Sony Digital Betacam DVW-707 Maintenance Manual page 31

No. Page Item
15 VF SETTING ZEBRA 1 DETECT
ZEBRA 1 APERTURE 1 to 20 % ([10])
ZEBRA 2 DETECT
ZEBRA SELECT
TEST OUT ZEBRA
VF DTL LEVEL
16 LEVEL 1 DETAIL LVL
H/V RATIO
DTL FREQ
CRISPENING
APT. LEVEL
DTL W.CLP
DTL V B.CLP
DTL H B.CLP
LVL DEPEND
L.DEP.LVL
17 LEVEL 2 KNEE APT
K.APT.LVL
DTL COMB
C.C.S.LVL
18 LEVEL 1#4:3
DETAIL LVL
H/V RATIO
DTL FREQ
CRISPENING
APT. LEVEL
DTL W.CLP
DTL V B.CLP
DTL H B.CLP
LVL DEPEND
L.DEP.LVL
19 LEVEL 2#4:3
KNEE APT
K.APT.LVL
DTL COMB
C.C.S.LVL
DVW-790WS/709WS/707
DVW-790WSP/709WSP/707P P2V1
Setup Description
20 to 107 % ([70]) Sets the center level of the zebra 1 pattern.
Sets the width of the zebra 1 pattern.
52 to 109 % ([100]) Sets the ZEBRA2 display level.
[1]/2/BOTH
Selects the zebra patterns.
ON/[OFF] Turns ON/OFF the function of outputting the zebra pattern to TEST OUT.
X ([0]) Sets the VF detail amount.
X ([0]) Sets the total level of the detail signal.
X ([0]) Sets balance between the H detail signal and the V detail signal.
X ([0]) Sets frequency (thickness) of the H detail signal.
X ([0]) Sets the crispening level of the detail signal.
X ([0]) Sets the high-frequency correction level.
X ([0]) Sets the white clip level of the V detail signal.
X ([0]) Sets the level that clips the excessive level in the negative (_)
direction of the V detail signal.
X ([0]) Sets the level that clips the excessive level in the negative (_)
direction of the H detail signal.
[ON]/OFF
Turns ON/OFF the level dependent function
X ([0]) Sets the level that suppresses the detail signal at the low signal level.
ON/[OFF] Turns ON/OFF the knee aperture function.
X ([0]) Adjusts the detail signal amount that is added to the high light
signal higher than the knee point.
X ([0]) Set the signal level at which the comb filter starts working.
X ([0]) Sets the chroma suppression level. (NTSC only)
Note : This page is displayed only in DVW-790WS/790WSP/
709WS/709WSP.
The following settings are valid when the 16:9/4:3 MODE
on the WIDE SCREEN is set to 4:3.
X ([0]) Sets the overall level of the detail signal.
X ([0]) Sets balance between the H detail signal and the V detail signal.
X ([0]) Sets frequency (thickness) of the H detail signal.
X ([0]) Sets the crispening level of the detail signal.
X ([0]) Sets the high frequency correction level.
X ([0]) Sets the white clip level of the V detail signal.
X ([0]) Sets the level that clips the excessive level in the negative (_)
direction of the V detail signal.
X ([0]) Sets the level that clips the excessive level in the negative (_)
direction of the H detail signal.
[ON]/OFF
Turns ON/OFF the level dependent function
X ([0]) Sets the level that suppresses the detail signal at the low signal level.
Note : This page is displayed only in DVW-790WS/790WSP/
709WS/709WSP.
The following settings are valid when the 16:9/4:3 MODE
on the WIDE SECREEN is set to 4:3.
ON/[OFF] Turns ON/OFF the knee aperture function.
X ([0]) Adjusts the detail signal amount that is added to the high light
signal higher than the knee point.
X ([0]) Set the signal level at which the comb filter starts working.
X ([0]) Sets the chroma suppression level. (NTSC only)
2-1. Service Mode
2-7