AMX Epica DGX 16 Instruction Manual
  1. Manuals
  2. Brands
  3. AMX Manuals
  4. Matrix Switcher
  5. Epica DGX 16
  6. Instruction manual

AMX Epica DGX 16 Instruction Manual

Distribution matrix
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Instruction Manual
Epica DGX 16
Epica DGX 32
Distribution Matrix
A u t o P a t c h M a t r i x S w i t c h e r s
R E V B 1 : 1 / 2 5 / 2 0 1 1

Advertisement

Table of Contents
loading

Related Manuals for AMX Epica DGX 16

Summary of Contents for AMX Epica DGX 16

  • Page 1 Instruction Manual Epica DGX 16 Epica DGX 32 Distribution Matrix A u t o P a t c h M a t r i x S w i t c h e r s R E V B 1 : 1 / 2 5 / 2 0 1 1...

  • Page 2: Amx Limited Warranty And Disclaimer

    Partner which include AMX Dealers, Distributors, VIP’s or other AMX authorized entity. AMX warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase, with the following exceptions: •...

  • Page 3: Table Of Contents

    System Setup with DGX Modules..................49 Safety Recommendations for Laser Products ................ 50 Attaching Cables ........................50 Epica DGX DVI Boards ..................53 Specifications Epica DGX DVI....................54 Attaching Cables ........................55 Epica DGX 16 and Epica DGX 32 Instruction Manual...
  • Page 4 Editing the Clock Manager Settings ..................89 DoD Security Mode ....................... 91 ICSP Support ......................... 93 NXB-AP-1000 Interface – Controlling an Epica DGX 16 or 32 ......95 XBar Controller Overview...................... 95 Executing and Disconnecting Switches with the XBar ............95 NXB-AP-1000 Interface –...
  • Page 5 Installing the EDID Programmer ..................110 Reading and Saving EDID Data from a Destination Device ..........111 Writing EDID Data to Epica DGX 16 or 32 DVI Input Connector......... 112 Appendix B – Managing Configuration Files ...........115 Overview ..........................116 Installing and Launching XNConnect ...................
  • Page 6 Contents Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 7: Esd Warning

    Grounding straps, conductive smocks, and conductive work mats are specifically designed for this purpose. Anyone performing field maintenance on AMX AutoPatch equipment should use an appropriate ESD field service kit complete with at least a dissipative work mat with a ground cord and a UL listed adjustable wrist strap with another ground cord.

  • Page 8: Important Safety Information And Instructions

    There are no user serviceable parts inside an AMX AutoPatch product; service should only be done by qualified personnel. If you see smoke or smell a strange odor coming from your AMX AutoPatch product, turn it off immediately and call technical support.

  • Page 9: Information Et Directives De Sécurité Importantes

    Placez uniquement des fusibles de calibre exact dans les boîtiers. Veillez à ce que la prise de courant soit proche de l’appareil et facile d’accès. Veillez à ce que votre appareil AMX AutoPatch soit installé sur une surface stable ou qu’il y soit fermement maintenu.

  • Page 10: Notices

    No patent liability is assumed with respect to the use of information contained herein. While every precaution has been taken in the preparation of this publication, AMX assumes no responsibility for error or omissions. No liability is assumed for damages resulting from the use of the information contained herein.
  • Page 11 Caution: The icon to the left indicates text that cautions readers against actions that could cause potential injury to the product or the possibility of serious inconvenience. Epica DGX 16 and Epica DGX 32 Instruction Manual...
  • Page 12 Notices Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 13: Overview And General Specifications

    The information in this manual applies to the following Epica DGX 16 and 32 enclosures and Epica DGX 16 and 32 pre-engineered systems. It also applies to Epica DGX Input and Output Boards, which can be ordered separately. These boards are compatible in both the Epica DGX 16 and 32.

  • Page 14: Product Notes

    For model numbers of the compatible modules, see page 48. For system setup information, see page 49. Product Notes The Epica DGX 16 and 32 are available in both pre-engineered (DVI only) and custom systems in a variety of input to output configuration sizes and can contain an assortment of input and output boards in a single enclosure.
  • Page 15 Virtual matrices (levels) / groupings; ships with free matrix switcher configuration software. RJ-45 Ethernet (Enc Link) ports support linking to AMX AutoPatch matrix switchers. Local presets allow quick recall of a pre-programmed set of switches with a single command;...

  • Page 16: Front View

    Overview and General Specifications Front View The enclosure, which is the structural basis of the Epica DGX 16 and 32 Distribution Matrices, can be controlled using the standard front control panel, control software, or an external controller (for additional information on control options, see page 15 and for control panel operation, see page 57). The Power LED indicates the status of the power supplies.
  • Page 17 Each CPU includes two main LED indicators: System Status indicator (between the Enc Link ports and the Control port) for system status – NXB-AP-1000 LED Indicator (left of TCP/IP port) – indicates an active connection Epica DGX 16 and Epica DGX 32 Instruction Manual...
  • Page 18 FIG. 6 DGX DVI and DGX SC Optical Input and Output Boards Epica DGX 16 enclosures have 8 horizontal board slots (4 slots each for input and output boards with four connectors each), allowing for a maximum configuration of 16x16.
  • Page 19 (for attaching destinations) are on the right. Input and output channel numbers correspond to the connectors and are located as follows: Epica DGX 16 – on the vertical numbering plate (metal strip) between the input and output connectors.

