Roland XV-5050 Owner's Manual page 92

Chapter 4 Using the XV-5050 Effects
65: St AUTO WAH (Stereo Auto Wah)
fig.02-065m
L in
Auto Wah 2-Band EQ
R in
Auto Wah
2-Band EQ
Parameter Value
Filter Type LPF, BPF
Sens # 0-127
Manual # 0-127
Peak 0-127
Rate # 0.05-10.00 Hz,
note *2
Depth # 0-127
Polarity UP, DOWN
Phase # 0-180 deg
Low Gain -15-+15 dB
High Gain -15-+15 dB
Level 0-127
66: ST FORMN FLT
L in
Overdrive Formant
R in
Overdrive Formant
Parameter Value
Drive Sw OFF, ON
Drive # 0-127
Vowel 1 a, e, i, o, u
Vowel 2
Rate # 0.05-10.00 Hz,
note *2
Depth # 0-127
Manual # 0-100
Phase # 0-180 deg
Keysync Sw OFF, ON
Keysync Thresh 0-127
Low Gain -15-+15 dB
High Gain -15-+15 dB
Level 0-127
92
L out
R out
Description
Type of filter
LPF: The wah effect is applied over a
wide frequency range.
BPF: The wah effect is applied over a nar-
row frequency range.
Adjusts the sensitivity with which the fil-
ter is controlled.
Adjusts the center frequency at which the
effect is applied.
Adjusts the amount of the wah effect that
occurs in the center frequency range.
Set a higher value for Q to narrow the af-
fect range.
Frequency of modulation
Depth of modulation
Sets the direction in which the frequency
changes when the auto-wah filter is modu-
lated.
UP: The filter changes toward a higher
frequency.
DOWN: The filter changes toward a lower
frequency.
Adjusts the degree of phase shift of the left
and right sounds when the wah effect is
applied.
Gain of the low frequency range
Gain of the high frequency range
Output level
(Stereo Formant Filter)
L out
2-Band EQ
R out
2-Band EQ
Description
Turns Drive on/off.
Degree of distortion
Also changes the volume.
Selects the vowel.
Frequency at which the two vowels
switch
Effect depth
Adjusts the point at which the two
vowels switch.
When set to 50, Vowels 1 and 2
switch in the same amount of time.
Setting this lower than 50 increases
the time for Vowel 1; setting this
higher than 50 decreases the time
for Vowel 1.
Adjusts the phase shift of the left
and right sounds when the two vow-
els are switched.
Determines whether the LFO for
switching the vowels is reset accord-
ing to the input sound (ON) or not
(OFF).
Volume level at which reset is ap-
plied
Gain of the low frequency range
Gain of the high frequency range
Output level
67: MLT TAP DLY2 (Multi Tap Delay 2)
This allows you to achieve longer delay times (max. 3000 ms) for the
Multi-Tap Delay function.
fig.02-067m
L in
Delay 1
Feed
back
Delay 3
Multi Tap Delay
Delay 4
Delay 2
R in
Parameter Value
Delay 1-4 0-3000 ms,
note *2
Feedback # -98-+98 %
HF Damp 200-8000 Hz,
BYPASS
Delay Level 1-4 0-127
Delay Pan 1-4 L64-63R
Low Gain -15-+15 dB
High Gain -15-+15 dB
Balance # D100:0W-
D0:100W
Level 0-127
68: REVERSE DLY2 (Reverse Delay 2)
This allows you to achieve longer delay times (max. 1500 ms) for the
Reverse Delay function.
fig.02-068m
L in
D1
Rev. Delay
Feedback 1
Feedback 4
R in
Parameter Value
Delay 1-4 0-1500 ms,
note *2
Feedback 1 # -98-+98 %
Feedback 4 #
HF Damp 1 200-8000
Hz, BYPASS
HF Damp 4
Delay Level 1-3 0-127
Delay Pan 1-3 L64-63R
Threshold 0-127
Low Gain -15-+15 dB
High Gain -15-+15 dB
Balance # D100:0W-
D0:100W
Level 0-127
Balance D
2-Band
L out
EQ
Balance W
Balance W
2-Band
R out
EQ
Balance D
Description
Adjusts the time until Delay 1-4s are
heard.
Adjusts the amount of the delay sound
that's fed back into the effect. Negative
(-) settings invert the phase.
Adjusts the frequency above which
sound fed back to the effect is filtered
out. If you don't want to filter out any
high frequencies, set this parameter to
BYPASS.
Output level of Delays 1-4
Stereo location of Delays 1-4
Gain of the low frequency range
Gain of the high frequency range
Volume balance between the direct
sound (D) and the effect sound (W)
Output level
2-Band
EQ
1
D2
Delay
2
D3
D4
3
2-Band
EQ
Description
Adjusts the time until Delays 1-4 are
heard.
Adjusts the amount of the delay sound
that's fed back into the effect. Negative
(-) settings invert the phase.
Adjusts the frequency above which
sound fed back to the effect is filtered
out. If you don't want to filter out any
high frequencies, set this parameter to
BYPASS.
Output level of Delays 1-3
Stereo location of Delays 1-3
Volume level at which the reverse de-
lay begins
Gain of the low frequency range
Gain of the high frequency range
Volume balance between the direct
sound (D) and the effect sound (W)
Output level
L out
R out