Download Print this page

RAM 3500 2018 Owner's Manual

RAM 3500 2018 Owner's Manual

Hide thumbs Also See for 3500 2018:

Quick reference manual (25 pages)

,

Quick start manual

Table of Contents

Advertisement

Quick Links

R A M T R U C K

2 0 1 8

1 5 0 0 / 2 5 0 0 / 3 5 0 0

O W N E R ' S M A N U A L

Table of Contents

Advertisement

Chapters

Table of Contents

Need help?

Need help?

Do you have a question about the 3500 2018 and is the answer not in the manual?

Questions and answers

Summary of Contents for RAM 3500 2018

Page 1 R A M T R U C K 2 0 1 8 1 5 0 0 / 2 5 0 0 / 3 5 0 0 O W N E R ’ S M A N U A L...
Page 2 VEHICLES SOLD IN CANADA This manual illustrates and describes the operation of With respect to any Vehicles Sold in Canada, the name features and equipment that are either standard or op- FCA US LLC shall be deemed to be deleted and the name tional on this vehicle.
Page 3 TABLE OF CONTENTS SECTION PAGE INTRODUCTION ..............3 GRAPHICAL TABLE OF CONTENTS .
Page 5: Table Of Contents
INTRODUCTION CONTENTS INTRODUCTION ......4 WARNINGS AND CAUTIONS ....7 HOW TO USE THIS MANUAL .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assis- tance of service and engineering specialists to acquaint you Dear Customer, congratulations on selecting your new with the operation and maintenance of your vehicle. It is vehicle. Be assured that it represents precision workman- supplemented by Warranty Information, and customer ship, distinctive styling, and high quality.
Page 7: How To Use This Manual
INTRODUCTION HOW TO USE THIS MANUAL described for technical and/or commercial reasons. For further information, contact an authorized dealer. Essential Information If applicable, refer to the owners manual supplement for Consult the Table of Contents to determine which section related information. contains the information you desire.
Page 8: Symbols
6 INTRODUCTION Symbols Consult the following table for a description of the symbols that may be used on your vehicle or throughout this Owner’s Manual:...
Page 9: Warnings And Cautions
INTRODUCTION WARNINGS AND CAUTIONS Operating instructions for the special equipment installed by the conversion/camper manufacturer should also be This Owner’s Manual contains WARNINGS against oper- supplied with your vehicle. If these instructions are miss- ating procedures that could result in a collision, bodily ing, please contact your authorized dealer for assistance in injury and/or death.
Page 11 GRAPHICAL TABLE OF CONTENTS CONTENTS FRONT VIEW ......10 INSTRUMENT PANEL .....12 REAR VIEW.
Page 12: Front View
10 GRAPHICAL TABLE OF CONTENTS FRONT VIEW Front View 1 — Hood/Engine Compartment 4 — Wheels/Tires 2 — Windshield 5 — Doors 3 — Headlights 6 — Exterior Mirrors...
Page 13: Rear View
GRAPHICAL TABLE OF CONTENTS 11 REAR VIEW Rear View 1 — Rear Lights 2 — Tailgate...
Page 14: Instrument Panel
12 GRAPHICAL TABLE OF CONTENTS INSTRUMENT PANEL Instrument Panel 1 — Air Vents 4 — Instrument Cluster 2 — Multifunction Lever 5 — Gear Selector 3 — Steering Wheel 6 — Radio...
Page 15: Interior
GRAPHICAL TABLE OF CONTENTS 13 INTERIOR Interior 1 — Door Locks/Window Switches 4 — Radio Controls 2 — Seats 5 — Storage Compartment 3 — Gear Selector...
Page 17 GETTING TO KNOW YOUR VEHICLE CONTENTS KEYS ....... . .20 ▫...
Page 18 16 GETTING TO KNOW YOUR VEHICLE ▫ Automatic Door Locks — If Equipped ..42 ▫ Rear Head Restraint Removal ....60 ▫...
Page 19: Windshield
GETTING TO KNOW YOUR VEHICLE 17 ▫ Tilt Side Mirrors In Reverse — If Equipped ..71 ▫ Turn Signals ......78 ▫...
Page 20 18 GETTING TO KNOW YOUR VEHICLE ▫ Operating Tips ......104 ▫ Opening ......113 WINDOWS .
Page 21 GETTING TO KNOW YOUR VEHICLE 19 ▫ Auxiliary Switches — If Equipped ..138 ▫ Camper Applications ....152 PICKUP BOX .
Page 22: Keys
20 GETTING TO KNOW YOUR VEHICLE KEYS NOTE: When using the emergency key to gain access to your vehicle, be aware that the security alarm may be Key Fobs triggered. Insert the key into the ignition and place the Your vehicle uses either a wireless ignition node system or ignition in the ON/RUN mode to disarm the security keyless ignition system.
