Advertisement
Quick Links
Advertisement
Related Manuals for Soundoff Signal nFUSE
Summary of Contents for Soundoff Signal nFUSE
- Page 1 INSTALLATION INSTRUCTIONS nFUSE ECE LIGHTBAR ® nFUSE ECE Lightbar English ® 0000KP 0325 REV A...
- Page 2 • Improper use or installation may void warranty coverage. • To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com/tech-services/returns/. • If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 800- 338-7337 (press #4).
- Page 3 Control Harness / Breakout Box (BOB) ......14 - 15 Connection of Breakout Box to SoundOff Signal Sirens ......16 Siren Functions / Photo Sensor .
- Page 4 ECE Lightbar ® CONTENTS COMPONENT nFUSE ECE Lightbar built to your specifications ® OPTIONAL MOUNTING HARDWARE* OPTIONAL CONTROL EQUIPMENT Vehicle Specific Hook Kit / Hardware Breakout Box Breakout Box COMPONENTS LIN (Standard) CAN System Fixed Height Mounting Brackets w/ Hardware Qty.
- Page 5 ECE Lightbar ® TOP VIEW WITH COVERS ON REAR FRONT TOP VIEW WITH COVERS OFF REAR INBOARD LED MODULES ALLEY MODULES CORNER MODULES FRONT BOTTOM VIEW FRONT REAR *48" lightbar pictured 800-338-7337 | soundoffsignal.com nFUSE ECE Lightbar English ®...
- Page 6 ECE Lightbar ® FIXED HEIGHT BRACKETS AND HOOK MOUNTING (PURSUIT) 1. Attach the supplied screws to the mounting foot to 7. Tighten the hook bracket bolts, torque details below: secure the rubber pad as shown in Figure 3. Due to different vehicle construction and mounting 2.
- Page 7 ECE Lightbar ® HEADACHE RACK MOUNTING (PNFLBK02) Place the T-Slot bolts in the extrusion slots on the underside of the lightbar. Insert the ½” hex head bolt into the center hole of the bracket. Place the bracket on the T-Slot bolts and loosely secure with flat washers and nylon locking nuts.
- Page 8 FUNCTION DESCRIPTIONS Mode Select: The nFUSE Exterior Lightbar is equipped with 8 selectable pattern configuration modes. Default wire configuration has defined settings for 6 of the 8 modes. Default is mode 1 when no other mode select inputs are active. Mode 2 is in use when the input is activated.
- Page 9 ECE Lightbar ® ELECTRICAL INSTALLATION Power Cable: 1. Route lightbar power cables as close to vehicles power source (battery) as possible. 2. Install a fuse (customer supplied) to the end of the RED wire of the Lightbar Power Cable.
- Page 10 ECE Lightbar ® ELECTRICAL INSTALLATION (CONT.) FLASH PATTERNS *fpm=Flashes per Minute **fps=Flashes per Second SAE Com- California Title Name pliant Compliant 13 Compliant Color Sequence Timing Timing Timing Random 1 Variable Random 2 Variable Quint Alternating Quad 2 Variable...
- Page 11 ECE Lightbar ® ELECTRICAL INSTALLATION (CONT.) FLASH PATTERNS CONT. *fpm=Flashes per Minute **fps=Flashes per Second California Title 13 Name Compliant Compliant Color Sequence Compliant Timing Timing Timing SN33 Power Sway SN34 Evert SN35 Alternating Rapid Flash SN36 Swift Impact...
- Page 12 ECE Lightbar ® ELECTRICAL INSTALLATION (CONT.) FLASH PATTERNS *fpm=Flashes per Minute **fps=Flashes per Second California Title SAE Compli- Name Compliant 13 Compliant Color Sequence ant Timing Timing Timing DN15 Impact Dual #1/2 Variable DN16 Explosion Dual #1/2 Variable DC17...
