Roland XV-5050 Owner's Manual page 85

40: CHO/FLANGER
The parameters are the same as for "37: CHO -> FLANGER."
However, the Flanger Balance parameter adjusts the volume balance
between the direct sound and the flanger sound.
fig.02-040m
Balance D
L in
Chorus
Feedback
Flanger
R in
Balance D
41: St PHASER (Stereo Phaser)
This is a stereo phaser. With the Step effects, you can also make
stepped changes in the pitch of sounds to which the Phaser effect is
applied.
fig.02-041m
L in
Phaser
Mix
Mix
Phaser
R in
Parameter Value
Type 1, 2
Mode 4-STAGE,
8-STAGE
Polarity INVERSE,
SYNCHRO
Manual # 0-127
Rate # 0.05-10.00 Hz,
note *2
Depth 0-127
Resonance 0-127
X-Feedback -98-+98 %
Mix 0-127
Step Switch OFF, ON
Step Rate # 0.10-20.00 Hz,
note *2
Low Gain -15-+15 dB
High Gain -15-+15 dB
Level 0-127
L out
Balance W
Balance W
R out
2-Band
L out
EQ
2-Band
R out
EQ
Description
Type of phaser
Type 2 adds more of the phaser effect
to the high frequencies than Type 1.
Number of stages in the phaser
Selects whether the left and right
phase of the modulation are the same
or opposite each other.
INVERSE: The left and right phase are
opposite. When using a mono source, this
spreads the sound in stereo.
SYNCHRO: The left and right phase are
the same. Select this when working with a
stereo source.
Adjusts the basic frequency from
which the sound is modulated.
Frequency of modulation
Depth of modulation
Amount of feedback
Adjusts the amount of the phaser
sound that's fed back into the effect.
Negative (-) settings invert the phase.
Level of the phase-shifted sound
Determines whether the pitch is
changed in a stepped fashion (ON) or
not (OFF).
Rate (period) of pitch change
Gain of the low frequency range
Gain of the high frequency range
Output level
Chapter 4 Using the XV-5050 Effects
42: KEYSYNC FLG (Keysync Flanger)
This effect controls the Flanger by resetting the effect at the volume
of the sound sent into to the effect, restarting from the same pitch
each time the Flanger is reset.
This parameter lets your playing dynamics on the keyboard control
the flanger effect.
fig.02-042m
L in
Flanger
Feedback
Feedback
Flanger
R in
Parameter Value
LFO Rate # 0.05-10.00 Hz,
note *2
LFO Depth 0-127
Feedback # -98-+98 %
Phase 0-180 deg
Pre Delay 0.0-100 ms
Filter Type OFF, LPF, HPF
Cutoff Freq 200-8000 Hz
Step Sw OFF, ON
Step Rate # 0.10-20.00 Hz,
note *2
Keysync OFF, ON
Threshold 0-127
Ksync Phase 0-360 deg
Low Gain -15-+15 dB
High Gain -15-+15 dB
Balance # D100:0W-
D0:100W
Level 0-127
2-Band
L out
EQ
2-Band
R out
EQ
Description
Frequency of modulation
Depth of modulation
Adjusts the amount of the flanger
sound that's fed back into the effect.
Negative (-) settings invert the
phase.
Spatial spread of the sound
Adjusts the time until the flanger is
heard.
Type of filter
OFF: no filter is used
LPF: cuts the frequency range above
the Cutoff Freq
HPF: cuts the frequency range below
the Cutoff Freq
Basic frequency of the filter
Determines whether the pitch is
changed in a stepped fashion (ON)
or not (OFF).
Rate (period) of pitch change
Determines whether the Flanger
LFO is reset by the input signal (ON)
or not (OFF).
Adjusts the volume level at which
the reset is applied.
LFO phase when the LFO is reset
Gain of the low frequency range
Gain of the high frequency range
Volume balance between the direct
sound (D) and the flanger sound (W)
Output level
85