The Help Screen While Specifying A Setting

    To return to the upper level Help Menu screen, touch [ ] in the Help screen displayed by selecting an item in a Function Map. The screen that was displayed before the [Help] key was pressed appears again. 5-26 bizhub 750/600 (Phase 2)

  • Page 247: Specifying Control Panel Settings (Accessibility Mode)

    Displaying the accessibility setting screen Press the [Accessibility] key. – To exit the Accessibility Setting screen and return to the Basic screen, touch [Close]. The Accessibility Setting screen appears. bizhub 750/600 (Phase 2) 5-27...

  • Page 248: To Set The "Key Repeat Start/Interval Time" Function

    Enlarge Display mode. Display the Accessibility Setting screen. (To display the screen, refer to page 5-27) Touch [Key Repeat Start/Interval Time] or press the [1] key in the keypad. The Key Repeat Start/Interval Time screen appears. 5-28 bizhub 750/600 (Phase 2)
  • Page 249 Enlarge Display mode, refer to the Enlarge Display Operations of the User manual. Detail To return to the Basic screen from the Accessibility Setting screen, press the [Accessibility] key or the [Reset] key. bizhub 750/600 (Phase 2) 5-29...

  • Page 250: To Set The "Enlarge Display Timer Setting" Function

    0 The "Enlarge Display Timer Setting" function is available only in Enlarge Display mode. Display the Accessibility Setting screen. (To display the screen, refer to page 5-27) Touch [Enlarge Display Timer Setting] or press the [2] key in the keypad. 5-30 bizhub 750/600 (Phase 2)
  • Page 251 The function and setting names and the illustrations are displayed at a larger size so that they can be seen more easily. For details on the Enlarge Display mode, refer to the [Enlarge Display Operations] of the User manual. bizhub 750/600 (Phase 2) 5-31...

  • Page 252: To Set The "Message Display Time" Function

    The factory default setting is "3 sec.". Display the Accessibility Setting screen. (To display the screen, refer to page 5-27) Touch [Message Display Time] or press the [3] key in the keypad. The Message Display Time screen appears. 5-32 bizhub 750/600 (Phase 2)
  • Page 253 Select whether messages are displayed for 3 seconds or for 5 seconds. – To cancel changes to the settings, touch [Cancel]. Touch [OK]. The Accessibility Setting screen appears again. Touch [Close] or press the [Accessibility] key. The Basic screen appears again. bizhub 750/600 (Phase 2) 5-33...

  • Page 254: To Set The "Accept Sound Setting" Function

    The factory default setting for "Accept Sound Setting" is "ON". Display the Accessibility Setting screen. (To display the screen, refer to page 5-27) Touch [Sound Setting] or press the [4] key in the keypad. The Sound Setting screen appears. 5-34 bizhub 750/600 (Phase 2)
  • Page 255 The Accept Sound Setting screen appears. Select the desired setting for "Accept Sound Setting". – To produce a sound, touch [ON]. To not produce a sound, touch [OFF]. – To cancel changes to the settings, touch [Cancel]. bizhub 750/600 (Phase 2) 5-35...
  • Page 256 Additional copy operations Touch [OK]. The Sound Setting screen appears again. Touch [OK]. The Accessibility Setting screen appears again. Touch [Close] or press the [Accessibility] key. The Basic screen appears again. 5-36 bizhub 750/600 (Phase 2)

  • Page 257: To Set The "Warning Sound" Function

    The factory default setting is "ON" for "Warning Sound Setting" and is "3 sec." for "Warning Sound Time". Display the Accessibility Setting screen. (To display the screen, refer to page 5-27) Touch [Sound Setting] or press the [4] key in the keypad. The Sound Setting screen appears. bizhub 750/600 (Phase 2) 5-37...
  • Page 258 Select the desired warning sound setting. – To produce a sound, touch [ON]. To not produce a sound, touch [OFF]. – Select the length of the warning sound. – To cancel changes to the settings, touch [Cancel]. 5-38 bizhub 750/600 (Phase 2)
  • Page 259 Additional copy operations Touch [OK]. The Sound Setting screen appears again. Touch [Close]. The Accessibility Setting screen appears again. Touch [Close], or press the [Accessibility] key. The Basic screen appears again. bizhub 750/600 (Phase 2) 5-39...

  • Page 260: To Set The "Sound Volume Setting" Function

    The factory default setting is "8" (middle setting). Display the Accessibility Setting screen. (To display the screen, refer to page 5-27) Touch [Sound Setting] or press the [4] key in the keypad. The Sound Setting screen appears. 5-40 bizhub 750/600 (Phase 2)
  • Page 261 Touch [Lower] or [Higher] to select the desired setting. – The volume can be set in 16 levels (between 0 and 16). – To cancel changes to the settings, touch [Cancel]. Touch [OK]. The Sound Setting screen appears again. bizhub 750/600 (Phase 2) 5-41...
  • Page 262 Additional copy operations Touch [OK]. The Accessibility Setting screen appears again. Touch [Close] or press the [Accessibility] key. The Basic screen appears again. 5-42 bizhub 750/600 (Phase 2)

  • Page 263: To Set The "Touch Panel Adj." Function

    The Touch Panel Adjustment screen appears. Why does the machine not respond when [Touch Panel Adj.] is touched? The touch sensors are not aligned on the touch panel. % Press the [5] key in the keypad. bizhub 750/600 (Phase 2) 5-43...
  • Page 264 Touch [Close] or press the [Accessibility] key. The Basic screen appears again. Note If the touch panel cannot be adjusted, contact the technical representative. Detail To cancel the touch panel adjustment, press the [Stop] key or the [Reset] key. 5-44 bizhub 750/600 (Phase 2)

  • Page 265: To Set The "Auto Reset Notification" Function

    Enlarge Display mode. The factory default setting is "OFF". Display the Accessibility Setting screen. (To display the screen, refer to page 5-27) Touch [Auto Reset Notification] or press the [6] key in the keypad. bizhub 750/600 (Phase 2) 5-45...
  • Page 266 [90 sec.] or [120 sec.]) for the length of time that the message is to be displayed. – To cancel changes to the settings, touch [Cancel]. Touch [OK]. The Accessibility Setting screen appears again. Touch [Close], or press the [Accessibility] key. The Basic screen appears again. 5-46 bizhub 750/600 (Phase 2)
  • Page 267 Enlarge Display mode is given priority and the message requesting confirmation to reset the settings in Enlarge Display mode is not displayed. bizhub 750/600 (Phase 2) 5-47...

  • Page 268: To Set The "Enlarge Display Confirmation Screen" Function

    To set the "Enlarge Display Confirmation Screen" function When the [Enlarge Display] key is pressed to change the display of the screen, a message can be displayed, requesting confirmation to reset the settings to their defaults. The factory default setting is "No". 5-48 bizhub 750/600 (Phase 2)
  • Page 269 Touch [Enlarge Display Confirmation Screen] or press the [7] key in the keypad. The Enlarge Display Confirmation Screen screen appears. Select whether or not the message is displayed. – To cancel changes to the settings, touch [Cancel]. bizhub 750/600 (Phase 2) 5-49...
  • Page 270 For details on the Enlarge Display mode, refer to the User manual [Enlarge Display Operations]. If [No] is touched in the message requesting confirmation to enter Enlarge Display mode, the screens are not changed. 5-50 bizhub 750/600 (Phase 2)

  • Page 271: Troubleshooting

    Troubleshooting...

  • Page 273: When The Message "Malfunction Detected." Appears (Call Technical Representative)

    (call technical representative screen) The phone number and fax number for the usual technical representative appears in the center of the call technical representative screen. Display in Enlarge Display mode If a malfunction occurs, the screen shown below appears. bizhub 750/600 (Phase 2)
  • Page 274 Troubleshooting Touch to display the message shown in the following illustration. bizhub 750/600 (Phase 2)

  • Page 275: To Call The Technical Representative

    Contact the technical representative, and inform them of the malfunction code. Reminder Since the machine may be damaged, contact the technical representative according to the procedure described above as soon as the call technical representative screen appears. bizhub 750/600 (Phase 2)
  • Page 276 Center is automatically notified of the malfunction code. After the message "Malfunction was detected. CS Remote Care has called the Service Center." appears, turn off the sub power switch and the main power switch, and then unplug the machine from the electrical outlet. bizhub 750/600 (Phase 2)

  • Page 277: When The Message "Misfeed Detected." Appears

    The illustration above shows all "o" and arrows displayed; however, normally, all marks will not appear. Error codes may appear in the illustration description area of the JAM location display screen. For details, contact your technical representative. bizhub 750/600 (Phase 2)

  • Page 278: To Clear A Paper Misfeed

    Clear the paper misfeed according to the instructions that appear in the screen. – When removing misfeed paper, be careful that the paper does not tear and remain in the machine. – Do not touch or scratch the surface of the drum. bizhub 750/600 (Phase 2)
  • Page 279 Parts in the fusing unit on the left side inside the machine are extremely hot. In order to reduce the risk of burns, do not touch any part in this unit when clearing paper misfeeds. bizhub 750/600 (Phase 2)

  • Page 280: When The Message "Replenish Paper." Appears

    Troubleshooting When the message "Replenish paper." appears If a tray has run out of paper while copying or after printing, the message "Replenish paper." appears. 6-10 bizhub 750/600 (Phase 2)

  • Page 281: To Replenish Paper

    1 or 2" on page 3-44, "Loading paper into the tray 3 or 4" on page 3-46, "Loading paper into the bypass tray" on page 3-48, and "Loading paper into the LCU (LU-401/LU-402)" on page 3-51. bizhub 750/600 (Phase 2) 6-11...

  • Page 282: When The Message

    This message appears when the memory becomes full and scanning stops while scanning in Copy mode. To print all pages that have been scanned, touch [Print]. To delete the job for the scanned pages, touch [Delete]. Display in Enlarge Display mode 6-12 bizhub 750/600 (Phase 2)

  • Page 283: Memory Becomes Full While Queuing A Job

    Check the number of pages counted for the document, and then adjust the number of pages in the job to be queued. Display in Enlarge Display Mode bizhub 750/600 (Phase 2) 6-13...

  • Page 284: Simple Troubleshooting

    (See p. 3-44, p. 3-46, p. 3-48 and p. 3-51.) Was the document not Position the document so that it is pressed close enough pressed closely against the original against the original glass? glass. (See p. 4-11.) 6-14 bizhub 750/600 (Phase 2)
  • Page 285 Was paper that curls easily Remove the paper from the paper curled. (as with recycled paper) tray, turn it over, and then load it used? again. Replace the paper with paper that is not damp. bizhub 750/600 (Phase 2) 6-15...
  • Page 286 Copying is not possible Did the message "Your ac- Contact your administrator. even though the pass- count has reached its maxi- word is entered on a ma- mum allowance." appear? chine with user authentication/account track set. 6-16 bizhub 750/600 (Phase 2)

  • Page 287: Adf

    FS-504/FS- 505/FS-602) If any message other than those listed above appears, perform the operation described in the message. If the problem is not corrected after the described operation is performed, contact your technical representative. bizhub 750/600 (Phase 2) 6-17...

  • Page 288: Main Messages And Their Remedies

    Since the toner has run out, Replace the toner cartridge. tridge. the machine is unable to make copies. Stapler empty. Replace The staples have run out. Replace the staple cartridge. (See Staple Cartridge or can- p. 10-8.) cel Staple mode. 6-18 bizhub 750/600 (Phase 2)
  • Page 289 Representative. panel. If any message other than those listed above appears, perform the operation described in the message. If the problem is not corrected after the described operation is performed, contact your technical representative. bizhub 750/600 (Phase 2) 6-19...
  • Page 290 Troubleshooting 6-20 bizhub 750/600 (Phase 2)

  • Page 291: Specifications

    Specifications...

  • Page 293: Bizhub 750/600

    Normal paper: 500 sheets (80g/m Bypass tray (universal tray): Normal paper: 100 sheets (80g/m Warm-up time bizhub 750: About 5 minutes bizhub 600: About 4 minutes and 30 seconds Image loss Leading edge/trailing edge : Less than 1.5 mm ± 1.5 mm (front side), 2.0 mm ±...
  • Page 294 600: 3.3 seconds or less Copy speed bizhub 750: 75 ppm (A4 v), 43 ppm (A3 w), 49 ppm (B4 w), 58 ppm (A4 w), 65 ppm (B5 w), 75 ppm (B5 v), 75 ppm (A5 v) bizhub 600: 60 ppm (A4 v), 35 ppm (A3 w), 40 ppm (B4 w),...