  • Page 20: Epica Dgx 16 General Specifications

    Weight Approximately 34 lb. (15.4 kg) per loaded enclosure Shipping Weight Approximately 40 lb. (18.1 kg) per loaded enclosure Compatible Fiber Modules AMX AutoPatch DGX Fiber TX and DGX Fiber RX modules Epica DGX 32 General Specifications Specifications Parameter Value...

  • Page 21: Configuration Information And Control Options

    The Control Panel (see page 57) is standard on all Epica DGX 16 and 32 enclosures. Note: When using the control panel on an Epica DGX 16 or 32 to control a larger matrix switcher in a linked system, the number of inputs and outputs that can be controlled on the larger matrix switcher cannot be greater than the number of ones available on the Epica DGX 16 or 32.

  • Page 22: Epica Dgx

    Protocol on the AMX AutoPatch CD or at www.amx.com. Third-Party Controllers A third-party controller can also be attached to an Epica DGX 16 or 32 enclosure via the RS-232 serial port. If using a third-party controller, see the controller documentation for operating instructions.

  • Page 23: Installation And Setup

    FIG. 8 Caution label for Class 3R laser products Important: No user serviceable parts are included inside an AMX AutoPatch product; service should only be done by qualified personnel. Caution: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

  • Page 24: Site Recommendations

    These recommendations address potential hazards that are common to all installations: Elevated Operating Temperature The maximum rated ambient temperature for Epica DGX 16 and 32 enclosures is 113° F (45° C). All equipment should be installed in an environment compatible with the manufacturer’s maximum rated ambient temperature.

  • Page 25: Unpacking

    After powering up the enclosure, apply power to the source and destination devices. Unpacking The Epica DGX 16 and 32 are shipped with one enclosure per shipping box. The invoice is sent separately; a packing slip is attached to the outside of each box. Each box contains the following items:...

  • Page 26: System Setup Options

    Epica DGX 16, 32, and 144 enclosures is supported. Contact your AMX representative for these and other system design possibilities. Rack Installation and System Setup Epica DGX 16 and 32 enclosures can be mounted in a standard EIA 19 in. (48.26 cm) rack. Required Items for Rack Installation: Enclosure Standard EIA 19 in.

  • Page 27: Safety Recommendations For Laser Products

    Installation and Setup Safety Recommendations for Laser Products Important: No user serviceable parts are included inside an AMX AutoPatch product; service should only be done by qualified personnel. Caution - Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
  • Page 28 10. If applicable – Use the EDID Programmer.* * EDID Programmer software can be used for re-programming the DGX DVI Input Boards if necessary (see page 109). This software is located on the AMX AutoPatch CD (also available at www.amx.com). Additional Setup Additional setup tasks may include the following:.
  • Page 29 Installation and Setup Attaching Cable Management Bars AMX AutoPatch cable management bars are provided for DGX SC Optical Input and Output Boards. Caution: Do not severely bend or kink the SC fiber cable. Irreversible damage can occur. Refer to the physical limitations (bend radius) specified for the cable by the manufacturer. The bend radius for AMX SC terminated fiber cables is 2 inches (5 cm).

  • Page 30: Linking Enclosures

    Installation and Setup Linking Enclosures Epica DGX 16 and 32 enclosures can link to each other or to most other types of AMX AutoPatch Distribution Matrices (see the tables below). Important: The shipping boxes each have a bright yellow/green sticker that states that the unit (enclosure) is part of a multiple-enclosure system and must be installed with the same serial numbers.
  • Page 31 Linking Epica DGX 16 or 32 to Enclosure with RJ-45 Link Connector An Epica DGX 16 or 32 can be directly linked to another Epica DGX 16 or 32, an Epica DGX 144, Epica DG, Optima, Optima SD, or to a Precis SD enclosure via their 10Base-T Ethernet ports using an RJ-45 cable.
  • Page 32 Linking Epica DGX 16 or 32 to Enclosure with BNC Link (Also BNC Daisy Chain) An Epica DGX 16 or 32 enclosure can be linked to an enclosure with an Ethernet 10Base-2 (BNC) connector (Modula, Modula CatPro, Epica-128, or Epica-256) by using a Media Converter, RJ-45 cable, and RG-58 coax cable.
  • Page 33 Multi-Port Switch (or hub) for linking enclosures, contact your network administrator. To link an Epica DGX 16 or 32 enclosure to a Multi-Port Switch: Insert one end of the RJ-45 cable into an Enc Link (RJ-45) Ethernet port on the Epica DGX 16 or 32 enclosure.
  • Page 34 * Applies to Modula, Modula CatPro, Epica-128, and Epica-256 enclosures. ** The total length of all RG-58 coax cables between the Media Converter and the last enclosure in the daisy chain cannot exceed 10 ft. (3.05 m). Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 35: Attaching External Controllers

