Memory Switch Setting [13] - Oce 3275 User Manual

Key Operator Mode

Memory Switch Setting [13]

This function allows you to change the Memory Settings listed below. See pp. 14-42~14-
45 for details on Memory Settings.
SW No.
No. 01: Auto reset timer
No. 02: AUTO RESET key function
No. 03: RADF-Original effect
No. 04: Job memory auto recall (30)
No. 05: Finisher mode by Full-auto
No. 06: Initial by Key counter insert
No. 07: Erasure outside area of orig.
No. 08: RADF frame erasure selection
No. 09: Automatic tray switching
No. 10: Platen APS
No. 11: RADF APS
No. 12: Platen AMS
No. 13: RADF AMS
No. 14: Select tray when APS cancel
No. 15: Platen original size detect
No. 16: RADF original size detect
No. 17: Platen orig. size detect (SMALL)
No. 18: Rotation
No. 19: Rotation (180 angle)
No. 20: B6R size original type
No. 21: A3, B4, 11x17, 8.5x14, F4 orig. type
No. 22: Staple mode reset-function
No. 23: Job offset operating
No. 24: Continuation print
No. 25: SDF Auto start
No. 26: Key click sound
No. 27: 1 SHOT indication time
No. 28: Power save screen
No. 29: START key latch function
No. 30: STOP key function
No. 31: Auto select of Booklet copy
No. 32: E.C.M. password
No. 33: Arrow key change (Image Shift)
No. 34: Exit direction of 1 sheet
No. 35: An interruption suspended way
No. 36: E.C.M. password input timing
14-40 Key Operator Mode
Item
OFF/ 30 sec./ 60 sec./ 90 sec./ 120 sec./150 sec./
180 sec./ 210 sec./ 240 sec./ 270 sec./ 300 sec.
Full-Auto/ Initial Setting
RADF AUTO RESET key selected/ RADF selected
OFF/ ON
Face down (Sub tray)/ Non-sort/ Sort/ Staple sort/
Folding&Stapling/ Folding/ Face up (Sub tray)
OFF/ ON
Erased for except Platen (1:1)/ Area outside of
orig. erased/ Erased for APS/AMS only
None/ 1mm frame/ 2mm frame/ 3mm frame/
4mm frame/ 5mm frame
OFF/ ON
OFF/ ON
OFF/ ON
OFF/ ON
OFF/ ON
APS preferential tray/ Tray 1/ Tray 2/ Tray 3/
Tray 4/ Bypass tray
Only A series/ Full size/ AB series/ Inch series
Only A series/ Full size/ AB series/ Inch series
A5R/ B6R/ 5.5"x8.5"R
ON-APS/AMS only/ ON-APS/AMS/Reduce only/
ON-Always
ON-Always/ According to Rotation OFF tray
Landscape/ Portrait
Landscape/ Portrait
OFF/ ON
OFF/ ON
OFF/ ON
OFF/ ON-Memory mode only
OFF/ ON
3 seconds/ 5 seconds
Shut off mode/ Low power mode
OFF/ ON
JOB momentary stop/ JOB cancel
Automatic selection/ Non Automatic selection
Under 8 digits/ 8 digits
Decimal point off (1 STEP 1mm)/ Decimal point
on (1 STEP 0.1mm)
Face up/ Face down
Division of a number of copies/ During of a
number of copies
Auto reset timer/ Complete job
Setting (default is underlined)