  • Page 295: Adf

    — — — B5 v — — — — A4 w — — A5 v — — B5 w — — — A5 w — — — — — — — o: Possible —: Not possible bizhub 750/600 (Phase 2)

  • Page 296: Option Specifications

    There are four F4 (Foolscap) sizes: 8-1/4 e 13 w, 8-1/8 e 13-1/4 w, 8- 1/2 e 13 w and 8 e 13 w. Any one of these sizes can be selected. For details, contact your technical representative. bizhub 750/600 (Phase 2)

  • Page 297: Finisher Fs-504

    Paper sizes (no. of bound pages): A3 w to B5v, A5 v (2 to 50 pages) Power requirements Supplied from main body Dimensions 424 mm (W) e 656 mm (D) e 990 mm (H) Weight Approx. 60 kg Consumables Staple cartridge bizhub 750/600 (Phase 2)

  • Page 298: Finisher Fs-505

    B4 w: 2 to 65 pages Other: 2 to 100 pages Power requirements Supplied from main body Dimensions 424 mm (W) e 656 mm (D) e 990 mm (H) Weight Approx. 60 kg Consumables Staple cartridge bizhub 750/600 (Phase 2)

  • Page 299: Finisher Fs-602

    Paper sizes (no. of bound pages): A3 w to A5 v (2 to 50 pages) Power requirements Supplied from main unit Dimensions 424 mm (W) e 656 mm (D) e 990 mm (H) Weight Approx. 65 kg Consumables Staples cartridge bizhub 750/600 (Phase 2)

  • Page 300: Punch Kit Pk-504/Pk-505

    Lower tray: A3 w to A5 v, Wide paper: Maximum 314 mm e 458 mm Paper capacity 200 sheets for both upper and lower trays Power requirements Supplied from finisher Dimensions 511 mm (W) e 620 mm (D) e 220 mm (H) Weight Approx. 10.5 kg 7-10 bizhub 750/600 (Phase 2)

  • Page 301: Security Kit Sc-501

    Paper tray labels User manuals 1 each User manual [Copy Operations] User manual [Enlarge Display Operations] User manual [Box Operations] User manual [Network Scanner Operations] Installation Manual Working table Internal heater Sub power supply display la- bels bizhub 750/600 (Phase 2) 7-11...
  • Page 302 Specifications 7-12 bizhub 750/600 (Phase 2)

  • Page 303: Copy Paper/Original

    Copy paper/original...

  • Page 305: Copy Paper

    "Offset" + "Sort" and "Offset" + "Group" settings: A3 w to B5 v Staple: A3 w to B5 v, A5 v Punch: A3 w to A5 w/v* Sub tray: "Sort" and "Group" settings: A3 w to B6 w, A6 w bizhub 750/600 (Phase 2)
  • Page 306 - 8-1/2 e 14 or F4 Select one size from the four F4 sizes available. For details, contact your technical representative. Available only when the optional punch kit PK-504/PK-505 or Z folding unit ZU-601/ZU-602 is installed. bizhub 750/600 (Phase 2)

  • Page 307: Paper Types And Paper Capacities

    — — (80 g/m paper) Tray 3 and 4 500 sheets — — (80 g/m paper) LU-401 4,000 sheets — — (80 g/m paper) LU-402 4,000 sheets — — (80 g/m paper) Double-sided copies — — bizhub 750/600 (Phase 2)

  • Page 308: Special Paper

    Select this setting when tab paper is loaded. A paper tray with this setting is not automatically se- lected when the "Auto Paper Select" setting is spec- ified or when the paper trays are switched automatically. bizhub 750/600 (Phase 2)
  • Page 309 "Auto Paper Select" setting is spec- ified or when the paper trays are switched automatically. User settings can be changed so that the paper type can be selected automatically. For details, refer to "System setting" on page 13-26. bizhub 750/600 (Phase 2)

  • Page 310: Precautions For Paper

    - Store the paper laying flat, not standing on its edge. Curled paper may cause paper misfeeds. - Keep paper out of the reach of children. bizhub 750/600 (Phase 2)

  • Page 311: Automatic Tray Switching Feature

    When a different paper tray is automatically selected, the next paper tray is chosen from the priority list specified using the "Auto Tray Select Setting" parameter of Utility mode. Detail To change the order in which the paper trays are selected, refer to "System setting" on page 13-26. bizhub 750/600 (Phase 2)

  • Page 312: Specifying The Paper Setting For The Bypass Tray

    3-48. To automatically detect the paper size ("Auto Paper Select" setting) The size of the paper loaded into the bypass tray can be detected automatically. In the Basic screen, touch [Paper]. The Paper screen appears. 8-10 bizhub 750/600 (Phase 2)
  • Page 313 Copy paper/original Touch the button for the bypass tray, and then touch [Change Tray Settings]. Touch [Auto Detect]. Touch [OK] twice. The Basic screen appears again. Note The factory default setting is "Auto Detect". bizhub 750/600 (Phase 2) 8-11...

  • Page 314: To Specify A Paper Size (Standard Size Settings)

    The following procedure describes how to specify the setting for 8-1/2 e 11 paper loaded into the bypass tray. In the Basic screen, touch [Paper]. The Paper screen appears. Touch the button for the bypass tray, and then touch [Change Tray Settings]. 8-12 bizhub 750/600 (Phase 2)
  • Page 315 11]. × Touch [OK] three times. The Basic screen appears again. Reminder If paper other than the specified paper size is loaded, a paper misfeed may occur since the paper size is not automatically detected. bizhub 750/600 (Phase 2) 8-13...

  • Page 316: To Specify A Non-Standard Paper Size (Custom Size Settings)

    If non-standard-sized paper is loaded into the bypass tray, it will be necessary to specify the paper size. In the Basic screen, touch [Paper]. The Paper screen appears. Touch the button for the bypass tray, and then touch [Change Tray Settings]. 8-14 bizhub 750/600 (Phase 2)
  • Page 317 "Input Error" appears. Type in a value within the allowable range. – If the value was incorrectly entered, press the [C] (clear) key in the keypad to erase the value, and then specify the correct value. bizhub 750/600 (Phase 2) 8-15...
  • Page 318 % The names of the memory key can be changed. For details on changing the names, refer to "To store a non-standard paper size (Custom Size settings store)" on page 8-17. Touch [OK] three times. The Basic screen appears again. 8-16 bizhub 750/600 (Phase 2)

  • Page 319: To Store A Non-Standard Paper Size (Custom Size Settings Store)

    Storing paper sizes that are used often allows the paper size to be quickly selected, without having to re-enter the setting. In the Basic screen, touch [Paper]. The Paper screen appears. Touch the button for the bypass tray, and then touch [Change Tray Settings]. bizhub 750/600 (Phase 2) 8-17...
  • Page 320 "Input Error" appears. Type in a value within the allowable range. – If the value was incorrectly entered, press the [C] (clear) key in the keypad to erase the value, and then specify the correct value. 8-18 bizhub 750/600 (Phase 2)
  • Page 321 % To change the registered name, touch [Custom Name], and then touch the memory key to be renamed. % Use the keyboard that appeared in the screen to type in the new name, and then touch [OK] twice. bizhub 750/600 (Phase 2) 8-19...
  • Page 322 Copy paper/original % For details on typing in text, refer to "Entering text" on page 14-3. Touch [OK] four times. The Basic screen appears again. 8-20 bizhub 750/600 (Phase 2)

  • Page 323: To Select A Setting For Oversized Paper (Oversized Paper Settings)

    A3-size original to be printed. In the Basic screen, touch [Paper]. The Paper screen appears. Touch the button for the bypass tray, and then touch [Change Tray Settings]. bizhub 750/600 (Phase 2) 8-21...
  • Page 324 Select the size of the paper to be loaded and image adjustment. – To select a paper size in inches, touch [Inches]. The list of paper sizes in inches appears. To change the size, touch [Change Size]. The Change Size screen for oversized paper appears. 8-22 bizhub 750/600 (Phase 2)
  • Page 325 The selected size button is programmed with the entered paper size, so that the paper size is available to be selected again without having to be typed in. In addition, the size can be changed. bizhub 750/600 (Phase 2) 8-23...

  • Page 326: To Specify A Setting For Special Paper

    "Auto Paper Select" setting or the automatic tray switching feature. In the Basic screen, touch [Paper]. The Paper screen appears. Touch the button for the bypass tray, and then touch [Change Tray Settings]. 8-24 bizhub 750/600 (Phase 2)
  • Page 327 Touch [OK] twice. The Basic screen appears again. Reminder If overhead projector transparencies or thick paper is loaded into the bypass tray, be sure to select the corresponding paper type, otherwise a paper misfeed may occur. bizhub 750/600 (Phase 2) 8-25...

  • Page 328: Specifying Paper Settings For Paper Trays

    An item can also be selected by pressing the key in the keypad for the number beside the desired button. – For "2 User Setting", press the [2] key in the keypad. The User Setting screen appears. 8-26 bizhub 750/600 (Phase 2)
  • Page 329 [Utility/Counter] key. – Otherwise, cancel the Utility mode by touching [Close] in each screen until the screen for the Copy, Scan or Box mode appears. The System Setting screen appears. Touch [3 Paper Tray Setting]. bizhub 750/600 (Phase 2) 8-27...
  • Page 330 Copy paper/original The Paper Tray Setting screen appears. Note To change the paper size for paper loaded into the 1tray 1 and 2 and the LCU (LU-401/LU-402), contact your technical representative. 8-28 bizhub 750/600 (Phase 2)

  • Page 331: To Specify A Standard Paper Size (Standard Size 1 Settings)

    For details on changing the paper size for the tray 3 and 4, refer to "Loading paper of a different size into paper trays" on page 3-54. The Paper Type screen appears. Touch the button for the tray 3, and then touch [Paper Size]. The Paper Size screen appears. bizhub 750/600 (Phase 2) 8-29...
  • Page 332 Touch [Standard Size 1]. – The Paper Size screen that appears differs depending on the paper size type that is selected. Touch [OK]. If standard-sized paper is loaded into a paper tray, the paper size is automatically detected. 8-30 bizhub 750/600 (Phase 2)

  • Page 333: To Specify A Setting For Standard Special-Sized Paper (Standard Size 2 Settings)

    For details on changing the paper size for the tray 3 and 4, refer to "Loading paper of a different size into paper trays" on page 3-54. The Paper Type screen appears. Touch the button for the tray 3, and then touch [Paper Size]. The Paper Size screen appears. bizhub 750/600 (Phase 2) 8-31...
  • Page 334 – The Paper Size screen that appears differs depending on the paper size type that is selected. Buttons for the available paper sizes appear. Select the size of the paper to be loaded. Touch [OK]. 8-32 bizhub 750/600 (Phase 2)

  • Page 335: To Specify A Non-Standard Paper Size (Custom Size Settings)

    For details on changing the paper size for the tray 3 and 4, refer to "Loading paper of a different size into paper trays" on page 3-54. The Paper Type screen appears. Touch the button for the tray 3, and then touch [Paper Size]. The Paper Size screen appears. bizhub 750/600 (Phase 2) 8-33...
  • Page 336 – If the value was incorrectly entered, press the [C] (clear) key in the keypad to erase the value, and then specify the correct value. Touch [OK]. 8-34 bizhub 750/600 (Phase 2)

  • Page 337: To Select A Setting For Oversized Paper (Oversized Paper Settings)

    For details on changing the paper size for the tray 3 and 4, refer to "Loading paper of a different size into paper trays" on page 3-54. The Paper Type screen appears. Touch the button for the tray 3, and then touch [Paper Size]. The Paper Size screen appears. bizhub 750/600 (Phase 2) 8-35...
  • Page 338 – If the value was incorrectly entered, press the [C] (clear) key in the keypad to erase the value, and then specify the correct value. Select the desired image position. Touch [OK]. 8-36 bizhub 750/600 (Phase 2)

  • Page 339: To Specify A Paper Type

    For details on displaying the Paper Tray Setting screen, refer to "To display the paper tray setting screen" on page 8-26. The Paper Type screen appears. Touch the button for the tray 1, and then touch [Paper Type]. The Paper Type screen appears. bizhub 750/600 (Phase 2) 8-37...
  • Page 340 Copy paper/original Select the type of paper to be loaded. Touch [OK]. 8-38 bizhub 750/600 (Phase 2)

  • Page 341: Originals

    100 sheets (80 g/m paper) For documents of mixed sizes Single-Sided Original Double-Sided Original Original paper 50 g/m to 200 g/m type/Weight Original size Refer to "Mixed originals paper sizes". Paper capacity 100 sheets (80 g/m paper) bizhub 750/600 (Phase 2) 8-39...
  • Page 342 Original size A3, B4, A4 w/v, B5 w/v, A5 w/v 11 e 17, 8-1/2 e 11, 8 e 13 Paper capacity 100 sheets (80 g/m paper) Note Z-folded original can only be scanned using the ADF. 8-40 bizhub 750/600 (Phase 2)

  • Page 343: Precautions For Positioning Original Into The Adf

    - Original with binder holes - Original that have just been printed with this machine Reminder Before positioning folded original, such as those folded in half or in three, into the ADF, be sure to flatten the pages. bizhub 750/600 (Phase 2) 8-41...

  • Page 344: Original That Can Be Placed On The Original Glass

    - Do not place objects exceeding 6.8 kg on the original glass, otherwise the original glass may be damaged. - If a book is placed on the original glass, do not press it down extremely hard, otherwise the original glass may be damaged. 8-42 bizhub 750/600 (Phase 2)

  • Page 345: Application Functions

    Application functions...

