Yamaha M7CL Owner's Manual page 259

■ REV→FLANGE
One input, two output reverb and flanger effects in series.
Parameter Range
REV TIME 0.3–99.0 s Reverb time
INI. DLY 0.0–500.0 ms Initial delay before reverb begins
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
DIFF. 0–10 Spread
DENSITY 0–100% Reverb density
Reverb and flanged reverb bal-
REV.BAL 0–100% ance (0% = all flanged reverb,
100% = all reverb)
THRU, 21.2 Hz–
HPF High-pass filter cutoff frequency
8.00 kHz
50.0 Hz–16.0 kHz,
LPF Low-pass filter cutoff frequency
THRU
FREQ. 0.05–40.00 Hz Modulation speed
DEPTH 0–100% Modulation depth
MOD. DLY 0.0–500.0 ms Modulation delay time
Feedback gain (plus values for
FB. GAIN –99 to +99% normal-phase feedback, minus
values for reverse-phase feedback)
WAVE Sine, Tri Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
Used in conjunction with TEMPO
NOTE *1
to determine FREQ.
*1.
■ REV+SYMPHO.
One input, two output reverb and symphonic effects in
parallel.
Parameter Range
REV TIME 0.3–99.0 s Reverb time
INI. DLY 0.0–500.0 ms Initial delay before reverb begins
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
DIFF. 0–10 Spread
DENSITY 0–100% Reverb density
Reverb and symphonic balance
REV/SYM 0–100% (0% = all reverb, 100% = all sym-
phonic)
THRU, 21.2 Hz–
HPF High-pass filter cutoff frequency
8.00 kHz
50.0 Hz–16.0 kHz,
LPF Low-pass filter cutoff frequency
THRU
FREQ. 0.05–40.00 Hz Modulation speed
DEPTH 0–100% Modulation depth
MOD. DLY 0.0–500.0 ms Modulation delay time
WAVE Sine, Tri Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
Used in conjunction with TEMPO
*1
NOTE
to determine FREQ.
*1.
■ REV→SYMPHO.
One input, two output reverb and symphonic effects in
series.
Description
Parameter
REV TIME
INI. DLY
HI. RATIO
DIFF.
DENSITY
REV.BAL
HPF
LPF
FREQ.
DEPTH
MOD. DLY
WAVE
SYNC
NOTE
*1.
■ REV→PAN
This is a 1-in/2-out series-connected reverb and auto-pan
effect.
Parameter
REV TIME
Description
INI. DLY
HI. RATIO
DIFF.
DENSITY
REV.BAL
HPF
LPF
FREQ.
DEPTH
DIR.
WAVE
SYNC
NOTE
*1. L↔R, L→R, L←R, Turn L, Turn R
*2.
Effects Parameters
Range Description
0.3–99.0 s Reverb time
0.0–500.0 ms Initial delay before reverb begins
0.1–1.0 High-frequency reverb time ratio
0–10 Spread
0–100% Reverb density
Reverb and symphonic reverb bal-
0–100% ance (0% = all symphonic reverb,
100% = all reverb)
THRU, 21.2 Hz–
High-pass filter cutoff frequency
8.00 kHz
50.0 Hz–16.0 kHz,
Low-pass filter cutoff frequency
THRU
0.05–40.00 Hz Modulation speed
0–100% Modulation depth
0.0–500.0 ms Modulation delay time
Sine, Tri Modulation waveform
OFF/ON Tempo parameter sync on/off
Used in conjunction with TEMPO
*1
to determine FREQ.
Range Description
0.3–99.0 s Reverb time
0.0–500.0 ms Initial delay before reverb begins
0.1–1.0 High-frequency reverb time ratio
0–10 Spread
0–100% Reverb density
Reverb and panned reverb bal-
0–100% ance (0% = all panned reverb,
100% = all reverb)
THRU, 21.2 Hz–
High-pass filter cutoff frequency
8.00 kHz
50.0 Hz–16.0 kHz,
Low-pass filter cutoff frequency
THRU
0.05–40.00 Hz Modulation speed
0–100% Modulation depth
*1
Panning direction
Sine, Tri, Square Modulation waveform
OFF/ON Tempo parameter sync on/off
Used in conjunction with TEMPO
*2
to determine FREQ.
M7CL Owner's Manual
259