Extension Cords; Specifications - Craftsman 351.221160 Operator's Manual

• Many cover plate screws, water pipes and outlet boxes are
not properly grounded. To ensure proper ground, grounding
means must be tested by a qualified electrician.
EXTENSION CORDS
• The use of any extension cord will cause some drop in
voltage and loss of power.
• Wires of the extension cord must be of sufficient size to
carry the current and maintain adequate voltage.
• Use the table to determine the minimum wire size (A.W.G.)
extension cord.
• Use only 3-wire extension cords having 3-prong grounding
type plugs and 3-pole receptacles which accept the tool plug.
• If the extension cord is worn, cut, or damaged in any way,
replace it immediately.
Extension Cord Length (120V Operation)
Wire Size A.W.G.
Up to 25 ft....................................... 14
Up to 50 ft....................................... 12
NOTE: Using extension cords over 50 ft. long is not
recommended.
ELECTRICAL CONNECTIONS
WARNING: Make sure unit is off and disconnected from
power source before inspecting any wiring.
The saw is prewired for use on a 120 volt, 60HZ power supply.
The power lines are inserted directly onto the switch. The
green ground line must remain securely fastened to the frame
to properly protect against electrical shock.
240 VOLT OPERATION
• To use the saw with a 240V, single-phase power supply,
have a qualified electrician attach a 240 volt, 15A 3-prong
plug onto saw line cord and install the proper connectors
and receptacles to power supply.
• See wiring diagram (Figure 6) for wiring instructions.
( 1 } { 4 }
L1 120V L2
2 }
( 1 ) Q 4
1 ;
L1 240V L2
Figure 6 - Wiring Schematic
Refer to Figures 7-10, pages 16 and 23.
DESCRIPTION
The Craftsman 10" Model Number 221160 tilting arbor saw
offers precise cutting performance for all woods up to 3X_"
thick. The saw is designed for the professional user and is
ruggedly constructed for continuous service. The saw is
designed to be permanently located in a shop or plant. The
10" Saw is recommended for use with a 10" blade.
The saw features an extra large solid granite table. A unique
system of T-slots incorporate the cast iron miter gauge. Saw is
equipped with a riving knife and a clear acrylic blade guard
with antikickback feature. Cabinet is constructed of heavy
gauge welded steel, totally enclosed and is ported for a 4"
vacuum hose.
Rip Fence Assemby features a heaw-duty precision rip fence
that is designed for simple and one-hand maneuverability.
They include a front rail calibrated in inches and millimeters
with a magnified window for close tolerances.
SPECIFICATIONS
Capacity with 10" Blade:
Depth of cut at 90 ° . ............................. 3_6"
Maximum tilt angle of arbor ........................ 45 °
Depth of cut at 45 ° . .............................. 214"
Max. cut right of blade with rip fence ................. 30"
Max. cut left of blade with rip fence ................. 131/2"
Saw Dimensions:
Table height .................................... 34"
Cabinet depth ................................... 20"
Cabinet width .................................. 17¾"
Table area ................................ 40X" x 27"
Front of table to blade ............................ 12"
Rip Fence Dimensions:
Rip fence ..................................... 37%"
Rip fence rails (front and rear) ...................... 52"
Blade capacity maximum .......................... 10"
Blade arbor extension ............................. %"
Dado blade capacity maximum ..................... _6"
Saw Constructions:
Cabinet ................... Totally enclosed welded steel
Table ....................................... Granite
Rip fence ......................... UPE and steel tube
Drive system .............................. Poly V-belt
Exhaust port ................................ 4" Male
Miter gauge .............. Cast iron with T-slot roller guide
Blade guard .............. Acrylic with antikickback pawls
Switch .................... ON/OFF switch with overload
Arbor R.P.M........................ 4,000 RPM approx.
Motor: ................. I_HP, 3450 RPM, capacitor start,
capacitor run, 120/240V, 15/7.5A,
single-phase, ball bearing
Weight ..................................... 432 Ibs
Shipping weight .............................. 485 Ibs
WARNING: Disconnect power before attempting any of the
following procedures. Be certain switch is in OFF position and
safety disconnect (or breaker) is in OFF or open position. Saw
blade must not be moving. Saw blade will rotate freely after
motor is turned off. Allow blade to come to a complete stop
before attempting any of the following procedures.
WARNING: The operation of any power tool can result in
foreign objects being thrown into the eyes, which can result in
severe eye damage. Always wear safety goggles complying
with United States ANSI Z87.1 before commencing power tool
operation.
9