Roland XV-5050 Owner's Manual page 95

74: RHODES MULTI
L in
Enhancer
Mix
R in
Enhancer
Mix
Chorus/
Flanger
Feedback
Chorus/
Flanger
Parameter Value
Enhancer
Switch OFF, ON
Sens # 0-127
Mix 0-127
Phaser
Switch OFF, ON
Mode 4-STAGE, 8-STAGE
Manual # 0-127
Rate # 0.05-10.00 Hz, note *2
Depth 0-127
Resonance 0-127
Mix 0-127
Cho/Flg
Switch OFF, ON
Type CHORUS, FLANGER
Rate 0.05-10.00 Hz, note *2
Depth 0-127
Feedback -98-+98 %
Pre Dly 0.0-100.0 ms
Filter Type OFF, LPF, HPF
Cutoff Freq 200-8000 Hz
Balance # D100:0W-D0:100W
Tre/Pan
Switch OFF, ON
Type TREMOLO, AUTO
PAN
Mod Wave TRI, SQR, SIN, SAW1,
SAW2
SAW1
(R)
(L)
Rate # 0.05-10.00 Hz, note *2
Depth # 0-127
Output
Level 0-127
Resonance
Phaser
Mix
Tremolo/
L out
Pan
Tremolo/
R out
Pan
Description
Turns the Enhancer on/off.
Sensitivity of the enhancer
Level of the overtones generated by
the enhancer
Turns the Phaser on/off.
Number of stages in the phaser
Adjusts the basic frequency from
which the sound is modulated.
Frequency of modulation
Depth of modulation
Amount of feedback
Level of the phase-shifted sound
Turns the Chorus/Flanger on/off.
Selects either Chorus or Flanger.
Frequency of modulation
Depth of modulation
Adjusts the amount of the flanger
sound that is fed back into the effect.
Negative (-) settings invert the
phase.
Adjusts the time until the chorus/
flanger is heard.
Type of filter
OFF: no filter is used
LPF: cuts the frequency range
above the Cutoff Freq
HPF: cuts the frequency range
below the Cutoff Freq
Basic frequency of the filter
Volume balance between the direct
sound (D) and the chorus/flanger
sound (W)
Turns Tremolo/Pan on/off.
Selects either Tremolo or Pan.
Modulation Wave
TRI: triangle wave
SQR: square wave
SIN: sine wave
SAW1/2: sawtooth wave
SAW2
(R)
(L)
Frequency of modulation
Depth of modulation
Output level
Chapter 4 Using the XV-5050 Effects
75: JD MULTI
This allows the Distortion (DS), Phaser (PH), Spectrum (SP), and
Enhancer (EH) effects to be connected in series in any desired order.
fig.02-075m
L in
Distortion
R in
Spectrum
Parameter Value
Sequence DS-PH-SP-EN
:
EN-SP-PH-DS
Dist
Switch OFF, ON
Type MELLOW DRIVE,
OVERDRIVE,
CRY DRIVE,
MELLOW DIST,
LIGHT DIST,
FAT DIST,
FUZZ DIST
Drive # 0-100
Level 0-100
Phaser
Switch OFF, ON
Manual # 50 Hz-15.0 kHz
Rate # 0.1-10.0 Hz
Depth # 0-100
Resonance # 0-100
Mix Level # 0-100
Spectrum
Switch OFF, ON
Band1 (250Hz) -15-+15 dB
Band2 (500Hz)
Band3 (1000Hz)
Band4 (2000Hz)
Band5 (4000Hz)
Band6 (8000Hz)
Width 1, 2, 3, 4, 5
Enhancer
Switch OFF, ON
Sens 0-100
Mix Level # 0-100
Output
Level 0-127
Pan L64-63R
Phaser
L out
Enhancer
R out
Description
Order in which effects are con-
nected
Turns the Distortion on/off.
Type of distortion
MELLOW DRIVE: A soft, mel-
low distortion; somewhat dark
sounding.
OVERDRIVE: The classic sound
of an overdriven tube amp.
CRY DRIVE: Distortion with a
high-frequency boost.
MELLOW DIST: Sounds like the
distortion you'd get from a really
big amp.
LIGHT DIST: A distortion with
an intense, brilliant feel.
FAT DIST: Boosted lows and
highs gives this one a thick, fat
sound.
FUZZ DIST: Like FAT DIST, but
with even more distortion.
Amount of distortion
Distortion output level
Turns the Phaser on/off.
Adjusts the basic frequency
from which the sound is mod-
ulated.
Frequency of modulation
Depth of modulation
Amount of feedback
Level of the phase-shifted
sound
Turns the Spectrum on/off.
Gain of each frequency band
Simultaneously adjusts the
width of all frequency bands.
Turns the Enhancer on/off.
Sensitivity of the enhancer
Level of the overtones generat-
ed by the enhancer
Output level
Stereo location of the output
95