Yamaha M7CL Owner's Manual page 80

Signal flow for output channels
M
O
N
ST
MIX
MATRIX CUE
O
···
1 2 ··· 1516 L R (C) 1 2
■ MATRIX channels
These channels process the signals sent from MIX channels and STEREO/MONO channels to MATRIX buses, and send
them to the corresponding output ports. When the M7CL is in the default state, the following output ports are assigned.
• M7CL-32/48
MATRIX channels 1–8
Slot 3 output channels 1–8, 9–16
MATRIX channels 1/2
OMNI OUT jacks 13/14
M
O
N
ST
MIX MATRIX CUE
O
1 2 ··· 1516 L R (C) 1 2 ···
● ATT (Attenuator)
Attenuates/boosts the level of the signal.
● 4 BAND EQ (4 band equalizer)
A parametric EQ with four bands; HIGH, HIGH MID,
LOW MID, and LOW.
● DYNAMICS 1
This is a dynamics processor that can be used as a com-
pressor, compander, or expander.
● LEVEL
This adjusts the output level of the channel.
● BALANCE (STEREO channel only)
Adjusts the left/right volume balance of the STEREO (L/
R) channel.
● ON (On/off)
Turns the output channel on/off. If off, that channel is
muted.
● MATRIX ON/OFF (MATRIX send on/off)
This is an on/off switch for the signal sent from the MIX
channels, STEREO (L/R) channel, or MONO (C) channel
to each MATRIX bus.
● MATRIX (MATRIX send levels)
This adjusts the send level of the signal sent from the MIX
channels, STEREO (L/R) channel, or MONO (C) channel
to each MATRIX bus. As the position from which the sig-
nal is sent to the MATRIX bus, you can choose either,
immediately before the fader, or immediately after the
[ON] key.
80
M7CL Owner's Manual
7 8 L R
STEREO L,R,MONO(C)
To RACKIN PATCH INSERT POIN
To OUTPUT PACH POST ON INSERT OUT
STEREO
PRE FADER INSERT OUT
INSERT OUT L,R,MONO (C)
PRE EQ INSERT OUT
STEREO
INSERT IN L,R,MONO (C)
PRE EQ
METER
INSERT
PRE EQ POST EQ
PRE EQ
INSERT OUT
CUE ON
MATRIX1,3...7 LEVEL
MATRIX2,4...8 LEVEL
LEVEL
PAN
7 8 L R
MATRIX 1-8
To RACKIN PATCH
INSERT POINT
To OUTPUT PATCH
POST ON INSERT OUT
MATRIX
PRE FADER INSERT OUT
INSERT OUT 1-8
PRE EQ INSERT OUT
MATRIX
INSERT IN 1-8
PRE EQ
METER
INSERT
PRE EQ POST EQ
PRE EQ
INSERT OUT
CUE ON
EQ OUT DYNA OUT PRE FADER
METER METER METER
GR METER
LEVEL BAL
COMP
4BAND INSERT
COMPAND
ATT
EQ
EXPAND
PRE FADER
PRE FADER
INSERT OUT
Keyin
Self PRE EQ / Self POST EQ / MIX13-16 OUT /
ST (L,R,MONO (C)) POST EQ
(PRE FADER) PFL / (POST ON) AFL
ON
To MATRIX
PRE FADER / POST ON
ON
VARI
ON To MATRIX
PRE FADER / POST ON
VARI
STEREO
• M7CL-48ES (Daisy Chain)
MATRIX channels 1–6
MATRIX channels 1–4
MATRIX channels 1–8
EQ OUT DYNA OUT PRE FADER
METER METER METER
GR METER
LEVEL
COMP
INSERT
4BAND
ATT COMPAND
EQ
EXPAND
PRE FADER
PRE FADER
INSERT OUT
Keyin
Self PRE EQ / Self POST EQ / MIX13-16 OUT/
MATRIX1-8 POST EQ
(PRE FADER) PFL / (POST ON) AFL
If the send-destination MATRIX bus is set to stereo, you
can use the PAN knob to adjust the panning between the
two MATRIX buses. If the send-source is a stereo MIX
channel or the STEREO channel, use the BALANCE
knob to adjust the volume balance of the left and right
channels sent to the two MATRIX buses.
● INSERT
You can patch the desired output/input ports to insert an
external device such as an effect processor. You can switch
the insert-out and insert-in locations.
● METER
This meters the level of the output channel. You can
switch the position at which the level is detected.
● KEY IN (MIX channels 13–16 only)
You can send the output signals of MIX channels 13–16 to
dynamics processors and use them as key-in signals to
control the dynamics.
● RACK IN PATCH
This patches the output signal of the output channel to an
input of the rack.
● OUTPUT PATCH
This assigns an output port to an output channel.
● MONITOR SELECT
This selects the output signal of an output channel as a
monitor source.
POST ON
METER
ON STEREO OUT
L,R,MONO (C)
INSERT
To OUTPUT PATCH
To MONITOR SELECT
POST ON
POST ON
INSERT OUT
EtherSound output channels 17–22
OMNI OUT jacks 1–4
Slot 3 output channels 1–8, 9–16
POST ON
METER
ON
MATRIX OUT 1-8
INSERT
To OUTPUT PATCH
To MONITOR SELECT
POST ON
POST ON
INSERT OUT