  • Page 347: Inserting Paper Between Overhead Projector Transparencies ("Ohp Interleave" Function)

    The interleaf can be inserted blank or copied with the same image as that on the overhead projector transparency. Detail For details on loading overhead projector transparencies, refer to "Paper types and paper capacities" on page 8-5, "Loading paper into the bypass tray" on page 3-48. bizhub 750/600 (Phase 2)

  • Page 348: To Copy Using The "Ohp Interleave" Function

    Select "OHP" for the paper in the bypass tray. – Touch [Paper] in the Basic screen, touch the button for the bypass tray, touch [Change Tray Settings], and then touch [OHP]. Touch [OK]. The Paper screen appears. bizhub 750/600 (Phase 2)
  • Page 349 3 or 4" on page 3-46, and "Loading paper into the bypass tray" on page 3-48. Touch [Application]. The Application screen appears. Touch [Sheet/Cover/Chapter Insert]. – To cancel all settings for the Application functions, touch [Reset]. The Sheet/Cover/Chapter Insert screen appears. bizhub 750/600 (Phase 2)
  • Page 350 To cancel the "OHP Interleave" function, touch [OFF]. – To copy the document onto the interleaf, touch [Copy] under "Copy or Blank". Touch [OK] twice. If necessary, specify any other copy settings. Press the [Start] key. bizhub 750/600 (Phase 2)

  • Page 351: Inserting Copies Of A Different Original At A Specified Location ("Insert Image" Function)

    To cancel all settings for the Application functions, touch [Reset]. Reminder Position the original in order, starting with the first page. The copy will not be printed as desired if the original is position starting with the last page. bizhub 750/600 (Phase 2)

  • Page 352: To Copy Using The "Insert Image" Function

    To copy using the "Insert Image" function Load the main original (the one that the other original will be inserted into) into the ADF. Touch [Application]. The Application screen appears. Touch [Sheet/Cover/Chapter Insert]. The Sheet/Cover/Chapter Insert screen appears. bizhub 750/600 (Phase 2)
  • Page 353 Touch [Insert Image]. The Insert Image screen (for specifying settings) appears. Touch the buttons for the insert position setting. – To cancel changes to the settings, touch [Cancel]. – To cancel the "Insert Image" function, touch [OFF]. bizhub 750/600 (Phase 2)
  • Page 354 % Two insertion pages are added at the specified location. What will happen if the specified page number is greater than the number of pages in the original? % The insertion page is added at the end of the original. 9-10 bizhub 750/600 (Phase 2)
  • Page 355 Scanning of the original to be inserted begins. What should be done if there are multiple original to be inserted? % Repeat steps 11 and 12 until all original to be inserted are scanned. Touch [Finish]. Press the [Start] key. Printing begins. bizhub 750/600 (Phase 2) 9-11...

  • Page 356: Adding Cover Pages ("Cover Mode" Function)

    Back (Blank) Paper for the back cover sheet is added after the last page of the copy. The same operation is performed with double-sided copying. Front copy, Back copy Front blank, Back blank 9-12 bizhub 750/600 (Phase 2)

  • Page 357: To Copy Using The "Cover Mode" Function

    – Use paper with the same size for the cover pages and for the main body of the original, and load them in the same orientation. Touch [Application]. The Application screen appears. bizhub 750/600 (Phase 2) 9-13...
  • Page 358 The default setting for the paper tray loaded with cover pages can be specified from the Utility mode. For details, refer to "Copier setting" on page 13-33. – To cancel changes to the copy settings, touch [Cancel]. 9-14 bizhub 750/600 (Phase 2)
  • Page 359 Paper" and the "Back Cover Paper". – If a tray of the post inserter is selected, the original cannot be copied onto the cover pages. Instead, only blank pages will be inserted. Touch [OK] three times. bizhub 750/600 (Phase 2) 9-15...
  • Page 360 Application functions If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. 9-16 bizhub 750/600 (Phase 2)

  • Page 361: Inserting Cover Pages ("Insert Sheet" Function)

    "2 > 1" The front side of the 6th page of the original is copied as the 11th page of the copy and a blank page is inserted as the 12th page of the copy. bizhub 750/600 (Phase 2) 9-17...
  • Page 362 For details on positioning the document, refer to "Positioning the original" on page 4-9. For an original that exceeds 100 pages, refer "Scanning the original in separate batches ("Separate Scan" setting)" on page 4-13. To cancel all settings for the Application functions, touch [Reset]. 9-18 bizhub 750/600 (Phase 2)

  • Page 363: To Copy Using The "Insert Sheet" Function

    Use paper with the same size for the cover pages and for the main body of the original, and load them in the same orientation. Touch [Application]. The Application screen appears. Touch [Sheet/Cover/Chapter Insert]. The Sheet/Cover/Chapter Insert screen appears. bizhub 750/600 (Phase 2) 9-19...
  • Page 364 Application functions Touch [Insert Sheet]. The Insert Sheet screen (for specifying settings) appears. Touch the buttons for the insert position setting. Insert Sheet screen (for editing settings) 9-20 bizhub 750/600 (Phase 2)
  • Page 365 % Touch [Edit] to return to the Sheet Cover Insertion screen (with the list of specified pages). Touch the button for the page to be removed, and then press the [C] (clear) key in the keypad to remove the page number. bizhub 750/600 (Phase 2) 9-21...
  • Page 366 To cancel the "Insert Sheet" function, touch [OFF]. The Insert Paper screen appears. Touch the button for the paper tray loaded with the paper for the insertion. Touch [OK]. The Insert Sheet screen (for specifying settings) appears. 9-22 bizhub 750/600 (Phase 2)
  • Page 367 If "Blank" was selected, paper from the paper tray specified in step 10 is inserted after the specified page. Touch [OK] twice. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. bizhub 750/600 (Phase 2) 9-23...

  • Page 368: Specifying Pages To Be Printed On The Front Side ("Chapters" Function)

    When copying double-sided documents while using the "Chapters" function, each side of one page of the document is considered two separate pages. In addition, paper tray loaded with paper for specific pages can be specified. Single-sided original Final copy Double-sided original 9-24 bizhub 750/600 (Phase 2)
  • Page 369 For details on positioning the original, refer to "Positioning the original" on page 4-9. For an original that exceeds 100 pages, refer to "Scanning the original in separate batches ("Separate Scan" setting)" on page 4-13. To cancel all settings for the Application functions, touch [Reset]. bizhub 750/600 (Phase 2) 9-25...

  • Page 370: To Copy Using The "Chapters" Function

    Application functions To copy using the "Chapters" function Position the original to be copied. Touch [Application]. The Application screen appears. Touch [Sheet/Cover/Chapter Insert]. The Sheet/Cover/Chapter Insert screen appears. 9-26 bizhub 750/600 (Phase 2)
  • Page 371 Application functions Touch [Chapters]. The Chapters screen (for specifying settings) appears. Touch the buttons for the chapter position setting. Chapters screen (for editing settings) bizhub 750/600 (Phase 2) 9-27...
  • Page 372 % There is no change to the print result since the specified page is the same. How can the list of the last 15 specified page numbers be displayed instead of the list of the first 15 specified page numbers? % Touch [ ] or [ 9-28 bizhub 750/600 (Phase 2)
  • Page 373 Continue with step 12. – To cancel changes to the copy settings, touch [Cancel]. – To cancel the "Chapter" function, touch [OFF]. Touch [Chapter Paper]. The Chapter Paper screen appears. bizhub 750/600 (Phase 2) 9-29...
  • Page 374 The Chapters screen (for specifying settings) appears again. Touch [OK], and then touch [OK] in the next screen that appears. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. 9-30 bizhub 750/600 (Phase 2)

  • Page 375: Scanning Documents With Different Settings And Printing Copies All Together ("Program Job" Function)

    ("Program Job" function) Loaded document pages can be scanned with different settings and their copies can be printed together. Dokument 1 Dokument 2 Dokument 3 Note 100 document batches can be set. bizhub 750/600 (Phase 2) 9-31...

  • Page 376: To Copy Using The "Program Job" Function

    For details on positioning the original, refer to "Positioning the original" on page 4-9. Touch [Application]. The Application screen appears. Touch [Sheet/Cover/Chapter Insert]. – To cancel all settings for the Application functions, touch [Reset]. The Sheet/Cover/Chapter Insert screen appears. 9-32 bizhub 750/600 (Phase 2)
  • Page 377 To change the copy settings, select [Retry], and then touch [Change Setting]. – If the document is placed on the original glass, touch [Finish] in the screen that appears, requesting confirmation that scanning of the document is finished. bizhub 750/600 (Phase 2) 9-33...
  • Page 378 – To cancel changes to the settings, touch [Cancel Change]. Scanning begins. After scanning is finished, select [Fix], and then touch [OK]. Is there more information about the settings? % Refer to the appropriate section. 9-34 bizhub 750/600 (Phase 2)
  • Page 379 After all document pages have been scanned, touch [Finish]. A message appears, requesting confirmation that scanning is finished. Select [Yes], and then touch [OK]. – To change the copy settings, select [No], and then touch [Change Setting]. Specify any other desired copy settings. bizhub 750/600 (Phase 2) 9-35...
  • Page 380 Using the keypad, type in the desired number of copies. Touch [Execute] or press the [Start] key. – If [Cancel] is touched, a message appears, requesting confirmation to delete the data. To stop printing, select [Yes], and then touch [OK]. 9-36 bizhub 750/600 (Phase 2)

  • Page 381: Copying With Image Colors Inversed ("Neg-/Pos. Reverse" Function)

    For details on positioning the original, refer to "Positioning the original" on page 4-9. For an original that exceeds 100 pages, refer and "Scanning the original in separate batches ("Separate Scan" setting)" on page 4-13. Touch [Application]. The Application screen appears. bizhub 750/600 (Phase 2) 9-37...
  • Page 382 To cancel all settings for the Application functions, touch [Reset]. – To cancel the "Neg-/Pos. Reverse" function, touch [Neg-/Pos. Reverse] again. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. 9-38 bizhub 750/600 (Phase 2)

  • Page 383: Producing Separate Copies Of Each Page In A Page

    Front and Back Cover The front cover, separate copies of each page in the page spreads and the back cover are printed in the original page order. When "Separation" is selected 1>1 1>2 bizhub 750/600 (Phase 2) 9-39...
  • Page 384 Application functions When "Front Cover" is selected When "Front and Back Cover" is selected SURVEYOR’S REPORT SURVEYOR’S REPORT SURVEYOR’S REPORT SURVEYOR’S REPORT 9-40 bizhub 750/600 (Phase 2)

  • Page 385: To Copy Using The "Book Copy" Function

    % Scan the front cover, then the back cover, and then scan the remainder of the original. Load the paper to be used into the desired paper tray. Touch [Application]. The Application screen appears. bizhub 750/600 (Phase 2) 9-41...
  • Page 386 Application functions Touch [Book Copy/Repeat]. – To cancel all settings for the Application functions, touch [Reset]. The Book Copy/Repeat screen appears. Touch [Book Copy]. The Book Scanning screen appears. 9-42 bizhub 750/600 (Phase 2)
  • Page 387 Touch the button for the desired setting. – If necessary, touch [Erase] or [Center Erase] under "Book Erase". – To cancel changes to the settings, touch [Cancel]. – To cancel the "Book Copy" function, touch [OFF]. Erase screen Center erase screen bizhub 750/600 (Phase 2) 9-43...
  • Page 388 Touch [OK], and then touch [OK] in the next screen that appears. In the Basic screen, touch [Paper], and then select the paper tray loaded with the paper. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. 9-44 bizhub 750/600 (Phase 2)
  • Page 389 If "Front and Back Cover" was selected, the back cover is scanned after the front cover, and then all page spreads are scanned in order. – If "Front Cover" was selected, all page spreads are scanned in order after the front cover. Scanning begins. bizhub 750/600 (Phase 2) 9-45...
  • Page 390 What should be done if there are multiple pages in the original? % Position the next page and repeat step 11 until all pages of the document are scanned. After all original pages have been scanned, touch [Finish]. Press the [Start] key. Printing begins. 9-46 bizhub 750/600 (Phase 2)

  • Page 391: Repeating The Copy Image On A Sheet Of Paper ("Image Repeat" Function)

    The number of repeating copies of the image is detected. If the entire image does not fit within the specified area, the remaining areas are left blank as margins. Without Margin The number of repeating copies of the image is automatically detect- bizhub 750/600 (Phase 2) 9-47...
  • Page 392 Application functions "With Margin" setting Original "Without Margin" setting 2 Repeat Original 4 Repeat Original 8 Repeat Original 9-48 bizhub 750/600 (Phase 2)

  • Page 393: To Automatically Detect The Scanning Area ("Auto Original Size Detect")

    Load the paper to be used into the desired paper tray. Touch [Application]. The Application screen appears. Touch [Book Copy/Repeat]. – To cancel all settings for the Application functions, touch [Reset]. The Book Copy/Repeat screen appears. bizhub 750/600 (Phase 2) 9-49...
  • Page 394 To specify the desired number of repeats, refer to "To repeat the image the specified number of times ("Repeat")" on page 9-56. – To cancel changes to the settings, touch [Cancel]. – To cancel the "Image Repeat" function, touch [OFF]. 9-50 bizhub 750/600 (Phase 2)
  • Page 395 In the Basic screen, touch [Paper], and then select the paper tray loaded with the paper. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. bizhub 750/600 (Phase 2) 9-51...

  • Page 396: To Repeat The Specified Area ("Set Range")

    Load the paper to be used into the desired paper tray. Touch [Application]. The Application screen appears. Touch [Book Copy/Repeat]. – To cancel all settings for the Application functions, touch [Reset]. The Book Copy/Repeat screen appears. 9-52 bizhub 750/600 (Phase 2)
  • Page 397 Select the layout method. – To cancel changes to the settings, touch [Cancel]. – To cancel the "Image Repeat" function, touch [OFF]. Touch [Set Range], and then specify the scanning area. The Set Range screen appears. bizhub 750/600 (Phase 2) 9-53...
  • Page 398 If a value outside the allowable range is specified, the message "Input Error" appears. If "Input Error" appeared or if the value was incorrectly entered, press the [C] (clear) key to erase the value, and then specify the correct value. Touch [OK] three times. 9-54 bizhub 750/600 (Phase 2)
  • Page 399 For details, refer to "To repeat the image the specified number of times ("Repeat")" on page 9-56. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. bizhub 750/600 (Phase 2) 9-55...

