Related Manuals for Gira 2399 02
Summary of Contents for Gira 2399 02
- Page 1 Operating instructions Presence detector and motion detector 360° compact Order no. 2399 02 Product image non-binding...
-
Page 2: Table Of Contents
Presence detector and motion detector 360° compact Table of contents Safety instructions ...................... 3 Battery safety instructions .................... 3 Device components ...................... 4 Intended use ........................ 4 Operation .......................... 7 Information for electrically skilled persons .............. 10 Mounting and electrical connection.............. 11 Commissioning .................... -
Page 3: Safety Instructions
Presence detector and motion detector 360° compact Safety instructions Electrical devices may be mounted and connected only by electrically skilled persons. Serious injuries, fire or property damage are possible. Please read and follow the manual fully. Danger of electric shock. Device is not suitable for disconnection from supply voltage because mains potential even is applied on the load when the device is switched off. -
Page 4: Device Components
Presence detector and motion detector 360° compact Device components Figure 1 Connection box Sensor cover Brightness sensor Sensor window with red and blue display LED Decor ring Push-on cover Figure 2 IR PIR 2 remote control, included in the scope of delivery IR PIR 1 remote control (installation engineer), see Accessories Intended use –... - Page 5 Presence detector and motion detector 360° compact – Indoor ceiling mounting, surface-mounted Product characteristics – 2-point light control – Functions settable with IR remote controls – Restriction of the detection field by switching off individual sensors or push-on cover – Operation with IR remote control, 2-wire extension or push-button –...
- Page 6 Presence detector and motion detector 360° compact Switch-off warning If the switch-off warning is active, the light is not switched off immediately after the run-on time has elapsed. Triple flashing at an interval of 10 seconds shows that the light will be switched off soon. The run-on time is thereby prolonged by approx. 30 seconds.
-
Page 7: Operation
Presence detector and motion detector 360° compact Operation Special functions can be switched and settings adjusted using the supplied PIR 2 IR remote control. Special functions can restrict operation via the 2-wire extensions or push-but- tons. If multiple devices are within the range of the IR remote control, then align it so that only the device to be operated can receive the signals. - Page 8 Presence detector and motion detector 360° compact Ų In the next 10 seconds, the brightness Pressing for less than 10 seconds threshold can be changed incrementally using the Ű or ű buttons. Ų Saving the current ambient brightness as Pressing for longer than 10 seconds the brightness threshold Set 2 Activate settings that have been saved...
- Page 9 Presence detector and motion detector 360° compact Switch on the light for 2 hours Motions are not evaluated during this time. It is not possible to switch off via a 2-wire extension or push-button. ￭ Press 2 h on button of the IR remote control. Light is switched on for 2 hours.
-
Page 10: Information For Electrically Skilled Persons
Presence detector and motion detector 360° compact Each button press extends or shortens the brightness threshold by 10% of the set value, but by at least 1 lux. Saving the current brightness as the switch-on brightness ￭ Press the Ų button for longer than 10 seconds. The current brightness is saved as the switch-on brightness. -
Page 11: Mounting And Electrical Connection
Presence detector and motion detector 360° compact Mounting and electrical connection Detection field and range Figure 3: Tangential and radial direction of motion The device has a detection field of 360°. The diameter of the detection field depends on the installation height and the direction of motion of persons in the detection field (see figure 4). - Page 12 Presence detector and motion detector 360° compact Installation height 3.00 m 20.00 m 16.00 m 12.00 m 8.00 m 3.50 m 23.00 m 18.50 m 14.00 m 9.00 m 4.00 m 26.00 m 17.00 m 14.50 m *) – *) 5.00 m 28.00 m 18.00 m...
- Page 13 Presence detector and motion detector 360° compact Figure 5: Detection field areas A, B and C, installation height 2.50 m Figure 6: Arrangement of the areas A, B and C ￭ Align the connection box (1) in such a way that the areas A, B and C match the structural conditions.