    APControl 3.0 APControl 3.0 software (for control and scheduling) runs on a PC connected to an Epica DGX 16 or 32 via the serial port (DB-9) or the USB (mini-B) port and is available on the AMX AutoPatch CD.
  • Page 36 Plug the other end of the serial cable into the serial port on the serial controller. If not already on, apply power first to the Epica DGX 16 or 32 enclosure and then to the source and destination devices (see “Applying Power and Startup” on page 36).
  • Page 37 Epica DGX 16 and 32 Distribution Matrices are provided in the table above. Epica DGX 16 and 32 enclosures support baud rates of 9600 (default), 19200, 38400, and 57600. The settings on the PC serial communication software and the enclosure must correspond to each other. If a change is required to make them match, changing the PC’s settings is preferable.
  • Page 38 Connecting Serial Controller to USB Port Controlling an Epica DGX 16 or 32 using a USB connection requires the creation of a virtual Com port. Once created, the virtual Com port is used as if it were a standard serial connection and can connect to a ®...
  • Page 39 You must identify the virtual Com port assigned to the USB connector to enable communication between the control PC and an Epica DGX 16 or 32. The enclosure must be connected to the PC via the USB port and powered up before you start the following procedure, so the PC can display the port number.
  • Page 40 Stop Bits Flow Control None XBar (NXB-AP-1000 interface) – See page 95. Execute a test switch to make sure the Epica DGX 16 or 32 is working properly (see page 40). Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 41: Attaching Input And Output Cables

    (for attaching destinations) are on the right. Epica DGX 16 – Enclosures have 8 horizontal board slots (4 slots each for the input and the output boards, with 4 connectors per board), allowing for a maximum configuration of 16x16 (FIG. 20).

  • Page 42: Applying Power And Startup

    When attaching input and output signal cables in a multiple-enclosure system, check the system and enclosure numbers are on the rear of the Epica DGX 16 or 32 (if not on the rear, the numbers are on the side). The system was programmed at the factory to operate only as a specifically configured system.
  • Page 43 Execute a test switch (see page 40). (For startup information on specific types of control, see page 38 before executing a test switch.) 10. Attach the remaining sources and destinations and apply power to them. Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 44: Serial Control Device Startup

    100 Mbps (on) or 10 Mbps (off) * IOS (Initial Operating System) is the base layer operating system on AMX AutoPatch equipment. IOS performs functions such as hosting higher level run-time software applications. When unexpected critical errors are encountered within such hosted applications, system control of the equipment may be passed to the IOS layer preventing normal system operation until the error is manually cleared.

  • Page 45: Redundant Power Supply (Rps)

    Power Supply Troubleshooting If a power supply’s AC and DC power indicator LEDs are not illuminated: Check to be sure the power cord is completely plugged into the Epica DGX 16 or 32 and to the power source. If the AC and DC LEDs remain unilluminated, contact technical support (see page 42).

  • Page 46: Executing A Test Switch

    Directions for establishing an NXB-AP-1000 connection for control via the TCP/IP port start on page 42. AMX Controller For executing and disconnecting switches using an AMX Controller, see the instruction manual for the specific device. APControl 3.0 Directions for executing and disconnecting switches using APControl 3.0 are found in its Help file.
  • Page 47 For a complete list of BCS commands and responses, see the Instruction Manual – BCS Basic Control Structure Protocol on the AMX AutoPatch CD or at www.amx.com. Test Switch Troubleshooting If the test switch did not execute correctly: Check the power indicator on the front of the enclosure.

  • Page 48: Technical Support

    The NXB-AP-1000 delivers HTML pages for setting up the system and a Java control applet, which allows for remote control of an Epica DGX 16 or 32 using PC-based Internet browsing software. The enclosure is connected via an RJ-45 link cable to a LAN. The basic directions for the LAN connection follow.
  • Page 49 Cable Requirements LAN Connection – an RJ-45 link cable (either crossover or straight-through) is required to connect an Epica DGX 16 or 32 enclosure to a LAN. TCP/IP Port and Indicator LEDs The TCP/IP port, which provides the NXB-AP-1000 connection, is located on the rear of the enclosure on the right-hand side of the CPU (FIG.
  • Page 50 Accessing Zero-Config Information in the NetLinx Studio WebConsole To determine the DHCP IP address that the network assigned to the Epica DGX 16 or 32 in Step 3 of the previous instructions, you can access the unit via NetLinx Studio.
  • Page 51 Click the plus symbol (+) to the left of the “NIB IP-Bridge Interface” (the NXB-AP-1000 interface for the Epica DGX 16 or 32) in the Zero-Config list to expand its information. The NXB-AP-1000 interface’s current IP Address is listed below its system name of “NIB IP-Bridge Interface.”...
  • Page 52 All power, signal, and link connections on all of the equipment. LED indicators for the TCP/IP (RJ-45) connector on the rear of the Epica DGX 16 or 32. If the LED indicators are not illuminated, check the cable type to make sure it meets cable requirements (see page 43).

  • Page 53: Epica Dgx Sc Optical Boards

    Epica DGX SC Optical Boards, shown in an Epica DGX 32 Epica DGX 16 Epica DGX 16 enclosures are built to hold up to eight DGX SC Optical Boards with four inputs or outputs per board. Each enclosure holds a maximum of four input and four output boards, accommodating connector configurations up to a maximum of 16x16, as well as subsets (for example, 16x8 or 4x12).

  • Page 54: Specifications Epica Dgx Sc Optical Boards

    Note: Either Transmitter (TX) module can be used in conjunction with either Receiver (RX) module. Epica DGX SC Optical Specifications Parameter Value Compatible AMX AutoPatch Fiber Products DGX HD-15 TX and RX, DGX DVI TX and RX, other AMX AutoPatch DGX SC Fiber signal management products Signal Types over Fiber...

  • Page 55: System Setup With Dgx Modules

    Epica DGX SC Optical Boards System Setup with DGX Modules DGX SC Optical Input and Output Boards are used in conjunction with AMX AutoPatch DGX Fiber TX and RX modules. Compatible DGX Fiber modules are listed on page 48. System setup options are listed in a table on page 20.