  • Page 400: To Repeat The Image The Specified Number Of Times ("Repeat")

    Load the paper to be used into the desired paper tray. Touch [Application]. The Application screen appears. Touch [Book Copy/Repeat]. – To cancel all settings for the Application functions, touch [Reset]. The Book Copy/Repeat screen appears. 9-56 bizhub 750/600 (Phase 2)
  • Page 401 – For details on specifying a size, refer to "To repeat the specified area ("Set Range")" on page 9-52. The scanning area is detected, and the size appears under "Scan Range Original Size Setting". bizhub 750/600 (Phase 2) 9-57...
  • Page 402 If specify the distance from the center of the paper to each copy image after selecting "2 Repeat", continue with step 10. – If "4 Repeat" or "8 Repeat" was selected, continue with step 12. 9-58 bizhub 750/600 (Phase 2)
  • Page 403 To specify no distance, touch [No Shift]. Touch [OK]. If the distance between repeats was specified, the Repeat screen appears again. Touch [OK] three times. In the Basic screen, touch [Paper], and then select the paper tray loaded with the paper. bizhub 750/600 (Phase 2) 9-59...
  • Page 404 Application functions If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. 9-60 bizhub 750/600 (Phase 2)

  • Page 405: Copying An Original On Two Pages ("Booklet Pagination" Function)

    With single-sided copies, the pages are printed on two sheets of paper. With double-sided copies, the pages are printed on the front and back sides of a single sheet of paper. Reminder Position the original into the ADF. bizhub 750/600 (Phase 2) 9-61...

  • Page 406: To Copy Using The "Booklet Pagination" Function

    For an original that exceeds 100 pages, refer "Scanning the original in separate batches ("Separate Scan" setting)" on page 4-13. Touch [Application]. The Application screen appears. Touch [Book Copy/Repeat]. – To cancel all settings for the Application functions, touch [Reset]. The Book Copy/Repeat screen appears. 9-62 bizhub 750/600 (Phase 2)
  • Page 407 To cancel changes to the settings, touch [Cancel]. – To cancel the "Booklet Pagination" function, touch [OFF]. Touch [OK] twice. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. bizhub 750/600 (Phase 2) 9-63...

  • Page 408: Adding Filing Margins To Copies ("Page Margin" Function)

    "Right" setting "Left" setting "Top" setting Detail If the positions of the staples or punched holes are different from the binding position, the positions of the staples or punched holes are given priority. 9-64 bizhub 750/600 (Phase 2)

  • Page 409: To Copy Using The "Page Margin" Function

    For details on positioning the original, refer to "Positioning the original" on page 4-9. Touch [Application]. The Application screen appears. Touch [Page Margin]. – To cancel all settings for the Application functions, touch [Reset]. The Page Margin screen appears. bizhub 750/600 (Phase 2) 9-65...
  • Page 410 [C] (clear) key to erase the value, and then specify the correct value. How can the entered margin position be corrected? % Without changing the margin width, change the margin position. 9-66 bizhub 750/600 (Phase 2)
  • Page 411 Application functions Touch [OK]. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. bizhub 750/600 (Phase 2) 9-67...

  • Page 412: To Adjust The Position Of The Binding Margin ("Edit Margin" Setting)

    Place the original on the original glass. – For details on positioning the original, refer to "Positioning the original" on page 4-9. Touch [Application]. The Application screen appears. Touch [Page Margin]. The Page Margin screen appears. 9-68 bizhub 750/600 (Phase 2)
  • Page 413 For a horizontal shift, touch [Left] or [Right] to specify the shift direction. For a vertical shift, touch [Top] or [Bottom] to specify the shift direction. Both a horizontal shift and a vertical shift can be specified together. bizhub 750/600 (Phase 2) 9-69...
  • Page 414 If a value outside the allowable range is specified, the message "Input Error" appears. If "Input Error" appeared or if the distance was incorrectly entered, press the [C] (clear) key to erase the value, and then specify the correct value. 9-70 bizhub 750/600 (Phase 2)
  • Page 415 Touch [OK] three times. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. bizhub 750/600 (Phase 2) 9-71...

  • Page 416: Adjusting The Image To Fit The Paper (Image Adjustment Settings)

    The copy is printed without the image rotated to fit in the paper. Full Scan The copy is printed without margins at the edges of the paper. This allows the original to be copied with no loss if text is written to the edge of the paper. 9-72 bizhub 750/600 (Phase 2)
  • Page 417 4 mm from the bottom, and 2 mm on each side. If "Full Scan" is selected, the image is copied to the edges of the paper without erasing the areas mentioned above. "Centering" selected "No Rotate" selected Normal copy "Full Scan" selected bizhub 750/600 (Phase 2) 9-73...

  • Page 418: To Copy Using The Image Adjustment Settings

    4-9. Touch [Application]. The Application screen appears. Touch [Image Adjustment]. – To cancel all settings for the Application functions, touch [Reset]. The Image Adjustment screen appears. Select the desired Image Adjustment setting. 9-74 bizhub 750/600 (Phase 2)
  • Page 419 [Start] key is pressed. – If the original size does not appear under "Original Size" or to specify the original size, touch [Standard Size], and then specify the original size from any of the screens. bizhub 750/600 (Phase 2) 9-75...
  • Page 420 Can any size be specified? % Any size can be specified from the Custom Size screen. Touch [X] or [Y] to select the dimension, press the [C] (clear) key, and then use the keypad to specify the correct value. 9-76 bizhub 750/600 (Phase 2)
  • Page 421 Application functions Touch [OK] twice. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. bizhub 750/600 (Phase 2) 9-77...

  • Page 422: Copying Booklet Original ("Booklet" Function)

    Staple")" on page 4-89. For an original that exceeds 100 pages, refer "Scanning the original in separate batches ("Separate Scan" setting)" on page 4-13. The binding margin width is automatically specified. The "1>2" Simplex/Duplex setting is automatically selected. 9-78 bizhub 750/600 (Phase 2)

  • Page 423: To Copy Using The "Booklet" Function

    Load the paper to be used into the desired paper tray. Touch [Application]. The Application screen appears. Touch [Booklet Pagination]. – To cancel all settings for the Application functions, touch [Reset]. The Booklet screen appears. bizhub 750/600 (Phase 2) 9-79...
  • Page 424 "To adjust the position of the binding margin ("Edit Margin" setting)" on page 9-68. Touch [OK]. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. 9-80 bizhub 750/600 (Phase 2)

  • Page 425: Erasing Specified Areas Of Copies ("Erase" Functions)

    Unwanted areas on all four sides of the original are erased. Center Erase Shading that appears along the center of the original is erased. Non-Image Area Erase The size of the original is detected, and any area not part of the orig- inal is erased. bizhub 750/600 (Phase 2) 9-81...

  • Page 426: To Erase Specified Areas Of Copies ("Erase" Function)

    For details on positioning the original, refer to "Positioning the original" on page 4-9. Touch [Application]. The Application screen appears. Touch [Erase]. – To cancel all settings for the Application functions, touch [Reset]. The Erase screen appears. 9-82 bizhub 750/600 (Phase 2)
  • Page 427 "Frame". If "Frame" is selected, the same width is erased on all four sides of the original. Can the settings be combined? % "Frame" cannot be combined with the other settings ("Top", "Left", "Right" or "Bottom"). bizhub 750/600 (Phase 2) 9-83...
  • Page 428 Touch [OK], and then touch [OK] in the next screen that appears. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. 9-84 bizhub 750/600 (Phase 2)

  • Page 429: To Erase The Center Of Copies ("Center Erase" Function)

    For details on positioning the original, refer to "Positioning the original" on page 4-9. Touch [Application]. The Application screen appears. Touch [Erase]. – To cancel all settings for the Application functions, touch [Reset]. The Erase screen appears. bizhub 750/600 (Phase 2) 9-85...
  • Page 430 [C] (clear) key to erase the value, and then specify the correct value. – To cancel the "Center Erase" function, touch [OFF]. – To cancel changes to the settings, touch [Cancel]. 9-86 bizhub 750/600 (Phase 2)
  • Page 431 Application functions Touch [OK] twice. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. bizhub 750/600 (Phase 2) 9-87...

  • Page 432: To Erase Specified Areas Of Copies ("Non-Image Area Erase" Function)

    Be sure to fully open the ADF before making copies, otherwise the copies will not be produced correctly. Touch [Application]. The Application screen appears. Touch [Erase]. – To cancel all settings for the Application functions, touch [Reset]. The Erase screen appears. 9-88 bizhub 750/600 (Phase 2)
  • Page 433 To cancel the "Non-Image Area Erase" function, touch [Non-Image Area Erase] again to deselect it. Touch [OK]. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. bizhub 750/600 (Phase 2) 9-89...

  • Page 434: Printing The Date/Time, Page Number Or Distribution Number On Copies ("Stamp/Overlay" Functions)

    A previously scanned image can be stored on the hard disk and re- called when needed to be printed overlapping a document. (Refer to page 9-111.) If the HDD is not installed, "Store Overlay" function is not available. 9-90 bizhub 750/600 (Phase 2)
  • Page 435 Application functions ’05/1/23 1:23PM Date/Time Page # Print Position URGENT Built-in Stamp Set Numbering Overlapping Overlapped document document Overlayed bizhub 750/600 (Phase 2) 9-91...
  • Page 436 Application functions Stored overlay image Overlapping Saved on document the hard disk Programmed overlay output Output Recalled Overlapped image overlapping Overlayed copy document image 9-92 bizhub 750/600 (Phase 2)

  • Page 437: To Display The Stamp/Overlay Screen

    For details on positioning the original, refer to "Positioning the original" on page 4-9. Touch [Application]. The Application screen appears. Touch [Stamp/Overlay]. – To cancel all settings for the Application functions, touch [Reset]. The Stamp/Overlay screen appears. bizhub 750/600 (Phase 2) 9-93...
  • Page 438 Application functions Select the desired Stamp/Overlay function. – The Stamp/Overlay functions can be used together. 9-94 bizhub 750/600 (Phase 2)

  • Page 439: Printing The Date/Time ("Date/Time" Function)

    Type" and "Pages". – To cancel changes to the settings, touch [Cancel]. – To cancel the "Date/Time" function, touch [OFF]. Can the time be omitted? % If "None" is selected, the time is not printed. bizhub 750/600 (Phase 2) 9-95...
  • Page 440 Select the desired direction under "Left & Right Adjustment" or "Top & Bottom Adjustment", and then use the keypad or touch [-] and [+] to specify the adjustment amount. – To make no left/right or up/down adjustments, touch [No Adj.]. 9-96 bizhub 750/600 (Phase 2)
  • Page 441 % To make no left/right or up/down adjustments, touch [No Adj.]. Touch [OK]. The Print Position screen appears again. Touch [OK] three times. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. bizhub 750/600 (Phase 2) 9-97...

  • Page 442: Printing The Page Number ("Page #" Function)

    When specifying a setting for "Start No.", switch the number between positive and negative by pressing the [ ] key. – To cancel changes to the settings, touch [Cancel]. – To cancel the "Page #" function, touch [OFF]. 9-98 bizhub 750/600 (Phase 2)
  • Page 443 (Blank)", the page number is counted, but the page is left blank. If "Skip the page(s)" is selected, the page number is not counted and the page is left blank. The sheet setting screen appears. bizhub 750/600 (Phase 2) 9-99...
  • Page 444 Application functions To specify settings for the pages to be printed on, and then touch [OK]. The Page # screen appears again. Touch [Print Position]. The Print Position screen appears. Select the printing position. 9-100 bizhub 750/600 (Phase 2)
  • Page 445 % To make no left/right or up/down adjustments, touch [No Adj.]. Touch [OK]. The Print Position screen appears. Touch [OK] two times. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. bizhub 750/600 (Phase 2) 9-101...

  • Page 446: Printing The Distribution Number ("Set Numbering" Function)

    The distribution number is normally printed as a four-digit number. If "Start Number" is set to "1", "0001" is printed. – To cancel changes to the settings, touch [Cancel]. – To cancel the "Set Numbering" function, touch [OFF]. 9-102 bizhub 750/600 (Phase 2)
  • Page 447 Touch [Change Size], and then select the character size. Touch [OK] twice. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. bizhub 750/600 (Phase 2) 9-103...

