Download Print this page
Hide thumbs Also See for M7CL:

Advertisement

M7CL Upgrade Guide
This document explains how to update the latest firmware (V3.x) for the M7CL (M7CL-48, M7CL-32,
M7CL-48ES), and how to update the firmware for the EtherSound module built into the M7CL-48ES.
Precautions (Please be sure to read this section first!)
・ The user assumes full responsibility for the update.
・ If you update the firmware V1 or V2 to V3, or V3.0x to V3.5x, all the M7CL internal data will be
initialized. Make sure to back up the internal data before updating. The data saved in a previous
version can be loaded into a system in a later version.
・ If you fail to follow these instructions properly, or turn off the M7CL or remove the USB storage device
while the update is in progress, the M7CL may be damaged.
・ If the M7CL does not work properly after updating, and you've tried updating several times, please contact
your Yamaha dealer.
・ Yamaha Corporation owns exclusive copyrights for the M7CL firmware, its update program, and this
documentation.
・ AuviTran owns exclusive copyrights for the EtherSound firmware and its update program.
・ Reproducing or modifying all or part of this documentation without permission is strictly prohibited.
・ EtherSound is a registered trademark of Digigram S.A.
・ Windows is a registered trademark of Microsoft ® Corporation in the United States and other countries.
・ The company names and product names in this document are the trademarks or registered trademarks of
their respective companies.
M7CL Upgrade Guide
1

Advertisement

loading

Summary of Contents for Yamaha M7CL

  • Page 1 ・ The user assumes full responsibility for the update. ・ If you update the firmware V1 or V2 to V3, or V3.0x to V3.5x, all the M7CL internal data will be initialized. Make sure to back up the internal data before updating. The data saved in a previous version can be loaded into a system in a later version.
  • Page 2: Preparing For The Update

    If you are saving the data to the USB storage device, open the SAVE/LOAD popup window from the SETUP screen. IMPORTANT: If you update the firmware V1 or V2 to V3, or V3.0x to V3.5x, all the internal data will be initialized. Make sure to back up the internal data before updating.
  • Page 3 When a "Since M7CL was upgraded, Initialize all memories" popup window appears, press the CLOSE button to close it. Press the EXIT button on the lower right of the startup menu screen to start up in normal mode. Remove the USB storage device after confirming the ACCESS indicator has disappeared in the function access area.
  • Page 4 This completes the update procedure of the M7CL firmware. If you have backed up the necessary data, load it using the M7CL SAVE/LOAD function or the M7CL Editor (compatible with the updated firmware version). If a password has been set for Administrator, set the password again.
  • Page 5 ・You may be prompted to restart the computer after the installation is complete. Before proceeding to step 3, restart the computer. Connect the EtherSound [IN] jack on the rear panel of the M7CL-48ES unit to the Ethernet jack on the computer using an Ethernet cable.
  • Page 6 Check the box to the left of the device description listed in the “EtherSound Devices” section. NOTE ・If no device is listed, click the [Refresh] button. If still no device is listed, your computer may not be properly connected to the M7CL-48ES.Please make sure that the cable is not disconnected or damaged, that you have selected the correct network adapter, and that the M7CL-48ES has started in Normal mode.
  • Page 7 Make sure that the firmware version displayed in the “EtherSound Devices” section matches the firmware version to which you just updated. If the version numbers do not match, the update operation may have failed. Try the update operation again, starting from step 8.

This manual is also suitable for:

M7cl-48M7cl-32M7cl-48es