Advertisement
Quick Links
Presence detector and motion detector 360° compact
Presence detector and motion detector 360° compact
Order No. : 2399 02
Operating instructions
1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled persons.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
Danger of electric shock. Device is not suitable for disconnection from supply voltage.
Danger of electric shock. Always disconnect before carrying out work on the devise or
load. In so doing, take all the circuit breakers into account, which support dangerous
voltages to the device and or load.
Do not press on the sensor window. Device can be damaged.
Keep button cells out of reach of children! If button cells are swallowed, get medical help
immediately.
Risk of explosion! Do not throw batteries into fire.
Risk of explosion! Do not recharge batteries.
The device is not suitable for use as a burglar alarm or other alarm.
These instructions are an integral part of the product, and must remain with the end
customer.
2 Device components
Figure 1
(1) Connection box
(2) Sensor top
(3) Brightness sensor
(4) Sensor window with red and blue display LED
(5) Decor ring
(6) Push-on cover
82593212
12.01.2017
1/18
Advertisement
Related Manuals for Gira 2399 02
Summary of Contents for Gira 2399 02
- Page 1 Presence detector and motion detector 360° compact Presence detector and motion detector 360° compact Order No. : 2399 02 Operating instructions 1 Safety instructions Electrical devices may only be mounted and connected by electrically skilled persons. Serious injuries, fire or property damage possible. Please read and follow manual fully.
- Page 2 Presence detector and motion detector 360° compact Figure 2 (7) IR PIR 2 remote control (end customer), included in the scope of delivery (8) IR PIR 1 remote control (installation engineer), see Accessories 3 Function Intended use Automatic switching of lighting depending on the heat motion and ambient brightness. Indoor ceiling mounting, surface-mounted Product characteristics 2-point light control...
- Page 3 Presence detector and motion detector 360° compact To avoid any switch-on caused by a cooling illuminant, no movement signals are evaluated for a brief lockout time after switching off. The motion detector adjusts itself to the ambient conditions to keep the time as short as possible. Short time operation If movement occurs, then a short pulse of approx.
- Page 4 Presence detector and motion detector 360° compact Light switched on continuously Light switched off continuously or twilight button function activated Flashing slowly Presence simulation switched Flashing Receipt of IR signals Flashing IR signal detected Button assignment of the end user IR remote control Button Function ů...
- Page 5 Presence detector and motion detector 360° compact Press the top or full-surface of the 2-wire extension or installation button for less than 0.4 seconds. Light is switched on depending on brightness and motion. Movements are evaluated according to the brightness and prolong the run-on time. Switching the light off for a period of 3 minutes i This function can only be used in presence detector operation.
- Page 6 Presence detector and motion detector 360° compact Saving the current brightness as the switch-on brightness Press the Ų button for longer than 10 seconds. The current brightness is saved as the switch-on brightness. Adjusting the run-on time The run-on time is set during commissioning. The run-on time can be adjusted at a later time using the supplied IR remote control.
- Page 7 Presence detector and motion detector 360° compact The device has a detection area of 360°. The diameter of the detection area depends on the installation height and the direction of motions of persons in the detection area (Figure 4). The detection area becomes larger the greater the installation height, while the detection density and sensitivity are reduced at the same time.
- Page 8 Presence detector and motion detector 360° compact i The detection area can be limited in order to minimize the influence of interference sources. For this, use the push-on cover (see Limiting the detection area with the push-on cover) or switch off individual sensors (see Limiting the detection area). Aligning the device The device has three independent PIR sensors for motion detection(Figure 5).
- Page 9 Presence detector and motion detector 360° compact Preparations for installation Figure 7: Fitting (1) Connection box (2) Sensor top (5) Decor ring (9) Fastening pins (10) Screws Pull off the decor ring (5) (Figure 7). Loosen the screws (10) (Figure 7). Installing the connection box Figure 8: Connection box (11) Fastening holes...
- Page 10 Presence detector and motion detector 360° compact Align the device (for the position of areas A, B, C, see Aligning the device) - the brightness sensor should, if possible, be located on the side away from the window. This reduces the effects of scattered light.
- Page 11 Presence detector and motion detector 360° compact Connect the sensor top according to the connection diagram (Figure 9) or switch the sensor tops according to the circuit diagram (Figure 10). If multiple miniature circuit breakers supply dangerous voltages to the device or load, couple the miniature circuit breakers or label them with a warning, to ensure disconnection is guaranteed.
- Page 12 Presence detector and motion detector 360° compact Using scissors, cut out push-on cover along the marked lines as required. Push on push-on cover. i Alternatively, the detection area can also be limited by switching off individual sensors (see Commissioning). 5.2 Commissioning Insert battery into IR remote control i To avoid contact problems, keep the contacts of batteries and device free of grease.
- Page 13 Presence detector and motion detector 360° compact ŭ Switch on/off switch-off warning Pressing for longer than 10 seconds Prog Func No function is saved for this device Reset Switching off the functions: Dynamic run-on Actuation of between 4 seconds and time, switch-off prewarning, on for 100 hours, 10 seconds test operation...
- Page 14 Presence detector and motion detector 360° compact Saving the current brightness as the switch-on brightness The Teach function can be used to save the current brightness as a switch-on brightness. i Do not shade the device during the measuring process. Create the desired lighting situation, e.g.
- Page 15 Presence detector and motion detector 360° compact Switch on test operation The test operation is used for testing the detection area. In test operation, the device operates independently of the brightness. All the other settings remain unchanged. Detected motions are signalled by the blue status LED.
- Page 16 Presence detector and motion detector 360° compact Remove empty batteries immediately and dispose of in an environmentally friendly manner. Do not throw batteries into household waste. Consult your local authorities about environmentally friendly disposal. According to statutory provisions, the end consumer is obligated to return used batteries.
- Page 17 The warranty follows about the specialty store in between the legal framework as provided for by law Please submit or send faulty devices postage paid together with an error description to your responsible salesperson (specialist trade/installation company/electrical specialist trade). They will forward the devices to the Gira Service Center. 82593212 12.01.2017 17/18...
- Page 18 Presence detector and motion detector 360° compact Gira Giersiepen GmbH & Co. KG Elektro-Installations- Systeme Industriegebiet Mermbach Dahlienstraße 42477 Radevormwald Postfach 12 20 42461 Radevormwald Deutschland Tel +49(0)21 95 - 602-0 Fax +49(0)21 95 - 602-191 www.gira.de info@gira.de 82593212 12.01.2017...