  • Page 56: Safety Recommendations For Laser Products

    Attaching Cables Instructions for attaching AMX AutoPatch cable management bars are on page 23. These bars are recommended and provided with each DGX SC Optical Board. Caution: Do not severely bend or kink the SC fiber cable. Irreversible damage can occur. Refer to the physical limitations (bend radius) specified for the cable.
  • Page 57 Fasten cables onto input and output connectors (shown with cable management bar) Tie the SC fiber cable to the cable management bar far enough below the connector to allow for the manufacturer’s recommended bend radius. The bend radius for AMX SC terminated fiber cables is 2 inches (5 cm).
  • Page 58 Epica DGX SC Optical Boards Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 59: Epica Dgx Dvi Boards

    Epica DGX DVI Input and Output Boards Epica DGX 16 Epica DGX 16 enclosures are built to hold up to eight DGX DVI Boards with four inputs or outputs per board. Each enclosure holds a maximum of four input and four output boards, accommodating connector configurations up to a maximum of 16x16, as well as subsets (for example, 16x8 or 4x12).

  • Page 60: Specifications Epica Dgx Dvi

    60 Hz, 70 Hz, 75 Hz, 87 Hz 1280x1024 75 Hz ** Some monitors may not support the maximum refresh rate. AMX reserves the right to modify its products and their specifications without notice. Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 61: Attaching Cables

    23. CLK+ 8. No connect 16. Hot-Detect 24. CLK- * DVI output pin 14 (+5 VDC out) supplies 1 A shared total available for all four outputs. FIG. 35 DVI-I connector pinout Epica DGX 16 and Epica DGX 32 Instruction Manual...
  • Page 62 Epica DGX DVI Boards Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 63: Control Panel Operation

    Control Panel Operation Overview The Epica DGX 16 and 32 Control Panels (standard on all enclosures) are used for controlling system switches and system attributes. Both control panels function the same, but have input and output key support respective to their size.
  • Page 64 (inputs not available) Blue keys White keys Blue keys (outputs available) (outputs available) (outputs selected) FIG. 37 Example of key states during Change Mode (Control Panel on an Epica DGX 32) Epica DGX 16 and Epica DGX 32 Instruction Manual...
  • Page 65 Locking the panel limits access which can prevent accidental switches (see page 72). Adjust Audio This menu item will not display unless the Epica DGX 16 or 32 is linked to an enclosure that supports audio functions. Selecting Adjust Audio accesses the Adjust Audio submenu. From this menu, you can place the panel in Output Volume Mode, Mute/Unmute Mode, or Input Gain Mode (see page 68).
  • Page 66 Take Key. Labeling Input and Output Keys Each Epica DGX 16 and 32 system ships with a kit for custom labeling. Additional kits may be ordered separately. The Control Panel Label Kit (KA1056-01) includes: Perforated card stock sheets –...

  • Page 67: Executing Switches

    VM as the video (the audio and video cannot be switched independently). Note: When using the control panel on an Epica DGX 16 or 32 to control a larger matrix switcher in a linked system, the number of inputs and outputs that can be controlled on the larger matrix switcher cannot be greater than the number of ones available on the Epica DGX 16 or 32.

  • Page 68: Changing The Virtual Matrix

    VM 1 = “Video.” The system also supports any custom virtual matrices created in XNConnect; 2 digits are the maximum allowed (0 through 99). VM 0 is the factory default, and for the Epica DGX 16 and 32, VM 0 normally routes the same as VM 1. If you create a custom configuration, you will need to change the virtual matrix on the Control Panel to execute switches (or other operations) using the custom virtual matrix.

  • Page 69: Disconnecting Switches

    The example below disconnects Inputs 1 and 3 and all outputs connected to them as well as Output 9. To disconnect inputs and outputs: Press the Function Key. The Function menu appears. Locate Disconnect by scrolling with the Control Dial. Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 70: Verifying Signal Status

    Verifying Signal Status The status of inputs or outputs can be checked using the Epica DGX 16 and 32 Control Panel. Signal status can be verified to confirm that a switch has executed properly or to confirm correct routing to multiple outputs (destinations).

  • Page 71: Defining And Executing Global Presets

    That system state can be restored at any time by selecting the assigned global preset number. Global presets can be defined or recalled using either the Control Panel or BCS commands interchangeably. Control Panel on the Epica DGX 16 and 32 supports up to 64 global presets. Defining Global Presets A global preset is a snapshot of an entire system’s state which enables that system state to be recalled at...
  • Page 72 Global Preset 3 is executed. The system returns to the Global Preset submenu. Press the Function Key to return to the Function menu. Note: Status is not invalidated by global presets. Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 73: Executing Local Presets

    Local presets are not programmed (defined) at the factory. To program them, use XNConnect configuration software (see page 122) or contact your AMX representative (for contact information, see page 42). Once the local presets have been defined as part of the configuration file, the new file must be loaded to the system’s CPU (see page 124) and reloaded to the Control Panel (see page 75).

