Progress Tone And Ring Configuration; Distinctive Ring And Other Ring Settings - Cisco Linksys RT31P2 Administration Manual

4.9.

Progress Tone and Ring Configuration

The progress tones and ring tones on the PHONE ADAPTER are extremely configurable. There are
18 configurable call progress tones, 8 configurable ringing cadences, and 8 configurable call waiting
cadences. Progress tones and Ring cadences are configured using FreqScipts and CadScripts
respectively (described in Section 4.1).
4.9.1.

Distinctive Ring and Other Ring Settings

Distinctive Ringing and Distinctive Call Waiting Tones can be associated with specific callers
configured directly into the PHONE ADPATER, by setting the appropriate callers in the Ring_n_Caller
parameters. The Ring_1_Caller parameter specifies which callers will trigger ring cadence 1, and so
forth. If a provider wishes to offer a distinctive ringing service by providing hints from the network, the
provider can insert an Alert-Info SIP header into incoming calls. If the value in the Alert-Info header
matches one of the strings in the Ring_n_Name set of parameters, the corresponding ring cadence
will be used.
In addition to ordinary and distinctive rings, there are number of other situations where the PHONE
ADAPTER can provide a short burst of ringing. These ring settings are described below.
Parameter Name
Ring 1 Caller
Ring 2 Caller
Ring 3 Caller
Ring 4 Caller
Ring 5 Caller
Ring 6 Caller
Ring 7 Caller
Ring 8 Caller
Default Ring
Default CWT
Hold Reminder Ring
Call Back Ring
Ring1 Name
Ring2 Name
Ring3 Name
Ring4 Name
Ring5 Name
Ring6 Name
Ring7 Name
© 2004 Linksys Proprietary (See Copyright Notice on Page 2)
Description
Caller number pattern to play Distinctive Ring/CWT 1
Caller number pattern to play Distinctive Ring/CWT 2
Caller number pattern to play Distinctive Ring/CWT 3
Caller number pattern to play Distinctive Ring/CWT 4
Caller number pattern to play Distinctive Ring/CWT 5
Caller number pattern to play Distinctive Ring/CWT 6
Caller number pattern to play Distinctive Ring/CWT 7
Caller number pattern to play Distinctive Ring/CWT 8
Default ringing pattern, 1 – 8, for all callers
Default CWT pattern, 1 – 8, for all callers
Ring pattern for reminder of a holding call when the
phone is on-hook
Ring pattern for call back notification
Name in an INVITE's Alert-Info Header to pick
distinctive ring/CWT 1 for the inbound call
Name in an INVITE's Alert-Info Header to pick
distinctive ring/CWT 2 for the inbound call
Name in an INVITE's Alert-Info Header to pick
distinctive ring/CWT 3 for the inbound call
Name in an INVITE's Alert-Info Header to pick
distinctive ring/CWT 4 for the inbound call
Name in an INVITE's Alert-Info Header to pick
distinctive ring/CWT 5 for the inbound call
Name in an INVITE's Alert-Info Header to pick
distinctive ring/CWT 6 for the inbound call
Name in an INVITE's Alert-Info Header to pick
distinctive ring/CWT 7 for the inbound call
Type Default
PhTmplt
PhTmplt
PhTmplt
PhTmplt
PhTmplt
PhTmplt
PhTmplt
PhTmplt
{1,2,3,4, 1
5,6,7,8}
{1,2,3,4, 1
5,6,7,8}
{1,2,3,4, None
5,6,7,8,
None}
{1,2,3,4, None
5,6,7,8}
Str31 Bellcore-r1
Str31 Bellcore-r2
Str31 Bellcore-r3
Str31 Bellcore-r4
Str31 Bellcore-r5
Str31 Bellcore-r6
Str31 Bellcore-r7
67