Roland XV-5050 Owner's Manual page 96

Chapter 4 Using the XV-5050 Effects
76: St LOFI COMP
This is a stereo Lo-Fi compressor. It deliberately degrades the sound
quality for creative effect.
fig.02-076m
L in
Lo-Fi 2-Band EQ
R in
Lo-Fi 2-Band EQ
Parameter Value
LoFi Type 1-9
Pre Filter 1-6
Post Filter 1 1-6
Post Filter 2 OFF, LPF, HPF
Post Cutoff 200-8000 Hz
Low Gain -15-+15 dB
High Gain -15-+15 dB
Balance # D100:0W-
D0:100W
Level 0-127
96
(Stereo Lo-Fi Compress)
L out
R out
Description
Degrades the sound quality.
The sound quality grows
poorer as this value is in-
creased.
Adjusts the type of filter ap-
plied to the sound before it
passes through the Lo-Fi ef-
fect.
Adjusts the type of filter ap-
plied to the sound after it
passes through the Lo-Fi ef-
fect.
Type of filter
OFF: no filter is used
LPF: cuts the frequency range
above the Cutoff
HPF: cuts the frequency range
below the Cutoff
Basic frequency of the filter
Gain of the low frequency
range
Gain of the high frequency
range
Volume balance between the
direct sound (D) and the ef-
fect sound (W)
Output level
77: St LOFI NOIZ (Stereo Lo-Fi Noise)
This is a stereo Lo-Fi noise. In addition to a Lo-Fi effect, this effect
also generates various types of noise such as radio noise and disc
noise.
fig.02-077m
L in
Lo-Fi
Radio Noise Gen.
Lo-Fi
R in
Parameter Value
LoFi Type 1-9
Post Filter OFF, LPF,
HPF
Cutoff Freq 200-8000 Hz
Hum N Type 50 Hz, 60 Hz
Hum N LPF 200-8000 Hz,
BYPASS
Hum N Level 0-127
Radio Detune # 0-127
RadioNoise Level 0-127
W/P Noise Type WHITE, PINK
W/P LPF 200-8000 Hz,
BYPASS
White/Pink Level 0-127
Disc N Type LP, EP, SP,
RND
Disc N LPF 200-8000 Hz,
BYPASS
Disc N Level 0-127
Low Gain -15-+15 dB
High Gain -15-+15 dB
Balance # D100:0W-
D0:100W
Level 0-127
2-Band
L out
EQ
2-Band
R out
EQ
Description
Degrades the sound quality. The
sound quality grows poorer as this
value is increased.
Type of filter
OFF: no filter is used
LPF: cuts the frequency range above
the Cutoff
HPF: cuts the frequency range below
the Cutoff
Basic frequency of the filter
Type of hum noise
Adjusts the cutoff frequency of the
low pass filter applied to the hum
noise. If you don't want to filter
out any high frequencies, set this
parameter to BYPASS.
Volume of the hum noise
Simulates the tuning noise of a ra-
dio.
As this value is raised, the tuning
drifts further.
Volume of the radio noise
Selects either white noise or pink
noise.
Adjusts the cutoff frequency of the
low pass filter applied to the white
noise or pink noise. If you don't
want to filter out any high frequen-
cies, set this parameter to BYPASS.
Volume of the white noise or pink
noise
Type of record noise
The frequency at which the noise is
heard depends on the selected type.
Adjusts the cutoff frequency of the
low pass filter applied to the
record noise. If you don't want to
filter out any high frequencies, set
this parameter to BYPASS.
Volume of the record noise
Gain of the low frequency range
Gain of the high frequency range
Volume balance between the direct
sound (D) and the effect sound (W)
Output level