  • Page 74: Adjusting Audio

    Some audio boards in AMX AutoPatch Distribution Matrices offer optional volume control and digital input gain adjustment features. If your Epica DGX 16 or 32 system is linked to an enclosure that contains these boards, output volume or digital input gain can be adjusted using either the Control Panel or BCS commands sent through a serial controller.
  • Page 75 Note: If the selected output is muted, “Muted” displays as the current setting. Turning the Control Dial will un-mute a muted output and adjust the Volume. To reapply mute, see the next page). FIG. 39 Example of muted output in Output Volume Mode Epica DGX 16 and Epica DGX 32 Instruction Manual...
  • Page 76 Adjusting Digital Input Gain If an Epica DGX 16 or 32 is linked to an enclosure that supports input gain control, adjustments (within the gain range for the specific audio input board) can be made at any time during normal operation.
  • Page 77 If adjusting input gain for a single input – Repeat Steps 7 and 8 for the desired input. 10. Press the Cancel Key to return to the Adjust Audio submenu. Press the Function Key to return to the Function menu. Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 78: Locking And Unlocking

    Control Panel Operation Locking and Unlocking Locking the Epica DGX 16 or 32 Control Panel prohibits access to the system and can prevent accidental switching. While the panel is locked, BCS commands still work; however, they cannot be used to unlock the panel.

  • Page 79: Setup Options

    – software version of the initial operating system (IOS) for the Control Panel XNet ID – Control Panel’s XNNet device number Use the following steps to check the software version information for the Epica DGX 16 or 32 Control Panel. To check the software version information: Press the Function Key.
  • Page 80 Or press the Function Key to return to the Function menu. Default Virtual Matrix The factory default virtual matrix for the Epica DGX 16 and 32 is VM 0. You have the option of changing the factory default virtual matrix for your system. When you choose a new default virtual matrix, the system will revert to that virtual matrix each time the system is powered up even if you changed the virtual matrix using the V.Matrix list during normal operation.
  • Page 81 Press the Select Key. The configuration file reloads to the Control Panel and the display returns to the top of the Setup Options submenu. Press the Function Key to return to the Function menu. Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 82: Setting The Password

    Setting the Password The Epica DGX 16 and 32 Control Panel’s default password is “1 2 3 4 5” entered using the first five input keys. A new password can be set using any combination of five of the Input Keys 1 through 8 when the LCD displays “Enter New PWD”...

  • Page 83: System Error Codes And Troubleshooting

    This section provides an overview of the most common error codes that may appear on an Epica DGX 16 or 32 Control Panel. The table on the next page lists the error code, the name of the code, the meaning of the code, and some basic troubleshooting strategies (additional error code troubleshooting strategies are included on page 78).
  • Page 84 In other cases, the command has specified a value that is not valid (e.g., a global preset number that does not correspond to a defined global preset). If the error code persists after correcting and resending the command, contact technical support (see page 42). Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 85: Nxb-Ap-1000 Interface - Initial Setup By Network Admin

    When the NXB-AP-1000 interface is accessed, the NXB-AP-1000 delivers HTML pages for setting up the system and a Java control applet, which allows for remote control of an AMX AutoPatch Routing System using PC-based Internet browsing software. The interface can also function as a Tunneling Access Point (TAP).

  • Page 86: Determining Ip Address For Nxb-Ap-1000 Interface

    Accessing Zero-Config Information in the NetLinx Studio WebConsole To determine the DHCP IP address that the network assigned to the Epica DGX 16 or 32 when the LAN connection was established, you can access the unit via the Zero-Config feature in NetLinx Studio.

  • Page 87: Opening The Nxb-Ap-1000 Interface

    NXB-AP-1000 Home page shows system configuration information (Epica DGX 32 example) Complete any necessary configuration of the NXB-AP-1000 interface. Instructions are included in this chapter. If the Home page does not open, see the “NXB-AP-1000 Troubleshooting” section on page 46. Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 88: Navigating The Nxb-Ap-1000 Interface

    Important: Any time you click “Reboot” from any page in the NXB-AP-1000 interface, the server reboots. The reboot updates information between the Epica DGX 16 or 32 and the server. (The Epica DGX 16 or 32 system itself does not reboot).

  • Page 89: Setting A Static Ip Address

    PC, including those with access to a NetLinx Master. The instructions on the next page assume all of the items below have been completed: An active connection between the TCP/IP port on the Epica DGX 16 or 32 and the LAN has been established (see page 42).
  • Page 90 Master Username and Master Password. Click Accept to save the changes. Click Reboot to reboot the Epica DGX 16 or 32 connection. Once rebooted, the matrix switcher is in communication with the NetLinx Master, as indicated by steady a blink on the enclosure’s NXB-AP-1000 Status LED to the left of the TCP/IP port.

  • Page 91: Handling Security Issues

    When Telnet Security is enabled, a username and password are required to establish a Telnet or SSH connection. Admin Security When Admin Security is enabled, a username and password are required to modify any system configuration item. Epica DGX 16 and Epica DGX 32 Instruction Manual...
  • Page 92 Click the Login link in the upper-right corner of any page. The Login dialog box opens. Enter the login information specified during security setup (see above). Default Username = administrator Default Password = password Click the Login button. Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 93: Executing A Test Switch With The Xbar Controller

    Note: For complete information on the XBar Controller, see page 95. The test switch below routes Input 1 (source channel 1) to Output 1 (destination channel 1) on VM 0 (the default virtual matrix for the Epica DGX 16 and 32). To execute a test switch with the XBar: Install the Java Plug-in* if necessary.

  • Page 94: Customizing The Xbar Controller

    If the XBar is open, close before proceeding. From the IP Control drop down menu, select Preferences. In the Initial VM Displayed field, enter the virtual matrix number (the Epica DGX 16 and 32 normally have two virtual matrices: VM 0 = all; VM 1 = video).