  • Page 448: Printing The Built-In Stamp ("Built-In Stamp" Function)

    The Built-In Stamp screen appears. Select the preset stamp. – Touch [Change Size], and then select the character size. – To cancel changes to the settings, touch [Cancel]. – To cancel the "Built-In Stamp" function, touch [OFF]. 9-104 bizhub 750/600 (Phase 2)
  • Page 449 If a value outside the allowable range is specified, the message "Input Error" appears. If "Input Error" appeared or if the value was incorrectly entered, press the [C] (clear) key to erase the value, and then specify the correct value. bizhub 750/600 (Phase 2) 9-105...
  • Page 450 Application functions Touch [OK] four times. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. 9-106 bizhub 750/600 (Phase 2)

  • Page 451: Printing The Preset Text At The Center Of The Copy Image ("Watermark" Function)

    Stamp/Overlay screen" on page 9-93. The Watermark screen appears. Select the preset text to be printed. – To cancel changes to the settings, touch [Cancel]. – To cancel the "Watermark" function, touch [OFF]. bizhub 750/600 (Phase 2) 9-107...
  • Page 452 Application functions Touch [OK] twice. The Watermark screen appears again. If necessary, specify any other copy settings. Using the keypad, type in the desired number of copies. Press the [Start] key. 9-108 bizhub 750/600 (Phase 2)

  • Page 453: Copying With An Overlapping Image ("Image Overlay" Function)

    Press the [Start] key. The loaded original is scanned. Position the original to be overlapped. – For an original that exceeds 100 pages, refer to "Scanning the original in separate batches ("Separate Scan" setting)" on page 4-13. bizhub 750/600 (Phase 2) 9-109...
  • Page 454 Application functions Press the [Start] key. The loaded original is scanned. Touch [Finish]. Press the [Start] key. 9-110 bizhub 750/600 (Phase 2)

  • Page 455: Storing An Overlapping Image And Overlay Copying ("Store Overlay" Function)

    In the Stamp/Overlay screen, touch [Store Overlay]. – For details on displaying the Stamp/Overlay screen, refer to "To display the Stamp/Overlay screen" on page 9-93. The Recall Image Overlay screen appears. Touch [Store Overlay Image]. bizhub 750/600 (Phase 2) 9-111...
  • Page 456 To specify where the overlay is to be stored, touch [Specify One- Touch], and then specify the desired location. – A maximum of 100 overlays can be stored. – If the name of the overlapping image already exists, a confirmation message appears. 9-112 bizhub 750/600 (Phase 2)
  • Page 457 Stamp/Overlay screen" on page 9-93. The Store Overlay screen appears. Recall the overlapping image. – Touch the button for the image to be recalled from the hard disk to select it, and then touch [OK]. bizhub 750/600 (Phase 2) 9-113...
  • Page 458 ("Separate Scan" setting)" on page 4-13. Using the keypad, type in the desired number of copies. Press the [Start] key. The loaded original is scanned. Touch [Finish]. Press the [Start] key. 9-114 bizhub 750/600 (Phase 2)

  • Page 459: Replacing Toner Cartridges And Staples And Emptying Dust Boxes

    Replacing toner cartridges and staples and emptying dust boxes...

  • Page 461: Replacing The Toner Cartridge

    Replace the toner cartridge. Detail It is recommended that the toner cartridge be replaced when the message "Toner Cartridge needs to be replaced." appears. When the message "Replace the toner" appears, the machine is stopped. bizhub 750/600 (Phase 2) 10-3...

  • Page 462: Display In Enlarge Display Mode

    Detail For details on replacing the toner cartridges, refer to "To replace the toner cartridge" on page 10-6. Display in Enlarge Display mode When the toner is empty, the screen shown below appears. 10-4 bizhub 750/600 (Phase 2)
  • Page 463 Be careful not to spill toner inside the machine or get toner on your clothes or hands. If your hands become soiled with toner, immediately wash them with soap and water. If toner gets in your eyes, immediately flush them with water, and then seek professional medical attention. bizhub 750/600 (Phase 2) 10-5...

  • Page 464: To Replace The Toner Cartridge

    – The toner within the toner cartridge may have become compacted. If it has, be sure to shake the toner cartridge until the toner is mostly broken up before installing the cartridge. 10-6 bizhub 750/600 (Phase 2)
  • Page 465 With the label at the end of the toner cartridge facing up, insert the bottom of the cartridge into the slot in the cartridge holder. Return the cartridge holder to its original position, and then close the toner cartridge door. bizhub 750/600 (Phase 2) 10-7...

  • Page 466: Replacing The Staples

    Replacing toner cartridges and staples and emptying dust boxes 10.2 Replacing the staples When finisher FS-504/FS-505/FS-602 is installed and is about to run out of staples, the message shown below appears. 10-8 bizhub 750/600 (Phase 2)

  • Page 467: Display In Enlarge Display Mode

    Be sure to replace the staple cartridge only after the message appears, otherwise the machine may be damaged. When staples run out in either of Saddle Staple Cartridge 1 or 2, the message "Replace Staple Cartridge 1" or "Replace Staple Cartridge 2" appears. bizhub 750/600 (Phase 2) 10-9...

  • Page 468: To Replace The Staple Cartridge For Finisher Fs-504/Fs-505

    Hold the lever on the staple cartridge, and then pull the cartridge down to remove it. Install the new staple cartridge. – Push up the staple cartridge, and then check that the cartridge is securely installed. 10-10 bizhub 750/600 (Phase 2)
  • Page 469 Replacing toner cartridges and staples and emptying dust boxes Return the stacker unit to its original position. Close the finisher door. bizhub 750/600 (Phase 2) 10-11...

  • Page 470: To Replace The Staple Cartridge For Finisher Fs-602

    Remove the staple cartridge. – While lifting the lever on the staple cartridge, pull the cartridge toward you to remove it. – Remove the staple cartridge by guiding it along the rails. 10-12 bizhub 750/600 (Phase 2)
  • Page 471 Install the staple cartridge. – Place the staple cartridge on the rails, and then guide it back to its original position. – Push down the staple cartridge, and then check that the cartridge is securely installed. bizhub 750/600 (Phase 2) 10-13...
  • Page 472 Replacing toner cartridges and staples and emptying dust boxes Return the stacker unit to its original position. Close the finisher door. Reminder Do not remove the remaining staples, otherwise the machine will not be able staple after the cartridge is replaced. 10-14 bizhub 750/600 (Phase 2)

  • Page 473: Emptying The Dust Boxes

    Emptying the dust boxes To empty the dust box of the punch kit If the punch dust box in punch kit PK-504/PK-505 installed on finisher FS-504/FS-505/FS-602 becomes full, the message shown below appears. Display in Enlarge Display Mode bizhub 750/600 (Phase 2) 10-15...
  • Page 474 Replacing toner cartridges and staples and emptying dust boxes Open the finisher door. Pull out the punch dust box. Empty the punch dust box. Install the punch dust box into its original position. 10-16 bizhub 750/600 (Phase 2)
  • Page 475 Replacing toner cartridges and staples and emptying dust boxes Close the finisher door. bizhub 750/600 (Phase 2) 10-17...

  • Page 476: To Empty The Dust Box Of The Z Folding Unit

    To empty the dust box of the Z folding unit If the punch dust box in Z folding unit ZU-601/ZU-602 installed on finisher FS-504/FS-505/FS-602 becomes full, the message shown below appears. Display in Enlarge Display mode 10-18 bizhub 750/600 (Phase 2)
  • Page 477 Replacing toner cartridges and staples and emptying dust boxes Open the finisher door. Pull out the punch dust box. Empty the punch dust box. Install the punch dust box into its original position. bizhub 750/600 (Phase 2) 10-19...
  • Page 478 Replacing toner cartridges and staples and emptying dust boxes Close the finisher door. 10-20 bizhub 750/600 (Phase 2)

  • Page 479: Care Of The Machine

    Care of the machine...

  • Page 481: Cleaning

    Never use solvents, such as benzene or thinner, to clean the main body. Original glass Clean the surface of the original glass by wiping it with a soft, dry cloth. Reminder Never use solvents, such as benzene or thinner, to clean the original glass. bizhub 750/600 (Phase 2) 11-3...

  • Page 482: Left Partition Glass

    Pressing too hard on the control panel or the touch panel may damage them. In addition, never use a mild household detergent, glass cleaner, benzene or thinner to clean the control panel or touch panel. 11-4 bizhub 750/600 (Phase 2)

  • Page 483: Adf Platen Guide Cover

    Never use solvents, such as benzene or thinner, to clean the ADF platen guide cover. Paper take-up roller Clean the paper take-up rollers by wiping them with a soft, dry cloth. Reminder Never use solvents, such as benzene or thinner, to clean the paper take- up roller. bizhub 750/600 (Phase 2) 11-5...

  • Page 484: Viewing Counters (Meter Count)

    In addition, the list of counters can be printed. To view the counters Press the [Utility/Counter] key. Touch [Details] in the sub display area. The list of counters appears. 11-6 bizhub 750/600 (Phase 2)
  • Page 485 % To print the list of counters, touch [Print], select the paper size and the "Simplex/Duplex" setting, and then press the [Start] key. Touch [Close]. The Basic screen appears again. Note The list of counters can be displayed even while the machine is copying or printing. bizhub 750/600 (Phase 2) 11-7...

  • Page 486: When The Message "Preventive Maintenance Time." Appears

    Care of the machine 11.3 When the message "Preventive maintenance time." appears If the message "Preventive maintenance time." appears, contact your technical representative and request a periodic maintenance inspection. 11-8 bizhub 750/600 (Phase 2)

  • Page 487: Managing Jobs (Job List)

    Managing jobs (Job list)

  • Page 489: Overview Of The Job List Screen

    - While one job is being printed, another job can be queued. A total of 78 jobs can be queued. - When one job is finished being printed, the next queued print job automatically begins. bizhub 750/600 (Phase 2) 12-3...

  • Page 490: Job List Screens

    - The function of each button in the Job List screens is described below. - A selected button indicates which job list is currently displayed. [Held Jobs], [Active Jobs], [Increase Priority], [Delete], and [Check Job] appear in the Current Jobs list on the Print tab. 12-4 bizhub 750/600 (Phase 2)
  • Page 491 [Scan] Displays the Scan tab of the Job List screen. For more details, refer to the Network Scanner Opera- tions of the bizhub 750/600 User manual. [RX/User Box] Displays the RX/User Box tab of the Job List screen. For more details, refer to the Network Scanner Opera- tions of the bizhub 750/600 User manual.
  • Page 492 Displays the number of pages in the original. # of Sets Displays the specified number of pages to be printed Result (Job History list only) Displays the result of the operation (Job Complete, Error Cleared, Deleted by User, Mode cancelled from conflict) 12-6 bizhub 750/600 (Phase 2)

  • Page 493: Performing Operations On Jobs

    – If an incorrect job was selected, select a different job or touch the button for the selected job again to deselect it. A message requesting confirmation to delete the job appears. bizhub 750/600 (Phase 2) 12-7...
  • Page 494 The screen that was displayed before [Job List] was touched appears again. Note If user authentication settings have been applied and the machine is set so that jobs cannot be deleted by other users, the job is not deleted. 12-8 bizhub 750/600 (Phase 2)

  • Page 495: To Check The Job Settings

    The number to the left of [ Back] indicates the number of the currently displayed screen/the total number of screens. – To display the previous screen, touch [ Back]. To display the next screen, touch [Fwd. bizhub 750/600 (Phase 2) 12-9...
  • Page 496 To finish checking the settings, touch [Close] or [Exit], or press the [Reset] key. – To return to the Job List screen, touch [Close]. – To return to the Basic screen, touch [Exit] or press the [Reset] key. 12-10 bizhub 750/600 (Phase 2)

  • Page 497: Displayed Information

    User Name, Time Stored, # of pgs., # of Sets, Output Tray, File Name Displayed only for jobs in the Current Jobs list Displayed only for jobs in the Job History list Displayed only for Current Jobs transmitted to multiple recipients bizhub 750/600 (Phase 2) 12-11...

  • Page 498: To Check The Job Details

    After the desired information has been checked, touch [Close] or [Exit] or press the [Reset] key. – To return to the Job List screen, touch [Close]. – To return to the Basic screen, touch [Exit] or press the [Reset] key. 12-12 bizhub 750/600 (Phase 2)
  • Page 499 Managing jobs (Job list) Detail To delete a queued job or job being performed, touch [Delete] in the Check Detail screen. bizhub 750/600 (Phase 2) 12-13...

  • Page 500: To Display Current Jobs (Held Jobs And Active Jobs Lists)

    "To print a stored job" on page 12-18. To give priority for output to a job, touch [Increase Priority] in the Active Jobs list. For more details, refer to "To increase priority for printing" on page 12-21. 12-14 bizhub 750/600 (Phase 2)

  • Page 501: To Display Job History

    Deleted Jobs: Displays only jobs that were deleted before they were finished – Finished Jobs: Displays only jobs that were correctly completed – Active Jobs: Displays all jobs The history of jobs of the selected type is displayed. bizhub 750/600 (Phase 2) 12-15...

  • Page 502: To Print A Sample Copy Of A Stored Job

    If the job that you wish to proof is not displayed, touch [ ] and ] until the desired job is displayed. – If an incorrect job was selected, touch the button for the selected job again to deselect it. 12-16 bizhub 750/600 (Phase 2)
  • Page 503 To exit the Release Held Job screen and return to the Active Jobs list in the Current Jobs list, touch [Cancel]. Detail To change the settings, touch [Change setting] in the Release Held Job screen. For details, refer to "To print a stored job" below. bizhub 750/600 (Phase 2) 12-17...

  • Page 504: To Print A Stored Job

    – To quit removing a stored job, touch [Cancel]. – To change the specified copy settings, continue with step 4. – To continue without changing the specified copy settings, skip to step 8. 12-18 bizhub 750/600 (Phase 2)
  • Page 505 The screen for the selected copy setting appears. Can the copy settings be changed? % The following copy settings can be specified after a sample copy is printed. # of Sets, 1-Sided/2-Sided, Finishing, Folding, Page Margin, Stamp/Overlay, Cover Mode, Insert Sheet, Chapters bizhub 750/600 (Phase 2) 12-19...
  • Page 506 In the Release Held Job screen, touch [OK]. The stored job appears in the Active Jobs list and is printed. How is the removal of a job from the Held Jobs list stopped? % Touch [Cancel]. 12-20 bizhub 750/600 (Phase 2)

  • Page 507: To Increase Priority For Printing

    Display the Active Jobs list in the Current Jobs list of the Print tab. Touch [Increase Priority]. The Increase Priority screen appears. bizhub 750/600 (Phase 2) 12-21...
  • Page 508 The selected job moves to the top of the list and printing of the job begins. How is the changing of the output priority stopped? % Touch [Cancel]. 12-22 bizhub 750/600 (Phase 2)

  • Page 509: Utility

    Utility...

