Roland XV-5050 Owner's Manual page 98

Chapter 4 Using the XV-5050 Effects
81: GTR MULTI A (Guitar Multi A)
fig.02-081m
L in
Compressor
R in
Delay
Parameter Value
Compressor
Switch OFF, ON
Attack 0-127
Sustain 0-127
Level # 0-127
OD/Dist
Switch OFF, ON
Type OVERDRIVE,
DISTORTION
Drive # 0-127
Tone 0-127
Level 0-127
Amp Simulator
Switch OFF, ON
Type SMALL,
BUILT-IN,
2-STACK,
3-STACK
Delay
Switch OFF, ON
Time L 0-3000 ms,
note *2
Time R
Feedback -98-+98 %
HF Damp 200-8000 Hz,
BYPASS
Balance # D100:0W-
D0:100W
Cho/Flg
Switch OFF, ON
Type CHORUS,
FLANGER
Rate 0.05-10.00 Hz,
note *2
Depth 0-127
Feedback -98-+98 %
PreDly 0.0-100.0 ms
Filter Type OFF, LPF,
HPF
Cutoff Freq 200-8000 Hz
Balance # D100:0W-
D0:100W
Output
Level 0-127
Pan L64-63R
98
Overdrive/
Amp
Distortion
Simulator
L out
Chorus/
Pan
Flanger
R out
Description
Turns the Compressor on/off.
Sets the speed at which compression starts
Adjusts the duration of the compression.
Volume of the Compressor sound
Turns the Overdrive/Distortion on/off.
Selects either Overdrive or Distortion.
Amount of distortion
Also changes the volume.
Sound quality of the Overdrive/Distortion
effect
Volume of the Overdrive/Distortion
sound
Turns the Amp Simulator on/off.
Type of guitar amp
SMALL: small amp
BUILT-IN: single-unit type amp
2-STACK: large double stack amp
3-STACK: large triple stack amp
Turns the Delay on/off.
Adjusts the time until the delay is heard.
Adjusts the amount of the delay sound
that's fed back into the effect. Negative (-)
settings invert the phase.
Adjusts the frequency above which sound
fed back to the effect is filtered out. If you
don't want to filter out any high frequen-
cies, set this parameter to BYPASS.
Volume balance between the direct sound
(D) and the delay sound (W)
Turns the Chorus/Flanger on/off.
Selects either Chorus or Flanger.
Frequency of modulation
Depth of modulation
Adjusts the amount of the flanger sound
that's fed back into the effect. Negative (-)
settings invert the phase.
Adjusts the time until the chorus/flanger
is heard.
Type of filter
OFF: no filter is used
LPF: cuts the frequency range above the
Cutoff Freq
HPF: cuts the frequency range below the
Cutoff Freq
Basic frequency of the filter
Volume balance between the direct sound
(D) and the chorus/flanger sound (W)
Output level
Stereo location of the output
82: GTR MULTI B (Guitar Multi B)
fig.02-082m
L in
Compressor
R in
Chorus/
3-Band EQ
Flanger
Parameter Value
Compressor
Switch OFF, ON
Attack 0-127
Sustain 0-127
Level # 0-127
OD/Dist
Switch OFF, ON
Type OVERDRIVE,
DISTORTION
Drive # 0-127
Tone 0-127
Level 0-127
Amp Simulator
Switch OFF, ON
Type SMALL,
BUILT-IN,
2-STACK,
3-STACK
3 Band EQ
Switch OFF, ON
Low Gain -15-+15 dB
Mid Freq 200-8000 Hz
Mid Gain -15-+15 dB
Mid Q 0.5, 1.0, 2.0,
4.0, 8.0
High Gain -15-+15 dB
Cho/Flg
Switch OFF, ON
Type CHORUS,
FLANGER
Rate 0.05-10.00 Hz,
note *2
Depth 0-127
Feedback -98-+98 %
PreDly 0.0-100.0 ms
Filter Type OFF, LPF,
HPF
Cutoff Freq 200-8000 Hz
Balance # D100:0W-
D0:100W
Output
Level 0-127
Pan L64-63R
Overdrive/
Amp
Distortion
Simulator
L out
R out
Description
Turns the Compressor on/off.
Sets the speed at which compression starts
Adjusts the duration of the compression.
Volume of the Compressor sound
Turns the Overdrive/Distortion on/off.
Selects either Overdrive or Distortion.
Degree of distortion
Also changes the volume.
Sound quality of the Overdrive/Distortion
effect
Volume of the Overdrive/Distortion
sound
Turns the Amp Simulator on/off.
Type of guitar amp
SMALL: small amp
BUILT-IN: single-unit type amp
2-STACK: large double stack amp
3-STACK: large triple stack amp
Turns the 3 Band EQ on/off.
Gain of the low frequency range
Frequency of the middle frequency range
Gain of the middle frequency range
Width of the middle frequency range
Set a higher value for Q to narrow the fre-
quency range to be affected.
Gain of the high frequency range
Turns the Chorus/Flanger on/off.
Selects either Chorus or Flanger.
Frequency of modulation
Depth of modulation
Adjusts the amount of the flanger sound
that's fed back into the effect. Negative (-)
settings invert the phase.
Adjusts the time until the chorus/flanger
is heard.
Type of filter
OFF: no filter is used
LPF: cuts the frequency range above the
Cutoff Freq
HPF: cuts the frequency range below the
Cutoff Freq
Basic frequency of the filter
Volume balance between the direct sound
(D) and the chorus/flanger sound (W)
Output level
Stereo location of the output