  • Page 95: Executing And Disconnecting Switches

    Executing and Disconnecting Switches The NXB-AP-1000 interface provides the XBar Controller for executing and disconnecting switches on an AMX AutoPatch Routing System. For complete information, see the “NXB-AP-1000 Interface – Controlling an Epica DGX 16 or 32” chapter on page 95.
  • Page 96 Under Time Sync, select Network Time and click Accept. Click the NIST Servers tab. FIG. 50 NIST Server Manager page Modify any of the settings on the NIST Servers page and click Accept. Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 97: Dod Security Mode

    NXB-AP-1000 Interface – Initial Setup by Network Admin DoD Security Mode Epica DGX 16 and 32 matrix switchers provide a DoD Security mode (for security profile settings, see the table on page 93). Important: When DoD Security mode is “on” a BCS tunnel is available; however, the NXB-AP-1000 interface is unavailable.
  • Page 98 NXB-AP-1000 Interface – Initial Setup by Network Admin three security profile To disable DoD Security mode for an Epica DGX 16 or 32: settings table Insert one end of an RJ-45 cable into a network card on a PC. Insert the other end of the cable into the TCP/IP port on the enclosure.

  • Page 99: Icsp Support

    Controller for SEND_COMMANDs that include standard BCS commands and connect to Port 3 for any SEND_COMMANDs that include diagnostic or auxiliary BCS commands. Port 1 is reserved for future functionality. For Epica DGX 16/32 NetLinx Programming information, see page 105. Epica DGX 16 and Epica DGX 32 Instruction Manual...
  • Page 100 NXB-AP-1000 Interface – Initial Setup by Network Admin Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 101: Nxb-Ap-1000 Interface - Controlling An Epica Dgx 16 Or 32

    IP Control drop down menu and selecting Controller. The directions in this chapter assume the following: The Epica DGX 16 or 32 has been connected via the TCP/IP port to a LAN or to a PC (see page 42). The NXB-AP-1000 Interface has been accessed (see page 81).
  • Page 102 NXB-AP-1000 Interface – Controlling an Epica DGX 16 or 32 Note: Multiple independent AMX AutoPatch Routing Systems (each with server connection) can be controlled from a single PC. Each NXB-AP-1000 Interface can be assigned a unique IP address. The individual addresses can then be entered as needed in the browser. The IP address displays at the top of the XBar Controller, indicating which XBar you are using.
  • Page 103 NXB-AP-1000 Interface – Controlling an Epica DGX 16 or 32 To execute or disconnect switches on the XBar: Access the XBar using the instructions on page 95. The XBar opens. Optional (to change the virtual matrix) – Click the VM title block in the upper left corner.
  • Page 104 NXB-AP-1000 Interface – Controlling an Epica DGX 16 or 32 Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 105: Nxb-Ap-1000 Interface - Additional Info For Network Admin

    Click the Browse (...) button to navigate to the target directory. From the Files list, select the appropriate .KIT file. Enter the Device and System ID Numbers for the Epica DGX 16 or 32 in the Device and System text boxes.

  • Page 106: Embedding The Xbar Applet

    <param name = "InitialVM" value = "0"> <param name = "VMLockDown" value = "locked"> <param name = "AllowGain" value = "true"> <param name = "AllowVolume" value = "true"> </APPLET> </BODY> </HTML> Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 107: Changing The Proxy Setting

    Check all power, signal, and link connections on all of the equipment. Check LED indicators for the TCP/IP (RJ-45) connector on the Epica DGX 16 or 32. If the LED indicators are not illuminated, check the cable type to make sure it meets cable requirements (see page 43).
  • Page 108 If the Proxy server box is checked, go to Step 4. If the Proxy server box is not checked, check it before going to Step 4. Be sure Proxy server box is checked Epica DGX 16 and Epica DGX 32 Instruction Manual...
  • Page 109 Enter NXB-AP-1000 Interface IP address In the Exceptions field, enter the appropriate NXB-AP-1000 Interface IP address (see page 80). Click OK to exit each of the dialog boxes used in these steps. Epica DGX 16 and Epica DGX 32 Instruction Manual...
  • Page 110 NXB-AP-1000 Interface – Additional Info for Network Admin Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 111: Epica Dgx 16/32 Netlinx Programming

    The Epica DGX 16/32 recognizes NetLinx SEND_COMMANDs with embedded BCS commands. Use NetLinx Studio (Version 3 or higher is required) to send these commands to the Epica DGX 16/32, or use these commands in standard compiled NetLinx Programming code running on a NetLinx Master.

  • Page 112: Send_Commands

    Port 3. SEND_COMMANDs for the Epica DGX 16/32 are not limited to the ones in the tables but can include additional BCS commands as well. For complete information on BCS commands, see the Instruction Manual –...
  • Page 113 • L# = level number (virtual matrix number) either 0 or 1 (both switch video level, omit L<L#>.) along with any embedded audio) • I# = input port number for Epica DGX 16: 1-16 = Inputs 1-16 • O# = output port number for Epica DGX 16: 1-16 = Outputs 1-16 •...
  • Page 114 Epica DGX 16/32 NetLinx Programming Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 115: Appendix A - Edid Programmer

    Matrix Switchers and EDID Matrix switchers, such as the Epica DGX 16/32, provide the ability to route one source signal to many potentially different types of display devices. Through the use of compatible DGX SC Fiber Receivers featuring SmartScale™, in almost all cases, incompatibilities between source device resolutions and...

  • Page 116: Determining The Need For Edid Programming

    Epica DGX 16 or 32 to each of the destination devices. If they can be routed, then EDID programming is not necessary.

