AMX Enova DGX 8 Quick Start Manual

Overview
Enova DGX 8/16/32/64 Digital Media Switchers are available in various configurations
in increments of four up to 8x8, 16x16, 32x32, and 64x64 respectively. Therefore, the
illustrations in this guide may differ from the model(s) purchased. Each enclosure contains
an integrated NetLinx Central Control Processor . For complete documentation (including
system and board specifications and supported resolutions), see the Instruction Manual –
Enova DGX 8/16/32/64 Digital Media Switchers at www.amx.com.
Installation
Rack Mounting
Caution: To prevent overheating, avoid placing high heat-producing equipment directly
above/below enclosure. The system requires a minimum of 1 empty rack unit above and
below (3 empty rack units are recommended). Verify that the openings on the sides and
top of the enclosure are not blocked and do not have restricted airflow.
To rack mount Enova DGX 8/16/32 enclosure
1. Position enclosure in rack and secure it with rack mounting screws.
2. Provided / recommended for DXLink Fiber Boards – Install cable management bars:
Fasten bar with two screws on one end of the board and one screw at the other
(the long part of the bar is to the right of holes); do not over tighten. Enova DGX 32
only – Remove number plate at rear top; replace the number plate when finished.
* When fully loaded, the Enova DGX 32 weighs approx. 73 lbs (33.1 kg).
To rack mount Enova DGX 64 enclosure
1. While shipping box is still on the pallet, cut and remove outer straps.
2. Remove cardboard tray from top of reusable shipping box (note wheels on box).
3. Lift box off pallet (Enova DGX 64 weighs approx. 150 lbs [68.0 kg] fully loaded).
Ensure all parties involved in lifting are prepared and follow local requirements.
4. Unlock 4 latches on sides of shipping box. Lift top of box straight up and set aside.
5. Attach 2 handles provided for lifting; use 4 of 6 holes on side, in front or rear position.
6. Using bottom of shipping box, roll the enclosure into position. Lift onto temporary
shelf/support in rack. Align as closely as possible and then remove lifting handles.
7. Lift into position and screw in rack ear screws.
8. Provided/recommended for DXLink Fiber Boards – Install cable management bars:
Fasten bar with two screws on one end of the board and one screw at the other (the
long part of the bar is to the right of holes); do not over tighten.
Attaching Input and Output Cables
Generally, any input board in an Enova DGX Switcher can route signals to any type of
output board; the signal format is automatically converted to match the output board.
DXLink™ Twisted Pair Input and Output Boards require DXLink™ Twisted Pair
Transmitters and Receivers. DXLink™ Fiber Input and Output Boards require DXLink™
Fiber Transmitters and Receivers. For details, see each product's Quick Start Guide or
Instruction Manual.
For testing purposes, attach just the first two source and destination devices (and any
required transmitters or receivers).
Enova DGX AIE, HDMI, DVI, DXLink Twisted Pair, and DXLink Fiber Boards
AIE Board – This board is documented separately. Before wiring audio, AIE boards
must be uninstalled, have their DIP switches set, and be reinstalled. For directions, see
the Quick Start Guide - Enova DGX Audio Insert/Extract Board.
HDMI Board
DVI Board
DXLink TP Board
DXLink Fiber Board
AIE Board
FIG. 1 HDMI, DVI, DXLink Twisted Pair, DXLink Fiber, and AIE Boards
HDMI Boards (HDCP 1.4) – Inputs and outputs incorporate HDMI
HDMI connectors route high-resolution HDMI or DVI signals with or without HDCP.
For single-link DVI signals, use a cable adapter.
DVI Boards (HDCP 1.4) – Inputs and outputs are HDMI compatible. DVI output pin 14
(+5 VDC out) supplies 50 mA per each of the four output connectors. By changing the
EDID, DVI Boards can route HDMI.
Note: If an HDCP signal is switched from an HDMI or DVI Output Board to a destination
which does not support HDCP or to an SC Optical Output Board (no HDCP support), a
dark red image displays indicating authentication failure. For HDCP signals switched via
DXLink (Twisted Pair or Fiber), authentication failure is indicated by an orange image.
DXLink Twisted Pair Boards (HDCP 1.4) – Inputs and outputs incorporate HDMI
technology. Use with DXLink Twisted Pair Transmitters / Receivers, which automatically
adjust the scaling and image and almost always result in a quality image on the monitor.
If the setup has special requirements or adjustment is needed, see the Instruction
Manual.
Enova DGX 8/16/32/64 Digital Media Switchers
(DGX 32* requires 2 people min.)
(requires 3 people minimum)
Note: The Instruction Manual contains information on:
• InstaGate Pro Technology (easy switching of
HDCP protected content) for HDMI
• Software for scaling and EDID programming
Note: System setup for DXLink Twisted Pair
Boards is similar to FIG. 2, only with DXLink
Twisted Pair TXs and RXs installed between
the DXLink Twisted Pair Boards and the
source and destination devices.
®
technology.
DXLink Fiber Boards (HDCP 1.4) – Inputs and outputs incorporate HDMI technology.
DXLink Fiber boards and units are available for duplex and simplex functionality (with
multimode and single mode options for each) for various system requirements. Use with
DXLink Fiber Transmitter / Receiver units, which automatically adjust scaling and image,
resulting in a quality image on the monitor. If the setup has special requirements or
adjustment is needed, see the Instruction Manual.
Warning: DXLink Fiber units use laser transceivers, which are Class 1 Eye Safe per
IEC 60825-1/CDRH requirements. Class 1 category indicates that invisible laser used is
safe; we recommend avoiding direct eye exposure when using any optical fiber products.
Caution: For DXLink Fiber Boards and SC Optical Boards, we recommend using the
provided cable management bars or some other type of cable management system to
avoid damage to fiber cables.
Important: DIP switches must be set on the DXLink Twisted Pair and DXLink Fiber
Transmitters and Receivers before units are cabled to the switcher via their boards. For
:
information on DXLink Twisted Pair modules and wallplates or DXLink Fiber Transmitters
and Receivers, see the applicable "Quick Start Guide."
:
FIG. 2 DXLink fiber cable attached to input; system setup with DXLink Fiber units
Note: Epica DGX SC Fiber Boards are also compatible with Enova DGX Switchers. For
information on SC Optical boards when used in an Enova DGX Switcher, see the
"Instruction Manual – Enova DGX 8/16/32/64 Digital Media Switchers."
Audio EDID Settings
HDMI, DVI, DXLink Twisted Pair Boards ship with a basic audio EDID configuration.
DXLink Fiber Boards obtain EDIDs upon connection to their Transmitters. To optimize
audio for your system, you may need to change the EDID settings. Custom EDID files
and DGX Configuration Software are available at www.amx.com. For information, see the
Instruction Manual for the Enova DGX or look in the software's Help file.
DGX Board Custom EDID Files*
• 1080p (VIC 16): AMX_HDMI1v3__Standard.edid
• 1080p (VIC 16): AMX_HDMI1v3_A__Surround.edid
• 720p (VIC 4):
• 720p (VIC 4):
* The custom files listed are in the AMX_EDID_Library at www.amx.com along with
additional EDID files that support 3D deep color and High Bit Rate (HBR) audio.
1
- Supports basic audio only: 2Ch L-PCM sample rates of 32 kHz, 44.1 kHz, 48 kHz.
2
- Supports up to 192 k for 48 kHz Dolby (5.1), and 48 kHz DTS (5.1), and 2Ch L-PCM
sample rates of 32 kHz, 44.1 kHz, 48 kHz.
Note: File names containing "AMX_HDMI1v3" do not refer to the HDMI v1.3 standard.
Applying Power and Startup
The Enova DGX 8/16/32 each have two power supplies, and the Enova DGX 64 has four.
Note: We recommend using a surge protector and/or an AC line conditioner.
Important: If the system is used to power DXLink Twisted Pair TXs and/or RXs, use the
"Enova DGX Configuration Tool" at www.amx.com/enova to calculate the power draw.
Important: Enova DGX 64 only
the CPU and the control panel will continue to operate. However, input and output boards
will become inoperable and the system will not send or receive signals until at least three
power supplies resume functional status.
For proper redundant operations, all power supplies must be powered at all times.
• Enova DGX 8/16 - Cable power via power strip to outlet connected to single 20 A
circuit.
• Enova DGX 32 - Cable primary power feed to outlet connected to one 20 A circuit
breaker. Cable redundant power feed to outlet connected to a second 20 A circuit
breaker.
• Enova DGX 64 - To provide adequate power for an N+1 redundant application,
connect each of the 4 power supplies to its own circuit.
To apply power:
1. Plug power cords into all power receptacles (Enova DGX 64 only – use provided AC
power filtering clamp-on Ferrites on cords as close to power supplies as possible).

Quick Start Guide

DXLink Fiber connector
(make sure it seats firmly;
normally a click is heard)
System Setup
DXLink Fiber RX
DXLink Fiber TX
Enova DGX Switcher
DXLink Fiber Input
DXLink Fiber Output
1
2
1
AMX_HDMI1v3_B__720p.edid
AMX_HDMI1v3_C__720p_Surround.edid
- If two or more power supplies are not receiving power,
Note: Avoid network loops
(created when an enclosure
and one or more TX/RX units
in a system are connected to
a common LAN).
2