  • Page 511: Overview Of Utility Mode

    For details on buttons marked with * or **, refer to page 13-56. For details on displaying buttons marked with ***, contact your technical representative. "(F)" indicates buttons that appear only when the fax kit is installed. For details, refer to the bizhub 750/600 User manual [Facsimile Operations]. Utility/Counter...
  • Page 512 [4] LCD Backlight Setting * [5] Power Low Power Save Setting* Mode Set- ting* Sleep Mode Setting* [6] Output [1] Print/Fax Print** Setting** Output Set- Fax** ting** [2] Output Tray Setting** [7] Original Image Densi- ty** 13-4 bizhub 750/600 (Phase 2)
  • Page 513 Dest. Display [5] Copy Copy Operat- Screen ing Screen [6] Fax Active TX Display Screen RX Display [7] Copy Ba- sic Screen Setting [8] Job List Default [3] Initial Set- ting (p. 13-32) bizhub 750/600 (Phase 2) 13-5...
  • Page 514 Insert Sheet* Separate Scan Output Settings Exit Direction Of 1 Sheet (Platen)* Image Rota- tion (Platen)* Tri-Fold Printed Side Selection* Print Jobs During Copy Operation** [5] Scanner Black Com- Setting pression (p. 13-36) Level 13-6 bizhub 750/600 (Phase 2)
  • Page 515 [2] Paper Paper Tray Setting Default Paper Size 2-Sided Print Bind Direc- tion Staple Hole-Punch Banner Paper Tray [3] PCL Set- [1] Font Set- ting ting [2] Symbol [3] Font Size [4] Line/Page [5] CR/LF Mapping bizhub 750/600 (Phase 2) 13-7...
  • Page 516 Entering Power Save Mode (Fax) [2] Output [1] Print/Fax Print Setting Output Set- tings [2] Exit Tray Setting [4] Offset Each Job Setting [5] Preset Characters Settings [3] Date/Time Setting [4] Daylight Saving Time Setting 13-8 bizhub 750/600 (Phase 2)
  • Page 517 Changing Access to Job Priority Job Settings Deleting Oth- er User’s Jobs Registering and Chang- Addresses Changing Zoom Ratio Changing the "From" Ad- dress Changing Im- age Overlay [4] Restrict Restrict Fax Operation Broadcasting Setting bizhub 750/600 (Phase 2) 13-9...
  • Page 518 (p. 13-39) [2] Erase Non Image Adjustment Area Erase Non Image Area Erase Setting ADF Frame Erase [3] Printer [1] Leading Adjustment Edge Adjust- ment [2] Centering [3] Vertical Adjust- ment*** [4] Horizontal Adjust- ment*** 13-10 bizhub 750/600 (Phase 2)
  • Page 519 [5] Punch Re- sist Loop Size [4] Z-Fold Po- [1] 1st Z- sition Adjust- Folded Posi- ment tion [2] 2nd Z- Folded Posi- tion [5] Tri-Fold Position [6] 2 Position Staple [7] Cover Sheet Tray Size bizhub 750/600 (Phase 2) 13-11...
  • Page 520 When Ac- count is changed When original is set on ADF When NEXT Staple Set- JOB is se- ting lected Original Set/Bind Di- rection Reset Data After Job [4] System Auto Reset for Proof Copy 13-12 bizhub 750/600 (Phase 2)
  • Page 521 Size De- tect ADF Original Size Detect Original Glass Small Size Detect Original Size Detect Change 1 Original Size Detect Change 2 Original Size Detect Change 3 Foolscap Size Setting 8K/16K Se- lect bizhub 750/600 (Phase 2) 13-13...
  • Page 522 [1] Pub- lic/Personal User Box [2] Bulletin Board User [3] Relay User [4] Annotation User Box [4] One- [1] Address Touch Regis- Book List tration List [2] Group List [3] Program List [4] E-Mail Subject/Text List 13-14 bizhub 750/600 (Phase 2)
  • Page 523 Authenti- cation [5] Counter List [5] Network [1] Network Setting Setting (p. 13-53) [2] TCP/IP Setting [3] NetWare Setting [4] http Set- ting [5] FTP Set- ting [6] SMB Set- ting [7] AppleTalk Setting bizhub 750/600 (Phase 2) 13-15...
  • Page 524 Setting [4] Total Counter Re- port Setting [5] PING Confirmation [6] SLP Set- ting [7] LPD Set- ting [8] Prefix/Suf- [1] ON/OFF fix Setting Setting [2] Prefix/Suf- fix Setting [9] Action for Invalid Certifi- cate 13-16 bizhub 750/600 (Phase 2)
  • Page 525 Tri-Fold Printed Side Selection [7] Printer [1] I/F Time- Setting (p. 13-55) [8] Fax Set- [1] Header In- ting formation [2] Head- Header Posi- er/Footer Po- tion sition Print Receiv- er’s Name Footer Posi- tion bizhub 750/600 (Phase 2) 13-17...
  • Page 526 Print Paper Selection Print Paper Size Incorrect User Box No. Entry Tray Selec- tion for RX Print Min Reduc- tion for RX Print Print Sepa- rate Fax Pag- File After Polling TX No. of Sets (RX) 13-18 bizhub 750/600 (Phase 2)
  • Page 527 Number Dis- play Function [2] Dial-In Settings [3] Memory [4] Closed Network RX [5] Forward TX Setting [6] Remote [7] Incom- plete TX Hold [8] PC-Fax RX Setting [9] TSI User Box Setting [6] PBX CN bizhub 750/600 (Phase 2) 13-19...
  • Page 528 [9] Multi Lines Telephone Dialing Meth- Setting Line Settings Number of RX Call Rings Line Monitor Sound Line Monitor Sound Vol- Function Set- PC-FAX TX ting Setting Number Dis- play Function Multi Lines Setting Sender Fax 13-20 bizhub 750/600 (Phase 2)
  • Page 529 [2] User Box Admin. Set- ting [3] Adminis- trator Securi- ty Level [4] Security Password Details Rules Prohibit Functions when Auth. Error Manual Des- tination Input Print Data Capture Secure Docu- ment Access Method Restrict Fax bizhub 750/600 (Phase 2) 13-21...
  • Page 530 All Data [4] HDD Lock Password [5] HDD For- matting [6] HDD En- Image Data cryption Set- Encryption ting Management Data Encryp- tion Key [7] Manage- [3] Network ment Func- Function Set- tino Setting ting 13-22 bizhub 750/600 (Phase 2)

  • Page 531: Selecting A Destination Register

    Touch Registration]. One-touch registration Parameter Description Address Book Register recipients for scanning. For details, refer to the Network Scanner Operations of the bizhub 750/600 User Group manual. Program Subject/Text (for E-mail) Note If user authentication has been set to "ON", [1 One-Touch Registration] does not appear when no user has logged on.

  • Page 532: Displaying The Destination Register Screen

    An item can also be selected by pressing the key in the keypad for the number beside the desired button. For "One-Touch Registration" press the [1] key in the keypad. The One-Touch Registration screen appears. 13-24 bizhub 750/600 (Phase 2)
  • Page 533 To quit specifying the Utility mode setting, touch [Exit] in the sub display area or press the [Utility/Counter] key. Otherwise, cancel the Utility mode by touching [Close] in each screen until the screen for the Copy, Scan or Box mode appears. bizhub 750/600 (Phase 2) 13-25...

  • Page 534: Specifying User Settings

    14w, 8-1/2 e 11w, 5-1/2 e 8-1/2v, F4, 8Kv, 16Kw / v. • Custom Size: Select when using cus- tom-sized paper. • Oversized Paper: Select when paper larger than a standard size is being used. 13-26 bizhub 750/600 (Phase 2)
  • Page 535 Tray 4/ Bypass tray/ LCU tion, single-sided or double-sided print- ing can be selected. Note To load paper of a different size into the tray 1 and 2 and the LCU, contact your technical representative. bizhub 750/600 (Phase 2) 13-27...
  • Page 536 [Power Save Setting] appears only if the "Administrator Security Level" parameter (displayed from the Administrator Setting screen) is set to "Level 1" or "Level 2". Detail For details on the "Administrator Security Level" parameter, refer to "Security setting" on page 13-56. 13-28 bizhub 750/600 (Phase 2)
  • Page 537 Print/Fax Output Setting Specify the settings for the print and fax functions. For details, refer to the IC-202 User manual and the bizhub 750/600 User manual [Facsimile Operations]. Output Tray Setting Specify the exit tray given priority with...

  • Page 538: Display Setting

    Rotate] in the Basic screen to select it. Scan Basic Screen Default Setting Parameter Description Default Tab Specify settings for scanning. For details, refer to the Network Scan- ner Operations of the bizhub 750/600 User manual. Program Default Address Book Default In- Address Type Symbol Display 13-30...

  • Page 539: Copy Screen

    Select the job list displayed as the default in the Job List screen. Current Print Jobs • Current Print Jobs: Print Job History The Current Jobs list appears on the Print tab. • Print Job History: The Job History list appears on the Print tab. bizhub 750/600 (Phase 2) 13-31...

  • Page 540: Initial Setting

    To change the default settings for Scan mode, press the [Scan] key, enter Utility mode, and then select a setting for this parameter. Detail For details on the default settings and the factory default settings, refer to "Automatically canceling the settings (Automatic panel reset)" on page 3-31. 13-32 bizhub 750/600 (Phase 2)

  • Page 541: Copier Setting

    (except when "Auto Paper Se- lect" is set). Auto Zoom (ADF) Select whether or not the "Auto Zoom" / OFF setting is selected when a paper tray is selected (except when "Auto Paper Se- lect" is set). bizhub 750/600 (Phase 2) 13-33...
  • Page 542 • Accept: Print data can be accepted and print- • Receive Only: Print data is printed after the copy op- eration is finished. • Do Not Accept: Print data is not received. 13-34 bizhub 750/600 (Phase 2)
  • Page 543 [Print Jobs During Copy Operation] appear only if the "Administrator Security Level" parameter (displayed from the Administrator Setting screen) is set to "Level 2". Detail For details on the "Administrator Security Level" parameter, refer to "Security setting" on page 13-56. bizhub 750/600 (Phase 2) 13-35...

  • Page 544: Scanner Setting

    Parameter Description Black Compression Specify settings for scanning. For details, refer to the Network Scan- Level ner Operations of the bizhub 750/600 User manual. PrintersSetting Parameter Description Basic Setting Specify settings for printing. For details, refer to the IC-202 User manual.

  • Page 545: Displaying The User Setting Screen

    An item can also be selected by pressing the key in the keypad for the number beside the desired button. For "2 User Setting", press the [2] key in the keypad. The User Setting screen appears. bizhub 750/600 (Phase 2) 13-37...
  • Page 546 To quit specifying the User mode setting, touch [Exit] in the sub display area or press the [Utility/Counter] key. Otherwise, cancel the User mode by touching [Close] in each screen until the screen for the Copy, Scan or Box mode appears. 13-38 bizhub 750/600 (Phase 2)

  • Page 547: Specifying Administrator Settings

    Sleep mode is can- celed, therefore taking more prepara- tion time than Low Power mode. Entering Power Save Specify settings for faxing. For details, refer to the Facsimile Opera- Mode (Fax) tions of the C450 User manual. bizhub 750/600 (Phase 2) 13-39...
  • Page 548 The "Exit Tray Setting" parameter is available only if optional finisher FS- 504/FS-505/FS-602 is installed. Date/Time Setting Description Settings (Default set- highlighted tings are Specify the date, time and time zone for the machine’s internal clock. Time Zone: -12:00 to 13:00 00:00 13-40 bizhub 750/600 (Phase 2)
  • Page 549 If the weekly timer has been set, leave the machine plugged into the electrical outlet even if the machine has been turned off. If the weekly timer is set, correctly set the date and time. bizhub 750/600 (Phase 2) 13-41...

  • Page 550: Restrict User Access

    Image with the "Store Overlay" function can be Overlay deleted or overwritten. Restrict Restrict Select whether to prevent multiple recip- / OFF Operation Fax Broad- ients from being specified for fax trans- Setting casting missions. 13-42 bizhub 750/600 (Phase 2)

  • Page 551: Expert Adjustment

    2nd-Side Size Adjust- The 2nd-side size can be adjusted for Tray 1 to 4, Bypass, LCU ment each tray. key: No Selection 0.1%/ -0.2%/ -0.3% bizhub 750/600 (Phase 2) 13-43...
  • Page 552 (FS-602) Cover Adjust the cover sheet tray size if the pa- Upper Tray / Lower Tray Sheet per cannot be detected correctly or if one Tray Size side of the post inserter is adjusted. (PI-501) 13-44 bizhub 750/600 (Phase 2)
  • Page 553 Job Settings List The machine settings can be printed. In ad- dition, single-sided or double-sided printing can be selected. Paper Size/Type Counter Store up to 9 combinations of paper sizes and paper types to be counted. bizhub 750/600 (Phase 2) 13-45...