  • Page 117: Reading And Saving Edid Data From A Destination Device

    Appendix A – EDID Programmer To install EDID Programmer software: Locate and open the installer <EDIDProgrammer_1.2.exe> on the AMX AutoPatch CD or at www.amx.com. Follow the directions in the wizard. Reading and Saving EDID Data from a Destination Device Tip: The Save button in the EDID Programmer can be used to save the EDID information as an .edid file, which can be opened as a text file (click on the Open button) and edited or opened and...

  • Page 118: Writing Edid Data To Epica Dgx 16 Or 32 Dvi Input Connector

    Attach a null modem serial cable without hardware flow control to the serial port (DB-9) on the Epica DGX 16 or 32. Use a serial cable that matches the pin diagram in FIG. 56 for RS-232. AMX AutoPatch equipment uses pins 2, 3, and 5 only.
  • Page 119 14. Disconnect the DVI video cable from the PC and from the Epica DGX DVI Input Board. 15. Disconnect the serial cable from the PC and from the Epica DGX 16 or 32 enclosure. Epica DGX 16 and Epica DGX 32 Instruction Manual...
  • Page 120 Appendix A – EDID Programmer Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 121: Appendix B - Managing Configuration Files

    Matrix being configured. Note: If you use the advanced feature of creating a new virtual matrix (VM), be aware that the Control Panel for the Epica DGX 16 and 32 supports a maximum of two digits for virtual matrix numbers.

  • Page 122: Overview

    XNConnect to discover the .xcl file on the CPU or use XNConnect to open a copy of the .xcl file. The .xcl file copy is provided on the AMX AutoPatch CD (MyXCL folder). In either case, after the configuration is modified in XNConnect, it is loaded back onto the CPU (replacing the original file).

  • Page 123: Installing And Launching Xnconnect

    Appendix B – Managing Configuration Files AMX AutoPatch CD Information If you cannot locate the AMX AutoPatch CD that shipped with your system and your AMX account has the required permissions, you can download the newest version of XNConnect from www.amx.com.

  • Page 124: Discovering A System

    Discover the system (recommended). This works for both conventionally and automatically configured systems (see page 116). Open a copy of the .xcl file located in the MyXCL folder on the AMX AutoPatch CD. The .xcl file is only available on the CD if the system was conventionally configured (see page 116).

  • Page 125: Opening An .Xcl Configuration File

    Use the standard Open dialog box to locate and open the .xcl configuration file. The default location is in the MyXCL folder on the AMX AutoPatch CD. From the File menu, select Save As and save an .xcl file with a new name to the PC.

  • Page 126: Navigating The Interface

    Properties of highlighted device Primary Components of the device primary device This view will show any linked AMX AutoPatch primary devices Communication settings Device firmware version FIG. 59 XNConnect interface with Hardware tab selected Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 127: Modifying An .Xcl Configuration File

    Discover the system (see page 118) or open the .xcl file (see page 119). In the Hardware view, right-click the Control Panel icon (CP-15 style). If the Control Panel icon is not displayed, double-click the Epica DGX 16 or 32 icon. Select Set Password from the drop-down menu.
  • Page 128 The process for creating local presets involves three dialog boxes that cover managing, naming, and modifying presets. The Epica DGX 16 and 32 each support a maximum of 64 local presets. The instructions following are for creating a local preset. For detailed information on modifying and deleting local presets, see the XNConnect Help file.
  • Page 129 (We strongly recommend making a duplicate copy every time the file is modified.) 14. Reload the .xcl file from the CPU to the Control Panel according to the directions on page 75. Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 130: Loading An .Xcl Configuration File

    PC. (We strongly recommend making a duplicate copy every time the file is modified.) Connect the Epica DGX 16 or 32 enclosure to the PC (see page 29). (For systems with multiple enclosures, you can connect any of the enclosures to the PC as long as all the enclosures are linked together.)

  • Page 131: Device Discovery Support

    However, certain conditions may warrant a custom string, such as the need to limit the VMs that are available for control by an AMX control system. Or a need may exist to limit the features available for a system, e.g., omitting the ability to adjust input gain, but leaving support for output volume in an Epica DGX 16 or 32 system that links to enclosures with adjustable audio.
  • Page 132 Appendix B – Managing Configuration Files Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 133: Appendix C - Apdiagnostics

    Note: The default port when APDiagnostics is first launched is the Ethernet (Enc Link) port. To install APDiagnostics using an Enc Link port (recommended): Connect an RJ-45 cable to an Enc Link (Ethernet 10/100) port on the Epica DGX 16 or 32. Attach the other end of the RJ-45 cable to a PC.
  • Page 134 Attach a null modem serial cable without hardware flow control to the Control (DB-9 serial) port on the Epica DGX 16 or 32. Use a null modem cable that matches the pin diagram below for RS-232. AMX AutoPatch equipment requires pins 2, 3, and 5 only.

