Download Print this page

Soundoff Signal nFUSE Installation Instructions Manual page 15

Ece lightbar
Hide thumbs Also See for nFUSE:

Advertisement

nFUSE
ECE Lightbar
®
CONTROL HARNESS / BREAKOUT BOX (BOB)
Wire
Wire Color
Pin #
1
BLU/WHT
2
GRN/WHT
3
GRY
STT - Rear Turn - Le�
4
BLK
STT - Rear Turn - Right
5
LTGRN
6
BRN/WHT
7
PUR
8
WHT
9
BLK/WHT
10
GRY/WHT
11
PUR/WHT
12
PNK/WHT
13
BLU
14
GRN
15
YEL
16
ORG
17
RED
18
PNK
Warning with Cruise 1 behind
19
RED/WHT
20
BRN
21
YEL/WHT
22
ORG/WHT
23
RED/BLK
24
LTGRN/WHT
VSS Input for Speed 1 and 2
BREAKOUT BOX INSTRUCTIONS:
(LIN COMMUNICATION)
a) Securely snap in the 4-pin and 24-pin connectors.
b) Install a 3Amp Fuse (customer supplied) to the end of the Red
wire of the 4-pin connector harness.
c) Hook up power, ground, and LIN to the corresponding wire
on the 4-pin connector harness. (Table 2)
d) Refer to Table 1 for the input wire's default function.
5
e) Follow the label for the wire color to connect to a +10-32Vdc
source, which turns on that given light or lights.
f) Make sure your wire connections are secured and isolated
E
from any other wire.
4-PIN CONNECTOR HARNESS
5
E
Wire
D
Color
Pin
1
Black
2
Green/White
LIN 2 - Software Configurable SYNC2 Pattern
3
Green
4
Red
D
C
15
C
800-338-7337 | soundoffsignal.com
B
Wire Func�on
Cruise 1
Inboard 1, Corners & Alleys (Front and Rear)
Warning
STT - Tail
Disable
Disable
Unassigned
Low Power 1
Le� Arrow
Right Arrow
IGNITION
Warning
En�re Bar (Front and Rear)
Warning
Warning
En�re Bar (Front and Rear)
Warning
En�re Bar (Front and Rear)
Warning
En�re Bar (Front and Rear)
En�re Bar (Front and Rear)
Flashing
Scene
Le� Alley and Le� Alley Scene
Scene
Right Alley and Right Alley Scene
Takedown
Scene 1
4
4
Table 2
INSULATION: HDPE
4
Function
50 mm 5mm
Ground
LIN 1 - nFUSE Lightbar Operation
8mm 2mm HALF STRIP
Power
3
400 mm 5mm
HOUSING CONNECTOR:
JST P/N: PAP-05V-S
Mods affected
populated, it would be the
En�re Bar (Rear)
Inboard 2 (pair)
Inboard 2 (pair)
Inboard 2 (pair)
Le� Side Endcap
Right Side Endcap
-
all
Inboards (Rear)
Inboards (Rear)
-
En�re Bar (Front)
Takedown
Selected at Bar Crea�on
Selected at Bar Crea�on
-
NOTE: CAN channels are intended to operate on a stand-
along communication bus using a proprietary command set.
a) Securely snap in the 4-pin, 5-pin and 24-pin connectors.
b) Install a 3Amp Fuse (customer supplied) to the end of the
Red wire of the 4-pin connector harness. (Table 2)
c) Hook up power, ground, and LIN to the corresponding wire
3
on the 4-pin connector harness.
d) Follow the label for the wire color to connect to a 10-32 Vdc
source, which turns on that given light or lights.
e) Refer to Table 1 for the input wire default functions.
f) Connect the CAN interface wires to an external CAN
controller per Table 3.
g) Make sure your wire connections are secured and isolated
from any other wire.
h) If extending the 5-pin connector harness, a shielding wire
running the length of the entire harness may be necessary.
Wire
2
Pin
1
2
3
4
5
NOTES:
1. CAD DATA IS MASTER
2. VOLUME = $PRPSHEET:{VOLUME MM} mm³
3. BREAK ALL SHARP EDGES, NO BURRS ALLOWED
Color
(→: If the color is not
Flash
next color listed)
Color 1, not White
-
Color 1
Mode 2
Amber→nothing
-
Amber→nothing
-
Red→nothing
-
-
-
-
-
-
-
-
-
Amber→Color 1
-
Amber→Color 1
-
-
-
Color 1
Mode 1
Color 1
Mode 2
Color 1
Mode 3
Color 1
Mode 4
Color 1
Mode 5
Color 1
Mode 6
White→nothing
-
White→nothing
-
White→nothing
-
White
-
White
-
-
-
CAN BREAKOUT BOX INSTRUCTIONS:
(CAN COMMUNICATION)
REV
1
3
REV
A
CONNECTOR PRESENT WITH CAN BOB
B
1
30mm
Table 3
Color
Function
Ground
CAN Low
NOTES:
Green
CAN Low
MECHANICAL CHARACTERISTICS(@ 1MHz)
CAN High
CONDUCTORS 20-22 AWG STRANDED BARE COPPER
5
TEMPURATURE RANGE -30 TO 65C
Yellow
CAN High
INSULATION: HDPE
LAST USED
CONSTRUCTION: SHIELDED TWISTED PAIR
INDUSTRY APPROVAL: SAE J1128
ELECTRICAL CHARACTERISTICS(@1MHz)
CHARACTERISTIC INDEPENDANCE 108-132 Ohms
CAPACITENCE CONNNECTOR TO CONDUCTOR <75p
CAPACITANCE CONDUCTOR TO SHIELD: <110pF/ m
2. TESTING:
- VERIFY END TO END CONTINUITY AND NO SHORT
CIRCUITS BETWEEN PINS
Table 1
CERT chosen
SAE/None
ECE
Pa�ern
-
-
Slow Runner
ECE Single
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Flicker Cruise
ECE Single
Slow Runner
ECE Single
Quint
ECE Single
Intercycle
ECE Single
Warp
ECE Single
Super Slow Runner
ECE Single
-
-
-
-
-
-
-
-
-
-
-
-
2
REVISION LOG
DESCRIPTION
INITIALS
2
REVISION LOG
DESCRIPTION
INITIALS
RELEASE FOR
GRP
PRODUCTION
CHANGED OVERALL
LENGTH FROM 300mm
GRP
TO 400mm
1
5
CAN CONNECTOR
CHARACTERISTIC NUMBERS
DELETED
nFUSE
ECE Lightbar English
®
0000KP 0325 REV A
PROPRIETARY AND CONFID
THE INFORMATION CONTA
THIS DRAWING IS THE SOLE
PROPERTY OF SOUNDOFF
ANY REPRODUCTION IN PA
®
1
ECN
01
1
ECN
5710
xxxx
K

Advertisement

loading
Need help?

Need help?

Do you have a question about the nFUSE and is the answer not in the manual?