  • Page 554: Reset Setting

    "OFF" is selected, the destination is cleared.) System Auto Reset for Select whether or not the automatic sys- / OFF Proof Copy tem reset operation is performed when the proof copy operation is stopped. 13-46 bizhub 750/600 (Phase 2)
  • Page 555 Specify settings for using boxes. For details, refer to the User manual ument [Box Operations]. LCD Backlight Setting highlighted Description Settings (Default settings are Adjust the brightness of the touch panel back- 1 to 16: light to one of 16 levels. bizhub 750/600 (Phase 2) 13-47...
  • Page 556 For details, contact your technical representative. Detail The "Original Size Detection Change 3" parameter specifies the detection of 8-1/2 e 14 and the Foolscap size. The size selected for the "Foolscap Size Setting" parameter can be changed. 13-48 bizhub 750/600 (Phase 2)

  • Page 557: Administrator/Machine Setting

    One-Touch Registration For details, refer to the Network Scanner Operations, Facsimile Op- List erations and Box Operations of the bizhub 750/600 User manual. Note [3 User Box] appears only if the hard disk drive is installed. bizhub 750/600 (Phase 2)

  • Page 558: User Authentication/Account Track

    Authentication" is set to "OFF" and "Account Track" is set to "OFF". When "# of Counters Assigned for Users" is set to "50", 950 accounts can be registered. If the hard disk drive is not installed, the number of counters assigned for users is 100. 13-50 bizhub 750/600 (Phase 2)
  • Page 559 Account Track Registra- Specify the password, printing permissions, and number of prints al- tion lowed for each account using this machine. Account Track Counter The copy, printer and scanner use for each account can be checked. bizhub 750/600 (Phase 2) 13-51...
  • Page 560 The user and account track counters can be printed. In addition, single-sided or double-sided printing can be selected. Detail [Counter List] does not appear if "Public User Access" is set to "OFF" and "Account Track" is set to "OFF". 13-52 bizhub 750/600 (Phase 2)

  • Page 561: Network Setting

    Utility Network setting Parameter Description Network setting Specify settings for using the network. For details, refer to the Net- work Scanner Operations of the bizhub 750/600 User manual. TCP/IP Setting NetWare Set http Server Setting FTP Setting SMB Setting AppleTalk Setting...
  • Page 562 Select whether the printed side is on the Outside / Inside lection inside or the outside when the page is folded in three. Note [Tri-Fold Printed Side Selection] is available only if optional finisher FS-602 is installed. 13-54 bizhub 750/600 (Phase 2)

  • Page 563: Printer Setting

    [7 Printer Setting] appears only if optional image controller IC-202 is installed. System connection Parameter Description IS OpenAPI Setting Specify settings for using the network. For details, refer to the Net- work Scanner Operations of the bizhub 750/600 User manual. bizhub 750/600 (Phase 2) 13-55...

  • Page 564: Security Setting

    The administrator password used to specify the Administrator mode 12345678 settings can be changed. User Box Admin. Setting Description Specify settings for using boxes. For details, refer to the Box Operations of the bizhub 750/600 User manual. Administrator Security Level Description Settings (Default set-...

  • Page 565: Security Details

    [Mode 2]: Type in the ID for the confiden- tial document, and then type in the pass- word after the document is selected. Restrict Fax TX Select whether or not fax transmissions are prohibited. bizhub 750/600 (Phase 2) 13-57...
  • Page 566 10 seconds to turn the machine on after turning it off. The machine may not operate correctly if it is turned on immediately after being turned off. Note [Print Data Capture] appears only if optional image controller IC-202 is installed. 13-58 bizhub 750/600 (Phase 2)

  • Page 567: Enhanced Security Mode

    HDD Setting Parameter Description Check HDD Capacity Specify settings for using boxes. For details, refer to the Box Oper- ations of the bizhub 750/600 User manual. Temporary Data Over- write Setting Overwrite All Data HDD Lock Password HDD Formatting Select this parameter to format the hard disk.

  • Page 568: Displaying The Administrator Setting Screen

    Touch [3 Administrator Setting]. – An item can also be selected by pressing the key in the keypad for the number beside the desired button. For "Administrator Setting", press the [3] key in the keypad. 13-60 bizhub 750/600 (Phase 2)
  • Page 569 The Administrator Setting screen appears. Note To quit specifying the Utility mode setting, touch [Exit] in the sub display area or press the [Utility/Counter] key. Otherwise, touch [Close] in each screen until the desired screen appears. bizhub 750/600 (Phase 2) 13-61...

  • Page 570: Adjusting The Printer

    The Expert Adjustment screen appears. Touch [3 Printer Adjustment]. The Printer Adjustment screen appears. Touch [1 Leading Edge Adjustment]. The Leading Edge Adjustment screen appears. Touch the button for the paper type to be set. 13-62 bizhub 750/600 (Phase 2)
  • Page 571 To scroll through the values quickly, touch [+] or [–] continuously. Repeat steps 7 through 11 until the desired print results are achieved. Touch [OK]. – To cancel changes to the settings, touch [Cancel]. The print position is adjusted. bizhub 750/600 (Phase 2) 13-63...

  • Page 572: Adjusting The Starting Print Position At The Left Edge

    The Expert Adjustment screen appears. Touch [3 Printer Adjustment]. The Printer Adjustment screen appears. Touch [2 Centering]. The Centering screen appears. Touch [Test Copy]. The Test Copy screen appears. Press the [Start] key. A test pattern is printed. 13-64 bizhub 750/600 (Phase 2)
  • Page 573 Each time [+] or [–] is touched, the value is increased or decreased by one increment. Repeat steps 6 through 10 until the desired print results are achieved. Touch [OK]. – To cancel changes to the settings, touch [Cancel]. The print position is adjusted. bizhub 750/600 (Phase 2) 13-65...

  • Page 574: Adjusting The Finisher

    Touch [1 System Setting]. The System Setting screen appears. Touch [7 Expert Adjustment]. The Expert Adjustment screen appears. Touch [5 Finisher Adjustment]. The Finisher Adjustment screen appears. Touch [1 Center Staple Position]. The Center Staple Position screen appears. 13-66 bizhub 750/600 (Phase 2)
  • Page 575 If the desire print results are not achieved, change the adjustment value. – If the staple position is too far to the right of the center of the paper, touch [+] (between 0.1 mm and 12.7 mm). bizhub 750/600 (Phase 2) 13-67...
  • Page 576 – To scroll through the values quickly, touch [+] or [–] continuously. Repeat steps 6 through 11 until the desired print results are achieved. Touch [OK]. – To cancel changes to the settings, touch [Cancel]. 13-68 bizhub 750/600 (Phase 2)

  • Page 577: Adjusting The Half-Fold Position

    Touch [2 Half-Fold Position]. The Half-Fold Position screen appears. Touch the button for the paper size to be set. Touch [Test Copy]. The Test Copy screen appears. Press the [Start] key. The test pattern is printed. bizhub 750/600 (Phase 2) 13-69...
  • Page 578 12.8 mm). – To scroll through the values quickly, touch [+] or [–] continuously. Repeat steps 6 through 11 until the desired print results achieved. Touch [OK]. – To cancel changes to the settings, touch [Cancel]. 13-70 bizhub 750/600 (Phase 2)

  • Page 579: Adjusting The Hole-Punching Positions (Punch Vertical Position)

    Touch [7 Expert Adjustment]. The Expert Adjustment screen appears. Touch [5 Finisher Adjustment]. The Finisher Adjustment screen appears. Touch [3 Punch Adjustment]. The Punch Adjustment screen appears. Touch [1 Punch Vertical Position]. The Punch Vertical Position screen appears. bizhub 750/600 (Phase 2) 13-71...
  • Page 580 If the desire print results are not achieved, change the adjustment value. – If the punch positions are too far above the center of the paper, touch [+] (between 0.1 mm and 5.0 mm). 13-72 bizhub 750/600 (Phase 2)
  • Page 581 Touch [OK]. – To cancel changes to the settings, touch [Cancel]. Note When PK-504/PK-505 and ZU-601/ZU-602 are installed, adjustments can be made using both the "Punch Adjustment" and "Z-Fold Position Adjustment" parameters. Contact your technical representative. bizhub 750/600 (Phase 2) 13-73...

  • Page 582: Adjusting The Hole-Punching Positions (Punch Horizontal Position)

    Touch [7 Expert Adjustment]. The Expert Adjustment screen appears. Touch [5 Finisher Adjustment]. The Finisher Adjustment screen appears. Touch [3 Punch Adjustment]. The Punch Adjustment screen appears. Touch [2 Punch Horizontal Position]. The Punch Horizontal Position screen appears. 13-74 bizhub 750/600 (Phase 2)
  • Page 583 If the desire print results are not achieved, change the adjustment value. – If the punch positions are too far on the right side of the paper, touch [+] (between 0.1 mm and 5.0 mm). bizhub 750/600 (Phase 2) 13-75...
  • Page 584 Touch [OK]. – To cancel changes to the settings, touch [Cancel]. Note When PK-504/PK-505 and ZU-601/ZU-602 are installed, adjustments can be made using both the "Punch Adjustment" and "Z-Fold Position Adjustment" parameters. Contact your technical representative. 13-76 bizhub 750/600 (Phase 2)

  • Page 585: Adjusting The Hole-Punching Positions (Punch Unit Vert. Position)

    The Expert Adjustment screen appears. Touch [5 Finisher Adjustment]. The Finisher Adjustment screen appears. Touch [3 Punch Adjustment]. The Punch Adjustment screen appears. Touch [3 Punch Unit Vert. Position]. The Punch Unit Vert. Position screen appears. bizhub 750/600 (Phase 2) 13-77...
  • Page 586 If the desire print results are not achieved, change the adjustment value. – If the punch positions are too far above the center of the paper, touch [+] (between 0.1 mm and 5.0 mm). 13-78 bizhub 750/600 (Phase 2)
  • Page 587 Touch [OK]. – To cancel changes to the settings, touch [Cancel]. Note When PK-504/PK-505 and ZU-601/ZU-602 are installed, adjustments can be made using both the "Punch Adjustment" and "Z-Fold Position Adjustment" parameters. Contact your technical representative. bizhub 750/600 (Phase 2) 13-79...

  • Page 588: Adjusting The Hole-Punching Positions (Punch Unit Hor. Position)

    The Expert Adjustment screen appears. Touch [5 Finisher Adjustment]. The Finisher Adjustment screen appears. Touch [3 Punch Adjustment]. The Punch Adjustment screen appears. Touch [4 Punch Unit Hor. Position]. The Punch Unit Hor. Position screen appears. 13-80 bizhub 750/600 (Phase 2)
  • Page 589 If the desire print results are not achieved, change the adjustment value. – If the punch positions are too far on the right side of the paper, touch [+] (between 0.1 mm and 5.0 mm). bizhub 750/600 (Phase 2) 13-81...
  • Page 590 Touch [OK]. – To cancel changes to the settings, touch [Cancel]. Note When PK-504/PK-505 and ZU-601/ZU-602 are installed, adjustments can be made using both the "Punch Adjustment" and "Z-Fold Position Adjustment" parameters. Contact your technical representative. 13-82 bizhub 750/600 (Phase 2)

  • Page 591: Adjusting The Hole-Punching Positions (Punch Resist Loop Size)

    The Expert Adjustment screen appears. Touch [5 Finisher Adjustment]. The Finisher Adjustment screen appears. Touch [3 Punch Adjustment]. The Punch Adjustment screen appears. Touch [5 Punch Resist Loop Size]. The Punch Regist Loop Size screen appears. bizhub 750/600 (Phase 2) 13-83...
  • Page 592 The sample copy is printed. Touch [Close]. The Punch Regist Loop Size screen appears again. Check the punch positions in the sample copy. If the desire print results are not achieved, change the adjustment value. 13-84 bizhub 750/600 (Phase 2)
  • Page 593 Touch [OK]. – To cancel changes to the settings, touch [Cancel]. Note When PK-504/PK-505 and ZU-601/ZU-602 are installed, adjustments can be made using both the "Punch Adjustment" and "Z-Fold Position Adjustment" parameters. Contact your technical representative. bizhub 750/600 (Phase 2) 13-85...

  • Page 594: Adjusting The Z-Fold Positions

    Touch [1st Z-Folded Position] or [2nd Z-Folded Position]. – Touch [1st Z-Folded Position]to adjust the first folding position. – Touch [2nd Z-Folded Position] to adjust the second folding position. The 1st Z-Folded Position or 2nd Z-Folded Position screen appears. 13-86 bizhub 750/600 (Phase 2)
  • Page 595 The sample copy is printed. Touch [Close]. The 1st Z-Folded Position or 2nd Z-Folded Position screen appears again. Check the folding positions in the sample copy. If the desire print results are not achieved, change the adjustment value. bizhub 750/600 (Phase 2) 13-87...
  • Page 596 1st Z-Folded 2nd Z-Folded Position Position – If the folding position is too far on the right side of the paper, touch [-] (between -0.1 mm and -12.8 mm). 1st Z-Folded 2nd Z-Folded Position Position 13-88 bizhub 750/600 (Phase 2)
  • Page 597 Touch [OK]. – To cancel changes to the settings, touch [Cancel]. Note When PK-504/PK-505 and ZU-601/ZU-602 are installed, adjustments can be made using both the "Punch Adjustment" and "Z-Fold Position Adjustment" parameters. Contact your technical representative. bizhub 750/600 (Phase 2) 13-89...

