Roland XV-5050 Owner's Manual page 52

Chapter 1 Creating a Patch
Parameter
Rx MIDI Redamper Tone Redamper Switch
Env Mode Tone Envelope Mode
TMT CONTROL
TMT Control SW
Bend Range Down Pitch Bend Range Down
Bend Range Up Pitch Bend Range Up
MATRIX CTRL
This selects the parameters to be controlled by Matrix Control Source 1–4 and the Sens settings, as well as the specific Tones whose parameters you wish to control. Up
to four destination parameters can be selected for each controller and controlled simultaneously.
Ctrl 1–4 Src Matrix Control 1–4 Source
Ctl1–4 Dest1–4 Matrix Control 1–4 Destina-
tion 1–4
Ctl1–4 Sens1–4 Matrix Control 1–4 Sens 1–4
Ctl1–4 Switch1–4 Matrix Control 1–4 Tone Con-
trol Switch 1–4
52
Value Description
OFF, ON If a Hold 1 message is received during the time between a note-off—
when you release the key—and the time at which the note actually
disappears, any currently sounding notes will be sustained if Re-
damper is set to ON. To take advantage of this feature, you must also
turn on the Tone Receive Hold 1 setting.
NO-SUS, SUSTAIN When a loop-type waveform is selected, it normally continues to
sound as long as a key is pressed. If you want a note to decay natu-
rally even when the key remains pressed, set this to "NO-SUS."
* If a one-shot type Wave is selected, it will not sustain even if this
OFF, ON This setting determines whether or not the TMT is controlled by the Ma-
trix Control. When TMT Velocity Control is set to OFF, turning this pa-
rameter on and off is a simple way to switch between playing all Tones or
controlling them with the Matrix Control, making this an effective tool for
auditioning Tones.
-48–0 Specifies the amount of pitch change that's applied to the Patch's pitch
when the Pitch Bend lever is moved fully left (or down on some MIDI con-
trollers).
0–48 Specifies the pitch change that occurs when the Pitch Bend lever is moved
fully to the right (or up on some MIDI controllers).
OFF, CC01–31, CC33–95, Assign one of the following controllers to Control Source 1–4. If you wish
BEND, AFTER, SYS1–4, VE- to use a controller that will apply to all Patches, or a controller that cannot
LOCITY, KEYFOLLOW, be directly selected here, select SYS-CTRL1–4, and then select the control-
TEMPO, LFO1, LFO2, PIT- ler using the Control Source 1–4 parameters (SYSTEM: CONTROL).
ENV, TVF-ENV, TVA-ENV
OFF, PCH, CUT, RES, LEV, Selects a parameter to be controlled.
PAN, DRY, CHO, REV,
PIT-LFO1(2), TVF-LFO1(2),
TVA-LFO1(2), PAN-LFO1(2),
LFO1(2)-RATE, PIT-ATK,
PIT-DCY, PIT-REL,
TVF-ATK, TVF-DCY,
TVF-REL, TVA-ATK,
TVA-DCY, TVA-REL, TMT,
FXM, MFX-CTRL1–4
-63–+63 Adjusts the amount of change that occurs in response to controller chang-
es. Negative (-) values invert the change. For LFO rates, negative (-) values
slow down the LFO, and positive (+) values speed it up.
OFF, ON, REVERSE Selects the Tone to which the two previous parameter settings are
applied. "ON" turns signifies that the Tone is selected for control,
"OFF" that it's not selected, and "REVERSE" that the change being
applied is inverted when applied to this Tone.
parameter is set to "SUSTAIN."
T
T
T