- Page 13 ECE Lightbar ® ELECTRICAL INSTALLATION (CONT.) FLASH PATTERNS CONT. *fpm=Flashes per Minute **fps=Flashes per Second California Title 13 Name Compliant Compliant Color Sequence Compliant Timing Timing Timing DN54 Slow Runner Dual - Aura II #1/2 Alternating DN55 Super Slow Runner Dual - Aura...
- Page 14 ECE Lightbar ® ELECTRICAL INSTALLATION CONTINUED 2 Amp Fuse** ** For optional backlight modules only. There may be more than one set of wires for the backlighting module. In cases such as these, it is O.K. to splice the connections into the same fuse.
- Page 15 Black Ground CHANGED OVERALL LENGTH FROM 300mm xxxx Green/White LIN 2 - Software Configurable SYNC2 Pattern TO 400mm Green LIN 1 - nFUSE Lightbar Operation 8mm 2mm HALF STRIP Power 30mm Table 3 400 mm 5mm Wire Color Function Ground...
- Page 16 ECE Lightbar ® CONNECTION OF LIGHTBAR BREAKOUT BOX TO SOUNDOFF SIGNAL SIREN: Note: Requires PC configuration app to map siren control switches to lightbar functions. Plug one end of the RJ-45 cable into the corresponding jack on the siren amplifier..
- Page 17 ECE Lightbar ® SIREN FUNCTIONS "Color CERT chosen (if the color is SAE/ not populated, NONE Button Function Mods affected Flash it would be the next color Pattern listed)" Pushbutton 1 Left Arrow Inboards Amber→Color 1 Pushbutton 2 Scene Left Alley and Left Alley Scene White→nothing...
- Page 18 ECE Lightbar ® LIGHT MODULE LOCATIONS 42" Lightbar FCNR FINB1 FINB2 FINB3 FINB2 FINB1 FCNR ID12 ID13 ID14 ALLEY ID30 ID15 ALLEY ALS: ID60 ID16 ID29 ID28 ID27 ID26 ID18 ID17 RINB2 RINB3 RCNR RCNR RINB1 RINB2 RINB1 48" Lightbar...
- Page 19 ECE Lightbar ® LIGHT MODULE LOCATIONS (CONT.) 60" Lightbar FCNR FINB1 FINB2 FINB3 FINB4 FINB4 FINB3 FINB2 FINB1 FCNR ID10 ID11 ID12 ID13 ID14 ALS: ID60 ID15 ALLEY ALS ID:60 ALLEY ID30 ID16 ID29 ID28 ID27 ID26 ID25 ID20...
- Page 20 Improper use or installation may void warranty coverage. To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at soundoffsignal.com/tech-services/returns/. If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 800-338-7337 (press #4).
- Page 21 ECE Lightbar ® nFUSE® LIGHTBAR TROUBLESHOOTING Normal Operation Under Normal operation with ignition input powered, the breakout box will have the Green LED ON and the Red LED light will be ON whenever an input is active. GENERAL TROUBLESHOOTING Before further troubleshooting •...
- Page 22 NFUSE LB DRIVER BOARD (36"-72") PNSLBBL01 NFUSE LB BACKLIGHT W/ HARNESS PNSLBTDVD1 NFUSE LB DIVIDER PNSLBLS08(x) NFUSE LB 8 LED SINGLE CLR MOD (COLOR) PNSLBLD16(x) NFUSE LB 16 LED DUAL CLR MOD (COLOR) 800-338-7337 | soundoffsignal.com nFUSE ECE Lightbar English ®...
- Page 23 ECE Lightbar ® NOTES 800-338-7337 | soundoffsignal.com nFUSE ECE Lightbar English ® 0000KP 0325 REV A...
- Page 24 Shipping & Handling, labor and service fees are non-refundable. ROUTING WIRES IN THE DEPLOYMENT AREA OF YOUR AIR BAG. SoundOff Signal is not liable for any damage due to installation or REFER TO YOUR VEHICLE OWNER’S MANUAL FOR AIR BAG personal injury as a result of using SoundOff Signal product.
Need help?
Do you have a question about the nFUSE and is the answer not in the manual?
Questions and answers