- Page 14 Presence detector and motion detector 360° compact Preparations for mounting Figure 7: Mounting Connection box Sensor cover Decor ring Fastening pins (10) Screws ￭ Pull off decor ring (5) (see figure 7). ￭ Loosen screws (10) (see figure 7). Installing the connection box Figure 8: Connection box (11) Fastening holes...
- Page 15 Presence detector and motion detector 360° compact ￭ For an additional flush-mounted cable entry or surface-mounted cable entry, break out the appropriate thin point (13) (see figure 8). ￭ Fastening the connection box (1) through holes (11) (see figure 8). Alternatively, the device can also be mounted on a 60 mm appliance box.
- Page 16 Presence detector and motion detector 360° compact Connection assignment black, BK, L Phase conductor brown, BR, ↓ Switched phase conductor blue, BU, N Neutral conductor grey, GY, 1 Connection push-button Protective conductor ￭ Connect optional push-button (14) (see figure 9) or (see figure 10). This is only necessary if manual operation is also desired.
-
Page 17: Commissioning
Presence detector and motion detector 360° compact Area I cut out Ø approx. 7.5 m Areas I + II cut out Ø approx. 12 m without push-on cover Ø approx. 20 m ￭ Pull off push-on cover. ￭ Using scissors, cut out push-on cover along the marked lines as required. ￭... - Page 18 Presence detector and motion detector 360° compact ū Switching on the Motion detector device Pressing for longer than 10 seconds function Ŭ No function is saved for this device Test 100 h Switch on test operation Pressing for less than 10 seconds Test 100 h On for 100 hours Pressing for longer than 10 seconds...
- Page 19 Presence detector and motion detector 360° compact If all the PIR sensors are switched off, then the device functions as a twilight switch. Individual PIR sensors or all of them can be switched on by setting a sensitiv- ity for the PIR sensors (see Setting sensitivity). Setting the switch-on brightness One of four predefined brightness thresholds (see table) or one individual brightness threshold can be set (see Saving current brightness as the switch-on brightness).
- Page 20 Presence detector and motion detector 360° compact Setting individual run-on time The individual run-on time can be set within a range of 10 seconds to 60 minutes. One of the fixed run-on times can be set again at any time. ￭...
- Page 21 Presence detector and motion detector 360° compact If day operation is set as the switch-on brightness, the light remains off con- tinuously. Switching via a 2-wire extension or push-button is not possible. Switch on test operation The test operation is used for testing the detection area. In test operation, the device operates independently of the brightness.
-
Page 22: Technical Data
Presence detector and motion detector 360° compact Sensitivity of PIR A-C Detection angle 360°, PIR A-C switched on Switch-on brightness 10 lux Run-on time 2 minutes Dynamic run-on time switched-off Short-time operation switched-off Switch-off warning switched-off Presence simulation switched-off Test operation switched-off If the Reset button is pressed for between 4 and 10 seconds, only a few func- tions are terminated (see Button assignment of "installation engineer"... -
Page 23: Troubleshooting
Presence detector and motion detector 360° compact Inductive transformers 1000 VA HV-LED lamps typ. 400 W Compact fluorescent lamps typ. 400 W Fluorescent lamps, uncompensated 920 VA Capacitive load 690 VA (560 μF) Connected load at AC 110 V~ and 35 °C Incandescent lamps 1150 W HV halogen lamps... - Page 24 Presence detector and motion detector 360° compact Device switches on without motions Cause 1: Presence simulation is activated. Device switches at saved times. Switch the presence simulation off. Cause 2: Interference sources in the detection field. Remove interference sources if possible. Reduce sensitivity.
-
Page 25: Accessories
Please submit or send faulty devices postage paid together with a fault de- scription to your responsible salesperson (specialist trade / installation company / electrical specialist trade). They will forward the devices to the Gira Service Center. Gira Giersiepen GmbH & Co. KG...