Korg MMT RADIAS Owner's Manual page 144

Effect guide
InitPhase (LFO Init Phase)
Sets the starting location of the waveform. This parame-
ter will be displayed and can be set if "Key Sync" is Tim-
bre.
☞p.125 "InitPhase (LFO Init Phase)"
LFOSpread (LFO Spread)
Sets the LFO phase difference between the left and right
channels.
High Damp
Sets the feedback damping amount in the high range.
24. St.Tremolo (Stereo Tremolo)
This effect modulates the volume level of the input sig-
nal. The effect is stereo, and offsetting the LFO of the left
and right phases from each other produces a tremolo ef-
fect between left and right.
Stereo In - Stereo Out
Left
Right
LFO
Dry/Wet
Sets the balance between the effect and dry sounds.
Mod Depth (Modulation Depth)
Sets the depth of LFO modulation.
TempoSync (LFO Tempo Sync)
Specifies whether the LFO cycle will be synchronized
with the tempo specified by the [TEMPO] knob or MIDI
clock.
☞p.125 "TempoSync (LFO Tempo Sync)"
LFO Freq (LFO Frequency)
Sets the LFO speed.
☞p.125 "LFO Freq (LFO Frequency)"
Sync Note (LFO Sync Note)
Sets the LFO frequency as a proportion of the tempo set
by the [TEMPO] knob. This parameter will be displayed
and can be set if "TempoSync" is On.
☞p.125 "Sync Note (LFO Sync Note)"
LFO Wave (LFO Waveform)
Selects the LFO waveform.
☞p.125 "LFO Wave (LFO Waveform)"
LFO Shape
☞p.125 "LFO Shape"
138
[000...180°]
[–180...+180°]
[000...100%]
Tremolo
Tremolo
LFO Spread
LFO Shape
[Dry, 99:1...1:99, Wet]
[000...127]
[0.01...100.0Hz]
[8/1...1/64]
[Saw, Squ, Tri, Sin, S&H]
[–63...+63]
Key Sync (LFO KeySync)
Specifies whether the LFO will be reset by note-on.
☞p.125 "Key Sync (LFO KeySync)"
InitPhase (LFO Init Phase)
Sets the starting location of the waveform. This parame-
ter will be displayed and can be set if "Key Sync" is On.
☞p.125 "InitPhase (LFO Init Phase)"
LFOSpread (LFO Spread)
Sets the LFO phase difference between the left and right
channels.
25. St.Ring Mod
(Stereo Ring Modulator)
This effect creates a metallic sound by applying the os-
cillators to the input signal. Use the LFO or Dynamic
Modulation to modulate the oscillator to create a radical
modulation. Matching the oscillator frequency with a
Dry / Wet note number will produce a ring modulation effect in
specific key ranges.
Stereo In - Stereo Out
Left
Dry / Wet
Right
Fixed Frequency
Note Offset, Fine
Note No.
LFO
Dry/Wet
[Off, On] Sets the balance between the effect and dry sounds.
OSC Mode
Switching between specifying the oscillator frequency
and using a note number.
If this is set to Note, the oscillator frequency will track
the note of the input signal.
FixedFreq (Frequency)
This parameter sets the oscillator frequency when "OSC
Mode" is set to Fixed.
If this parameter is assigned to "Edit1," "Edit2," or
"Edit," setting "OSC Mode" to Note will switch
the assignment to NoteOfst.
NoteOfst (Note Offset)
Sets the pitch difference from the original note in semi-
tone steps when "OSC Mode" is set to Note.
NoteFine
Sets the pitch difference from the original note in cent
steps when "OSC Mode" is set to Note.
[Off, Timbre]
[000...180°]
[–180...+180°]
Pre LPF
Ring Modulator
Pre LPF
Ring Modulator
Fixed Oscillator
Pitch
OSC Mode
Note (Key Follow)
[Dry, 99:1...1:99, Wet]
[Fixed, Note]
[0Hz...12.0kHz]
[–48...+48]
[–100...+100]
Dry / Wet
Dry / Wet