  • Page 598: Adjusting The Tri-Fold Positions

    Touch the button for the paper size to be set. Touch [Test Copy]. The Test Copy screen appears. Press the [Start] key. The sample copy is printed. Touch [Close]. The Tri-Fold Position screen appears again. 13-90 bizhub 750/600 (Phase 2)
  • Page 599 If the folding position is too far on the left side of the paper, touch [-] (between -0.1 mm and -12.8 mm). Repeat steps 6 through 11 until the desired print results are achieved. Touch [OK]. – To cancel changes to the settings, touch [Cancel]. bizhub 750/600 (Phase 2) 13-91...

  • Page 600: Adjusting The Pitch Of The Two Staples

    Touch [6 2 Position Staple]. The 2 Position Staple screen appears. Touch the button for setting to be specified. Touch [Test Copy]. The Test Copy screen appears. Press the [Start] key. The sample copy is printed. 13-92 bizhub 750/600 (Phase 2)
  • Page 601 Touch [+] and [-] to adjust the distance (between 128 and 160 mm) between the staples. Repeat steps 6 through 11 until the desired print results are achieved. Touch [OK]. – To cancel changes to the settings, touch [Cancel]. bizhub 750/600 (Phase 2) 13-93...

  • Page 602: Cover Sheet Tray Size

    Load A4 w -size paper into the selected paper tray. Press the [Start] key. – Adjust the post inserter tray. To adjust the other paper tray, repeat steps 6 through 8. Touch [Close]. – The Finisher Adjustment screen appears again. 13-94 bizhub 750/600 (Phase 2)

  • Page 603: Authentication Method

    Limits on the number of pages printed – Management of personal boxes by each owner – Delete and restrict jobs of other users - Account track – Counters for printing/scanning from each account – Limits on the number of pages printed bizhub 750/600 (Phase 2) 13-95...

  • Page 604: When User Authentication And Account Track Are Synchronized

    (each user) and on each department (each account). Note The account track and user authentication settings can be specified separately. Check the differences between these features, and then specify the appropriate settings. 13-96 bizhub 750/600 (Phase 2)

  • Page 605: When User Authentication And Account Track Are Used Separately

    This setup is used when the machine is used by multiple employees with each employee performing multiple duties, which are to be totaled separately. With this setup, totals can be maintained on each employee (each user) and on each duty of the employee (each account). bizhub 750/600 (Phase 2) 13-97...

  • Page 606: To Select An Authentication Method

    To cancel user authentication, touch [OFF]. – To use the user authentication function from an external server, touch [ON (External Server)], and then select the server type. – To use the user authentication function of this machine, touch [ON (MFP)]. 13-98 bizhub 750/600 (Phase 2)
  • Page 607 MFP: This machine can be used only with user authentication. – To require all information to be entered for user authentication and account tracking each time that the machine is used, touch [Do Not Synchronize]. bizhub 750/600 (Phase 2) 13-99...
  • Page 608 The authentication method is set. Reminder Do not differentiate between uppercase and lowercase letters in the user name for the external server. Since the bizhub 750/600 cannot differentiate between uppercase and lowercase letters, the operation may not be performed correctly.
  • Page 609 Administrator. For details, refer to the User manual for PageScope Data Administrator. If user authentication is changed from external server authentication to machine authentication, the data is not cleared. To cancel changes to the settings, touch [Cancel]. bizhub 750/600 (Phase 2) 13-101...

  • Page 610: User Authentication Setting

    "Public User Key" is set to "Do Not Display". Detail The factory default setting is "Do Not Display". 13-102 bizhub 750/600 (Phase 2)

  • Page 611: To Specify The Administrative Setting

    Touch [1 Administrative Setting]. Touch [User Name List], and then touch either [ON] or [OFF]. Whether a user name list button appears or not is set. Touch [Default Function Permission]. The Default Function Permission screen appears. bizhub 750/600 (Phase 2) 13-103...
  • Page 612 Touch [Public User Key], and then touch either [Display] or [Do Not Display]. This machine is set to display [Public User Access]. Note To limit machine use by authorized users, specify settings in the User Registration screen. 13-104 bizhub 750/600 (Phase 2)

  • Page 613: User Registration

    Touch [2 User Authentication Setting]. The User Authentication Setting screen appears. Touch [2 User Registration]. The User Registration screen appears. Touch the button for the desired user. The User Registration screen for the selected user appears. bizhub 750/600 (Phase 2) 13-105...
  • Page 614 % [User Password] is not available if "User Authentication" on the General Settings screen is set to "ON (External Server)". Type in the password (up to 64 characters), and then touch [OK]. A screen for retyping the password appears. 13-106 bizhub 750/600 (Phase 2)
  • Page 615 Before an account name can be selected, accounts must have been registered. For details on registering accounts, refer to "Account track registration" on page 13-113. Touch [Max. Allowance Set]. The Max. Allowance Set screen appears. Touch [Limit] or [No Limit]. bizhub 750/600 (Phase 2) 13-107...
  • Page 616 The functions are selected in the following order: Copy % Scan % Box. – If no operation is permitted, user authentication cannot be performed. 13-108 bizhub 750/600 (Phase 2)
  • Page 617 Utility Touch [OK]. The function permissions are set. Touch [OK]. – To erase the current user, touch [Cancel]. bizhub 750/600 (Phase 2) 13-109...

  • Page 618: User Counter

    - Total: Shows the total number of pages scanned/the total number of pages printed - Large Size: Shows the total number of large-sized pages scanned/the total number of pages printed Note Counting automatically continues with user counters for external server authentication. 13-110 bizhub 750/600 (Phase 2)

  • Page 619: To Check The Counter

    To clear the counters for all users, touch [Yes]. The maximum number allowed is not cleared. The User Counter screen for the selected user appears. Touch the button for the counter to be viewed, and then check the counter. bizhub 750/600 (Phase 2) 13-111...
  • Page 620 User Counter screen for the current user. A confirmation message appears, asking whether the counter should be cleared. To clear the counters for the current user, touch [Yes]. The maximum number allowed is not cleared. Touch [Close]. 13-112 bizhub 750/600 (Phase 2)

  • Page 621: Account Track Setting

    "Displaying the administrator setting screen" on page 13-60. Touch [4 User Authentication/Account Track]. The User Authentication/Account Track screen appears. Touch [3 Account Track Setting]. The Account Track Setting screen appears. Touch [1 Account Track Registration]. bizhub 750/600 (Phase 2) 13-113...
  • Page 622 Type in the account name (up to 8 characters), and then touch [OK]. – For details on typing in text, refer to "Entering text" on page 14-3. – If [Name] was displayed, type in the account name (up to 20 characters), and then touch [OK]. 13-114 bizhub 750/600 (Phase 2)
  • Page 623 A password that repeats the same character (for example, "11111111") A password containing less than 8 characters A screen for retyping the password appears. Retype the password specified in step 9, and then touch [OK]. The account password is set. bizhub 750/600 (Phase 2) 13-115...
  • Page 624 At this time, do not turn off the machine with the main power switch. Touch [OK]. The maximum number of prints allowed is set. Touch [OK]. – To cancel changes to the settings, touch [Cancel]. 13-116 bizhub 750/600 (Phase 2)

  • Page 625: Account Track Counter

    - Large Size: Shows the total number of printouts made on large-sized paper Scan - Total: Shows the total number of pages scanned/the total number of pages printed - Large Size: Shows the total number of large-sized pages scanned/the total number of pages printed bizhub 750/600 (Phase 2) 13-117...

  • Page 626: To Check The Counter

    Account Track Counter screen for the current account. A confirmation message appears, asking whether the counter should be cleared. To clear the counters for the current account, touch [Yes]. The maximum number allowed is not cleared. 13-118 bizhub 750/600 (Phase 2)
  • Page 627 Utility Touch [Close]. bizhub 750/600 (Phase 2) 13-119...

  • Page 628: 13.10 Password Rules

    Limitations on registering/changing characters 8 alphanumeric characters (case- • A password that consists of a repetition of the same sensitive) character cannot be registered. • The same password as one before being changed can- not be registered. 13-120 bizhub 750/600 (Phase 2)
  • Page 629 Use the user password/account password when user authentication/account track settings have been applied. For details on the "User Box Password" and "Password for the secure document", refer to the bizhub 750/600 User manual [Box Operations]. bizhub 750/600 (Phase 2) 13-121...

  • Page 630: 13.11 Enhanced Security Settings

    Certain conditions must be met in order for the enhanced security settings to be applied. For details, contact your technical representative. The settings that must be specified or are forcibly set when "Enhanced Security Mode" is set to "ON" cannot be changed. 13-122 bizhub 750/600 (Phase 2)
  • Page 631 "Password Only" is selected, the setting for "Prohibit Functions When Auth. Error" is not changed, even when "Enhanced Security Mode" is set to "ON". [SSL] appears when a certificate is issued from PageScope Web Connection. bizhub 750/600 (Phase 2) 13-123...
  • Page 632 For details on the password rules, refer to "Password rules" on page 13-120. For details on the changed network settings, refer to the User manual [Network Scanner Operations]. 13-124 bizhub 750/600 (Phase 2)
  • Page 633 For details on the limitations placed on the user for printing, refer to the User manual [Print Operations]. For details on canceling operation restrictions applied when authentication failed, refer to "Security setting" on page 13-56. bizhub 750/600 (Phase 2) 13-125...
  • Page 634 Utility 13-126 bizhub 750/600 (Phase 2)

  • Page 635: Appendix

    Appendix...

  • Page 637: Entering Text

    The keypad can also be used to type in numbers. Any of the following keyboards may appear. Example Password input screen Screen for entering the name of a custom paper size bizhub 750/600 (Phase 2) 14-3...
  • Page 638 Appendix Touching [Shift] switches the keyboard display between lowercase letters (numbers) and uppercase letters (symbols). 14-4 bizhub 750/600 (Phase 2)

  • Page 639: To Type Text

    To change a character in the entered text, touch [ Back] and [Fwd. to move the cursor to the character to be changed, touch [Delete], and then type in the desired letter or number. List of available characters Type Characters Alphanumeric characters / symbols bizhub 750/600 (Phase 2) 14-5...

  • Page 640: Function Combination Table

    Appendix 14.2 Function combination table 14-6 bizhub 750/600 (Phase 2)
  • Page 641 Appendix bizhub 750/600 (Phase 2) 14-7...
  • Page 642 Appendix 14-8 bizhub 750/600 (Phase 2)
  • Page 643 Appendix bizhub 750/600 (Phase 2) 14-9...
  • Page 644 Appendix 14-10 bizhub 750/600 (Phase 2)
  • Page 645 Appendix bizhub 750/600 (Phase 2) 14-11...
  • Page 646 Appendix 14-12 bizhub 750/600 (Phase 2)
  • Page 647 Appendix bizhub 750/600 (Phase 2) 14-13...
  • Page 648 • When the "Booklet" function is specified • When the "Image Repeat" function is specified The "Mixed Original" setting and "Group" setting can be combined; however, they cannot be combined if a Staple setting is also selected. 14-14 bizhub 750/600 (Phase 2)
  • Page 649 If paper is fed from the post inserter PI-501, the settings cannot be used together. If a document is being scanned, the setting specified first is given priority, and a warning message appears. When scanning of the document is finished, the settings can be used together. bizhub 750/600 (Phase 2) 14-15...
  • Page 650 Appendix 14-16 bizhub 750/600 (Phase 2)

  • Page 651: Index

    Index...
  • Page 653 Cover sheet tray size 14-5 Available characters 4-71 Crisscross sorting 12-14 Current jobs 3-20 Basic screen 8-14 8-33 Custom size settings 3-11 BM tray (Finisher) 8-17 Custom size settings store 9-39 Book copy 9-78 Booklet pagination bizhub 750/600 (Phase 2) 15-3...
  • Page 654 Key counter 3-11 Finisher FS-602 5-28 Key repeat start/interval time 4-68 Finishing settings 3-18 Keypad 13-69 Folding position adjustment Front doors (left and right) 14-6 Function combinations Large capacity unit LU-401/LU-402 Fusing unit 3-10 3-51 15-4 bizhub 750/600 (Phase 2)
  • Page 655 Power source 9-37 4-43 Negative/positive reverse Preset zoom ratios 11-8 Network connector Preventive maintenance time 13-53 13-62 Network setting Printer adjustment 4-99 13-36 13-55 Next job reservation Printer setting 9-88 12-21 Non-Image area erase Printing priority bizhub 750/600 (Phase 2) 15-5...
  • Page 656 Total counter 9-102 Set numbering 3-17 Touch panel 9-52 Set range 5-43 Touch panel adjustment 4-49 Set zoom ratios 3-44 Tray 1 3-16 7-11 Shift tray SF-601 3-44 Tray 2 4-54 Single-sided copies 3-46 Tray 3 15-6 bizhub 750/600 (Phase 2)
  • Page 657 Utility mode parameters 3-18 Utility/Counter key 9-107 Watermark 3-35 Weekly timer Working table Z folding unit ZU-601/ZU-602 3-15 7-10 Z-fold position adjustment 13-86 4-42 Zoom minimal setting 4-44 4-51 Zoom ratio setting 4-39 Zoom settings bizhub 750/600 (Phase 2) 15-7...
  • Page 658 Index 15-8 bizhub 750/600 (Phase 2)

This manual is also suitable for:

Bizhub 600

Table of Contents