Download Print this page

Soundoff Signal nFUSE Installation Instructions Manual page 20

Ece lightbar
Hide thumbs Also See for nFUSE:

Advertisement

nFUSE
ECE Lightbar
®
Inboard, Corner, and Alley Module Replacement:
1. Remove relevant top cover(s) by removing screws.
2. Disconnect the harness of the module in question from the
driver board.
3. Remove the entire light module.
4. Replacement modules should be connected to the nFUSE/
nFORCE Connector port on the AutoDim / Mod ID module.
5. Once the module is connected, the LED's under the 10's and
1's labels on the AutoDim / Mod ID module will flash Green
to indicate to the module's ID number.
EXAMPLE:
An ID of 20 will flash only the 10's LED
twice. Similarly an ID of 2 will flash only the 1's LED
twice. An ID of 15 would flash the 10's LED once then
the 1's LED 5 times.
6. To configure a new ID, quick press the 10's button to add 10 to the current ID and/or press the 1's button to add 1 to the current ID.
Pressing and holding the 10's or 1's button until the corresponding red LED goes off will subtract 10 or 1 respectively. Pressing and
holding both the 10's and 1's buttons at the same time and releasing once the red LED's turn off will change the ID to 1.
7. Once the 10's or 1's buttons have been pressed the LED's on the AutoDim / Mod ID module will change from green to red and flash
the potential new ID. If the ID flashes correctly press the SET button and it will configure the module to that ID. The LED's on the Au-
toDim / Mod ID module will now flash the module's new ID in green. If the new module ID flashes in green correctly then the module
is ready to be connected to the bar.
EXAMPLE:
If your module started out with ID 15 and the desired ID was 30 you would press the 10's button once and the
1's button 5 times(15 + 15 = 30.) Verify the 10's LED flashes red 3 times(indicating ID 30) then press the SET button. After
the SET button is pressed the 10's LED should flash green 3 times.
NOTE: The highest available ID is 60. Going past 60 will start back at 1 and going backwards from 1 will go to 60.
Power Distribution / Driver Module Replacement:
1. Verify power has been removed from Lightbar before attempting service.
2. Remove relevant top cover by removing screws.
3. Disconnect all wire harness connectors attached to the board.
4. Remove power distribution / driver module sensor board.
5. Snap new distribution/photo sensor board assembly into housing.
6. Reconnect all wire harnesses in the identical locations.
7. Apply power to Lightbar and verify proper operation.
AutoDim / Mod ID Module Replacement:
1. Verify power has been removed from Lightbar, before attempting service.
2. Remove driver side end cover by removing screws.
3. Disconnect wire harness attached to the board.
4. Remove the two screws.
5. Remove the module.
6. Install new module using the two screws.
7. Reconnect the wire harness to the identical connector.
8. Apply power to Lightbar and verify proper operation.
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at soundoffsignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 800-338-7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundoffsignal.com.
20
800-338-7337 | soundoffsignal.com
BOARD ASSEMBLY REPLACEMENT
Improper use or installation may void warranty coverage.
E N H A N C I N G S A F E T Y T H R O U G H I N N OVAT I O N
NOTICE:
Fuse
Connectors
F1
J1
F2
J2
F3
J3
F4
J4
F5
J5
F6
J6
nFUSE
ECE Lightbar English
®
0000KP 0325 REV A

Advertisement

loading
Need help?

Need help?

Do you have a question about the nFUSE and is the answer not in the manual?

Subscribe to Our Youtube Channel