Pausing Or Restarting; Changing Cycles, Options And Modifiers; Status Lights - Kenmore 110.4586 Owner's Manual & Installation Instructions

Powdered detergent: Put the separator in the back position,
behind the guides, as shown following. There will be a gap
between the bottom of the wash cycle detergent
compartment and the bottom of the separator.
A I [] powoE.
B ........................... __
Separator in back position, behind guides
A. Separator
B. Guide
LIQU
SC
NOTE: The separator will be in the powder (back) position when
shipped from the factory.
Chlorine bleach compartment
(Letter D in Dispenser Illustration)
Add no more than 1/3cup (80 mL) liquid chlorine bleach to this
compartment. The bleach will be automatically diluted and
dispensed at the best time during the first rinse after the wash
cycle. This compartment cannot dilute powdered bleach.
• Always measure liquid chlorine bleach. Use a measuring cup
with a pour spout; do not guess.
• Do not fill beyond the "MAX" level.
NOTE: Overfilling could cause severe garment damage.
Fabric Softener compartment
(Letter E in Dispenser Illustration)
Add 1Acup (60 mL) liquid fabric softener to this compartment.
Fabric softener will be automatically dispensed in the final rinse.
• Do not fill beyond the "MAX" level.
1. To pause the washer at any time, select PAUSE/CANCEL
2. To continue the cycle, select and hold START (for
approximately 1 second).
Not all Options and Modifiers are available with all Cycles.
Cycles, Options and Modifiers can be changed anytime before
START is selected,
Options and Modifiers can be changed anytime after START is
selected and before the start of the selected Option or Modifier,
To cancel a cycle and select a new cycle
1. Select PAUSE/CANCEL twice.
2. Select desired cycle.
3. Select the desired OPTIONS and MODIFIERS.
4. Select and hold START (for approximately 1 second) to restart
the washer at the beginning of the new cycle.
To cancel a cycle
1. Select PAUSE/CANCEL twice.
2. The washer powers down, the door unlocks, and clothes can
be removed.
NOTE: If the water level or the temperature is too high, the
washer will drain automatically before the door unlocks.
To change Options and Modifiers after the cycle has started
1. Select PAUSE/CANCEL once.
2. Select the desired OPTIONS or MODIFIERS.
3. Select and hold START (for approximately 1 second) to
continue the cycle.
To drain the washer manually
1. Select PAUSE/CANCEL once.
2. Select DRAIN & SPIN.
3. Select and hold START (for approximately 1 second) to begin
the drain.
4. When the spin is complete, the door unlocks. Items can be
removed from the washer.
These lights show which portion of the cycle the washer is
operating. They also indicate when you can add an additional
item to the wash cycle and when the controls are locked.
STATUS
ADD A GARMENT0
PREWASIQ
WASH®
RINS£0
SPIN®
CLOTHES CLEAN0
CONTROL LOCKED0
DOORLOCKrD•
Adding items
You can add items to the washer after the cycle has started for
Normal/Casual, Heavy Duty or Whitest Whites if the ADD A
GARMENT status light is glowing.
To add items
1. Select PAUSE/CANCEL. The washer door unlocks, and items
can be added.
2. To continue the cycle, close the door and select and hold
START (for approximately 1 second).
3. To unlock the door after the Add A Garment period, press
Pause/Canel twice. This will cancel the Wash Cycle.
Clothes Clean
The Clothes Clean light stays on after the cycle is completed,
until the door is opened. The washer will then power down.
Locking controls
The Control Lock avoids unintended use of the washer. You can
also use the control lock feature to avoid unintended cycle or
option changes during a cycle. When CONTROL LOCKED is lit,
all buttons are disabled except for Pause/Cancel and Start. You
can lock the controls while the washer is operating.
14