Page 23 GETTING TO KNOW YOUR VEHICLE 21 The fourth position is START, during start RUN will illuminate. It also contains the key fob and an emergency key, which stores in the rear of the key fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the key fob go dead.
Page 24 22 GETTING TO KNOW YOUR VEHICLE NOTE: Inserting the key fob with integrated key into the ignition switch disables the system from responding to any button pushes from that key fob. Driving at speeds 5 mph (8 km/h) and above disables the system from responding to all key fob buttons for all key fobs.
Page 25 GETTING TO KNOW YOUR VEHICLE 23 To Lock The Doors And Tailgate Using The Panic Alarm Push and release the lock button on the key fob to lock all To turn the Panic Alarm feature on or off, push the Panic doors, the tailgate and the RamBox (if equipped).
Page 26 24 GETTING TO KNOW YOUR VEHICLE Air Suspension (Remote Lowering Of The Vehicle) Canceling Remote Lowering — If Equipped Vehicle lowering can be cancelled at anytime. When vehicle lowering is canceled, the vehicle will raise up to the next For easy entry and loading, your vehicle can be defined level and lock out the remote lowering feature lowered by pushing the key fob air suspension until the ignition has been cycled ON/OFF.
Page 27 GETTING TO KNOW YOUR VEHICLE 25 1. Remove the emergency key by sliding the mechanical latch on the back of the key fob sideways with your thumb and then pull the key out with your other hand. Emergency Key Removal Emergency WIN Key Removal...
Page 28 26 GETTING TO KNOW YOUR VEHICLE 2. Separating key fob halves requires screw removal – if equipped, and gently prying the two halves of the key fob apart. Make sure not to damage the seal during removal. Separating WIN Key Fob Case Remove Screw From Key Fob Case...
Page 29: Ignition Switch
GETTING TO KNOW YOUR VEHICLE 27 Programming Additional Key Fobs Programming the key fob may be performed by an autho- rized dealer. General Information The following regulatory statement applies to all radio frequency (RF) devices equipped in this vehicle: This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s).
Page 30 28 GETTING TO KNOW YOUR VEHICLE detents and one that is spring-loaded. The detent positions Removing Key Fob From The (WIN) Ignition are OFF, ACC, and ON/RUN. The START position is a Place the gear selector in PARK (if equipped with an spring-loaded momentary contact position.
Page 31 GETTING TO KNOW YOUR VEHICLE 29 WARNING! (Continued) WARNING! (Continued) • Do not leave children or animals inside parked into REVERSE, apply the parking brake, turn the vehicles in hot weather. Interior heat build-up may vehicle OFF, remove the key fobs from the vehicle, and lock all doors.
Page 32: Keyless Push Button Ignition - If Equipped
30 GETTING TO KNOW YOUR VEHICLE Keyless Push Button Ignition — If Equipped This feature allows the driver to operate the ignition switch with the push of a button as long as the Remote Keyless Entry key fob is in the passenger compartment. The Keyless Push Button Ignition has four operating positions;...
Page 33: Remote Start - If Equipped
GETTING TO KNOW YOUR VEHICLE 31 NOTE: • Fuel meets minimum requirement • Keyed Ignition systems will chime in OFF or ACC • System not disabled from previous remote start event when the driver door is open. • Vehicle security alarm not active •...
Page 34: To Enter Remote Start Mode
32 GETTING TO KNOW YOUR VEHICLE • Remote Start Disabled — Start Vehicle to Reset • The engine can be started two consecutive times (two 15-minute cycles) with the key fob. However, the igni- The instrument cluster display message stays active until tion must be placed in the ON/RUN position before you the ignition is turned to the ON/RUN position.
Page 35: General Information
GETTING TO KNOW YOUR VEHICLE 33 SENTRY KEY activated. These features will stay on through the duration of Remote Start or until the ignition switch is placed in the The Sentry Key Immobilizer System prevents unauthor- ON/RUN mode. ized vehicle operation by disabling the engine. The system does not need to be armed or activated.
Page 36: Customer Key Programming
