Table of Contents
Advertisement
Chapter 3
Pin #
Signal
48 (B16)
DRQ3
49 (B17)
DACK1*
50 (B18)
DRQ1
51 (B19)
REFRESH*
52 (B20)
SYSCLK
53 (B21)
IRQ7
54 (B22)
IRQ6
55 (B23)
IRQ5
56 (B24)
IRQ4
57 (B25)
IRQ3
58 (B26)
DACK2*
59 (B27)
TC
60 (B28)
BALE
61 (B29)
+5V
62 (B30)
OSC
63 (B31)
GND
64 (B32)
GND
Notes: The shaded area denotes power or ground. The signals marked with * = Negative true logic.
Table 3-7. PC/104 Interface Pin/Signal Descriptions (J14C)
Pin #
Signal
1 (C0)
GND
2 (C1)
SBHE*
3 (C2)
LA23
4 (C3)
LA22
30
Descriptions (J13 Row B)
DMA Request 3 – Used by I/O resources to request DMA service.
Must be held high until associated DACK3 line is active.
DMA Acknowledge 1 – Used by DMA controller to select the I/O
resource requesting the bus, or to request ownership of the bus as a bus
master device. Can also be used by the ISA bus master to gain control
of the bus from the DMA controller.
DMA Request 1 – Used by I/O resources to request DMA service.
Must be held high until associated DACK1 line is active.
Memory Refresh – This signal is driven low to indicate a memory
refresh cycle is in progress. Memory is refreshed every 15.6 usec.
System Clock – This is a free running clock typically in the 8MHz to
10MHz range, although its exact frequency is not guaranteed.
Interrupt Request 7 – Asserted by a device when it has pending interrupt
request. Only one device may use the request line at a time.
Interrupt Request 6 – Asserted by a device when it has pending interrupt
request. Only one device may use the request line at a time.
Interrupt Request 5 – Asserted by a device when it has pending interrupt
request. Only one device may use the request line at a time.
Interrupt Request 4 – Asserted by a device when it has pending interrupt
request. Only one device may use the request line at a time.
Interrupt Request 3 – Asserted by a device when it has pending interrupt
request. Only one device may use the request line at a time.
DMA Acknowledge 2 – Used by DMA controller to select the I/O
resource requesting the bus, or to request ownership of the bus as a bus
master device. Can also be used by the ISA bus master to gain control
of the bus from the DMA controller.
Terminal Count – This signal is a pulse to indicate a terminal count has
been reached on a DMA channel operation.
Buffered Address Latch Enable – This signal is used to latch the LA23
to LA17 signals or decodes of these signals. Addresses are latched on
the falling edge of BALE. It is forced high during DMA cycles. When
used with AENx, it indicates a valid processor or DMA address.
+5 volt power ±10%
Oscillator – This clock signal operates at 14.3MHz. This signal is not
synchronous with the system clock (SYSCLK).
Ground
Ground
Descriptions (J14 Row C)
Ground
System Byte High Enable – This signal is driven low to indicate a
transfer of data on the high half of the data bus (D15 to D8).
Lactchable Address 23 – This signal must be latched by the resource if
the line is required for the entire data cycle.
Lactchable Address 22 – Refer to LA23, pin-C2, for more information.
Reference Manual
Hardware
ReadyBoard 700
Advertisement
Table of Contents
