Enabling And Disabling The Parksense Active Park Assist System - RAM 1500 2025 Owner's Manual

E A D T
NABLING ND ISABLING HE
A P A S
CTIVE ARK SSIST YSTEM
The ParkSense Active Park Assist system
can be enabled and disabled with the
ParkSense Active Park Assist switch, located
on the right-hand side of the Uconnect
screen faceplate.
To enable the ParkSense Active Park Assist system,
push the ParkSense Active Park Assist switch once (LED
turns on). Pushing the switch a second time will disable
the system (LED turns off).
The ParkSense Active Park Assist system will turn off
automatically for any of the following conditions:
●
Parking maneuver is completed
●
Vehicle speed is greater than 28 mph (45 km/h)
when searching for a parking space during a Fully
Automated maneuver
●
Vehicle speed is greater than 18 mph (30 km/h)
when searching for a parking space during a Semi-
Automatic maneuver
●
Vehicle speed is greater than 5 mph (7 km/h) during
Semi-Automatic active steering guidance into the
parking space
●
Steering wheel is touched during Fully Automated
or Semi-Automatic active steering guidance into the
parking space
●
The gas pedal or brake pedal is pressed during Fully
Automated active steering guidance into the parking
space
●
ParkSense Front and Rear Park Assist switch is
pushed
●
P S
Any of the doors are opened during a Fully
ARK ENSE
Automated maneuver
●
The driver door is opened during a Semi-Automatic
maneuver
●
Tailgate is opened
●
A trailer is connected
●
Vehicle is in 4WD Low
●
Cruise Control, Adaptive Cruise Control, or Active
Driving Assist systems are engaged
●
Electronic Stability Control/Anti-Lock Braking System
intervention
The ParkSense Active Park Assist system allows
a maximum number of shifts between DRIVE and
REVERSE. If the maneuver cannot be completed within
the maximum amount of shifts, the system will cancel
and the instrument cluster display will instruct the
driver to complete the maneuver manually.
The ParkSense Active Park Assist system will only
operate and search for a parking space when the
following conditions are present:
●
Gear selector is in DRIVE
●
Ignition is in the RUN position
●
ParkSense Active Park Assist switch is activated
●
All of the doors are closed
●
Tailgate is closed
●
Vehicle speed is less than 15 mph (25 km/h) during
a Semi-Automatic maneuver
●
Vehicle speed is less than 25 mph (40 km/h) during
a Fully Automated maneuver
STARTING AND OPERATING
●
The outer surface and the underside of the front and
rear fascias/bumpers are clean and clear of snow,
ice, mud, dirt or other obstructions.
NOTE:
●
During a Semi-Automatic maneuver, if the vehicle
is driven above approximately 15 mph (25 km/h),
the instrument cluster display will instruct the
driver to slow down. If the vehicle is driven above
approximately 18 mph (30 km/h), the system will
cancel. The driver must then reactivate the system
by pushing the ParkSense Active Park Assist switch.
●
During a Fully Automated maneuver, if the vehicle
is driven above approximately 25 mph (40 km/h),
the instrument cluster display will instruct the
driver to slow down. If the vehicle is driven above
approximately 28 mph (45 km/h), the system will
cancel. The driver must then reactivate the system
by pushing the ParkSense Active Park Assist switch.
When pushed, the LED on the ParkSense Active Park
Assist switch will blink momentarily. If any of the
previously described conditions are not present, then
the LED will turn off.
When the ParkSense Active Park Assist system is
enabled, you can select between Park or Exit in the
Uconnect system. From there, you can select a parallel
or perpendicular maneuver.
If the vehicle is in any other gear than DRIVE, and an
objected is detected in the vehicle's path, the system
will default to Parallel Park Exit. A prompt will appear in
the Uconnect display, and the driver will need to select
"Yes" or "No" for a Parallel Park Exit maneuver. Any
other conditions will result in a default to a Parallel
Parking maneuver.
159
4