Electrical Specifi Cations - Jandy AquaPure APURE700 Installation And Operation Manual

Flow/Temperature/Salinity Sensor
there is adequate water fl ow through the Cell. The salinity portion of the Flow/Temp/
Salinity Sensor detects the level of salt in the pool water. This salt level is displayed
in grams per liter (gpl) on the Liquid Crystal Display (LCD) whenever the salinity
button is pressed. This eliminates the need for manual pool water salinity testing.
Pool Temperature is now available on all models by pressing the
A Pool Pump Timer is not included as part of your AquaPure. It is recommended that
Pool Pump Timer
a timer or an AquaLink RS control system be used to save on energy and prolong the
service life of your pool pump and the AquaPure.
2.1 Electrical Specifi cations
2 pole 20 AMP device at the Electrical Panel.
Circuit Protection
Model APURE700
Input: 120 VAC, 50/60 Hz, 1.5 AMPS
240 VAC, 50/60 Hz, 0.75 AMPS
Output: 22-30 VDC @ 3 AMPS maximum
Chlorine: 0.625 lb. / 24 Hr. (283 gm / 24 Hr.)
External ORP/External Control Connector
Control: AquaLink
Factory wired for 240 VAC service. If available electrical service is 120 VAC, the power supply
wiring must be changed to operate on 120 VAC as shown in the wiring diagram below. (Figure 2.)
Stripe
Flow/Temp/Salinity
Sensor
Flow
Test Points
Sensor
A to K
Aux Board
Front PCB
Test Points
Reverse Side
Common
Figure 2. APURE700 and APURE1400 Wiring Diagram
The Flow/Temp/Salinity Sensor only allows the Cell to operate if
® RS485 Connector
Use Copper Conductors Only – Rated for 90°C Minimum
Circuit Breaker
Panel
240 VAC
50/60 Hz
3 wire
Test
Switches
R H S
ORP RED BLK YEL GRN
24 VAC AquaLink RS
Blue to Blue - 75 VAC (pin 1 to 8)
-L
Blk/Green to BLK/Green - 65 VAC
(pin 2 to 7)
-U
Test Points
L to U
From Front
PCN
Input:
Output:
Chlorine: 1.25 lb. / 24 Hr. (567 gm / 24 Hr.)
External
Control:
CAUTION
Pool Pump Timer
12
Factory Wired for
9
3
6
Line 1
Line 2
Ground
Pool Pump
Re-wired for
1 A
Test Points
1-8 A B
8 B
Green
DC Cord
22 - 30 VDC
Back
PCB
Black / White
Stripe
Temperature
Model APURE1400
120 VAC, 50/60 Hz, 2.5 AMPS
240 VAC, 50/60 Hz, 1.25 AMPS
22-30 VDC @ 6 AMPS maximum
ORP/External Control Connector
AquaLink ® RS485 Connector
Transformer
Wire Nut Connections
Load 1 to Blk
~
Load 2 to Blk/Yel
240 VAC
Blk/Red to Blk/Wht
Load 2
Load 1
Ground (Chassis)
To Earth
Bonding Point
Wire Nut Connections
~
120 VAC
Load 1 to Blk/Wht and Blk/Yel
Load 2 to Blk/Red and Blk
Load 1 (Hot)
Blk/Yel
Load 2 (Neutral)
Blk/Wht
Ground (Chassis)
To Earth
Blk/Red
Bonding Point
Page 7
button.
Blk/Yel
Blk/Red
Blk/Wht
Blk
Blk