  • Page 135: Modes

    AutoPatch Distribution Matrix. For this mode to be used effectively, we recommend using a dedicated PC because the Epica DGX 16 or 32 must be connected to your PC via an Enc Link (Ethernet 10/100) port (default) or Control (DB-9 serial) port and the program must be running continuously to acquire data.
  • Page 136 * A fan should be replaced if the speed drops significantly lower than its setting value, indicating that it will eventually fail. If a fan has failed completely, its speed will be reported as 0 RPM. Epica DGX 16 and Epica DGX 32 Instruction Manual...
  • Page 137 Warning or Error setpoint, the color of the meter changes from green (Good) to yellow (Warning) or red (Error), making it easy to identify problem areas at a glance. Epica DGX 16 and Epica DGX 32 Instruction Manual...
  • Page 138 Note: The Signal Sense table does not show crosspoint status. Epica DGX 16 and Epica DGX 32 Instruction Manual...
  • Page 139 Notices, Warnings, Errors, and Async Network Msgs (Messages). Tabs Data Lines Note: A yellow or red outline around a data line indicates that the component was previously in a Warning or Error state. Epica DGX 16 and Epica DGX 32 Instruction Manual...
  • Page 140 Advanced users can open .acp files with a packet/ network analyzer, such as “Analyzer” (http://analyzer.polito.it/). Activity (.log) – displays system activity in the Activity Log dialog box in text format. Epica DGX 16 and Epica DGX 32 Instruction Manual...
  • Page 141 History is 168 hours. For default values, see the dialog box.) Large history sets may impede performance of the application, so set this value in accordance with the resources available on the target PC. Epica DGX 16 and Epica DGX 32 Instruction Manual...
  • Page 142 APDiagnostics is running in Acquisition mode. You can also specify how big the active Log file should get before it is archived and a new one is started. These parameters are specified on the Logging tab. Browse parent directory for log files Epica DGX 16 and Epica DGX 32 Instruction Manual...
  • Page 143 LogFiles > Activity in the installation directory). Open the desired .apd and/or .zip file(s). The Status bar at the bottom indicates which file is being processed (for example, “Processing file 2 of 3”). Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 144: Communications

    2) Open Network Connections. 3) Right click on the Local Area Connection (under LAN or Internet) and select Properties. 4) Hover the mouse pointer over the entry in the Connect Using field to display the MAC Address (e.g., 00-1E-4F-A1-82-5D). Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 145: Appendix D - Programmer's Interface For System Diagnostics

    PC. * AMX reserves the right to add to the contents of the splash screen at any time, without notice. ** Verbosity (i.e., wordiness) refers to the amount of information provided; the higher the verbosity setting, the more information is displayed.

  • Page 146: Using Bcs To Access System Diagnostic Information

    Enter the verbosity level setting v# and the component identity setting i#. Either may be specified first. Enter ! (to send the command). Example ~scrv3i6! or ~scri6v3! (Either displays the highest level of detail for the Power System.) Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 147: Splash Screen Examples

    Appendix D – Programmer’s Interface for System Diagnostics Splash Screen Examples Note: AMX reserves the right to add to the contents of the splash screen at any time, without notice. Power-Up Splash Screen The first example is of the splash screen that displays when power is applied to the enclosure. When “Ready”...
  • Page 148 [output power] 33.795w Scroll to see additional information [voltage] 11.858V [current] 2.850a [fan speed] 20100 rpm [service hours] 2 [model#] FNP850-12ARG [serial#] 101455-0003R FIG. 66 Display for v3i6 (verbosity 3, component 6) Epica DGX 16 and Epica DGX 32 Instruction Manual...
  • Page 149 Scroll to see additional information [board 2] c0e0 [board 3] 0000 [board 4] 0000 [output boards] count = 2 [board 5] 80b0 [board 6] 80b0 FIG. 67 Display for v3i4 (verbosity 3, component 4) Epica DGX 16 and Epica DGX 32 Instruction Manual...
  • Page 150 Appendix D – Programmer’s Interface for System Diagnostics Epica DGX 16 and Epica DGX 32 Instruction Manual...

  • Page 151: Appendix E - Board Replacement

    This appendix covers the removal and replacement procedure for boards for input and output boards for the Epica DGX 16 and 32 (see tables). Epica DGX boards are hot-swappable, i.e., the procedure can be done while the system is powered up (see the “Caution” at the bottom of this page).

  • Page 152: Safety Recommendations For Laser Products

    In almost all cases, Epica DGX 16 and 32 systems are configured to accommodate a full enclosure’s worth of boards and do not require modification to the configuration file when a board is added. If you cannot execute switches with the new board after it has been installed, the configuration file may need to be updated;...
  • Page 153 Blank board plate – Remove the screw that holds the board plate in place (for the Epica DGX 32, see FIG. 69; for the Epica DGX 16, see FIG. 70). Pull the plate out of the board slot opening (the tab on the end of the board plate fits in a slot near where the ejector handle would otherwise go).
  • Page 154 The bend radius for AMX SC terminated fiber cables is 2 inches (5 cm). 11. Attach the cables to the board’s connectors* and reconnect any other cables that were disconnected in Step 3 (if applicable –...

  • Page 155: Board Troubleshooting

    The default configuration that ships with almost all systems includes two VMs (VM 0 and VM 1) with the crosspoint size for each set at a full 32x32 for an Epica DGX 32 (eight input and eight output boards) and at 16x16 for an Epica DGX 16 (four input and four output boards). ~scri5v3! [5:VM Configuration] count = 2 Standard VM count is “2”...
  • Page 156 Appendix E – Board Replacement Epica DGX 16 and Epica DGX 32 Instruction Manual...
  • Page 157 - Schedules and registration for any AMX University course - Travel and hotel information - Your individual certification requirements and progress It’s Your World - Take Control™ 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.222.0193 • 469.624.8000 • 469-624-7153 fax • 800.932.6993 technical support • www.amx.com...

This manual is also suitable for:

Epica dgx 32Enova dgx 16

Table of Contents