34 GETTING TO KNOW YOUR VEHICLE Replacement Keys an invalid key fob to try to start the engine. Either of these conditions will result in the engine being shut off after two NOTE: Only key fobs that are programmed to the vehicle seconds.
Page 37: General Information
GETTING TO KNOW YOUR VEHICLE 35 General Information For an additional 15 minutes only, the headlights will turn on, the park lamps and/or turn signals, and vehicle The following regulatory statement applies to all radio security light will flash. frequency (RF) devices equipped in this vehicle: To Arm The System This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s).
Page 38: To Disarm The System
36 GETTING TO KNOW YOUR VEHICLE exterior zone (refer to Keyless Enter- N-Go — Passive 3. Cycle the ignition out of the OFF position. Entry in Getting To Know Your Vehicle for further • For vehicles equipped with Keyless Enter-N-Go — information).
Page 39: Rearming Of The System
GETTING TO KNOW YOUR VEHICLE 37 Rearming Of The System The vehicle security alarm will rearm itself after the 15 additional minutes of headlights and vehicle security light flashing, if the system has not been disabled. If the condi- tion which initiated the alarm is still present, the system will ignore that condition and monitor the remaining doors and ignition.
Page 40: Power Door Locks - If Equipped
38 GETTING TO KNOW YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • For personal security and safety in the event of an ignition of a vehicle equipped with Keyless Enter- collision, lock the vehicle doors as you drive as well N-Go in the ACC or ON/RUN mode. A child could as when you park and leave the vehicle.
Page 41: Keyless Enter-N-Go - Passive Entry
GETTING TO KNOW YOUR VEHICLE 39 Enter-N-Go. This feature allows you to lock and unlock the vehicle’s door(s) without having to push the key fob lock or unlock buttons. NOTE: • Passive Entry may be programmed ON/OFF. Refer to “Uconnect Settings” in “Multimedia” for further infor- mation.
Page 42 40 GETTING TO KNOW YOUR VEHICLE To Unlock From The Driver’s Side: To Unlock From The Passenger Side: With a valid Passive Entry key fob within 5 ft (1.5 m) of the With a valid Passive Entry key fob within 5 ft (1.5 m) of the driver door handle, grab the front driver door handle to passenger door handle, grab the front passenger door unlock the driver’s door automatically.
Page 43 GETTING TO KNOW YOUR VEHICLE 41 automatically unlocks all vehicle doors and chirps the horn three times (on the third attempt ALL doors will lock and the Passive Entry key fob can be locked in the vehicle). To Lock The Vehicle’s Doors: With one of the vehicle’s Passive Entry key fobs within 5 ft (1.5 m) of the driver or passenger front door handles, push the door handle lock button to lock all doors.
Page 44: Automatic Door Locks - If Equipped
42 GETTING TO KNOW YOUR VEHICLE The vehicle doors can also be locked by using the key fob authorized dealer per written request of the customer. lock button or the lock button located on the vehicle’s Please see your authorized dealer for service. interior door panel.
Page 45: Child-Protection Door Lock
GETTING TO KNOW YOUR VEHICLE 43 Child-Protection Door Lock To provide a safer environment for children riding in the rear seat, the rear doors (if equipped) of your vehicle have the Child-Protection Door Lock system. Child Lock Control WARNING! Avoid trapping anyone in the vehicle in a collision. Remember that the sliding doors cannot be opened Child-Protection Door Lock Location from the inside door handle when the Child Protection...
Page 46: Seats
44 GETTING TO KNOW YOUR VEHICLE Manual Front Seat Adjustment NOTE: • After setting the Child-Protection Door Lock system, Manual Front Seat Forward/Rearward Adjustment always test the door from the inside to make certain it is Both front seats are adjustable forward or rearward. The in the desired position.
Page 47 GETTING TO KNOW YOUR VEHICLE 45 WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked.
Page 48: Manual Rear Seat Adjustment
46 GETTING TO KNOW YOUR VEHICLE WARNING! (Continued) • To avoid injury, place your hand on the seatback and actuate the handle, then position the seatback in the desired position. 40-20-40 Front Bench Seat — If Equipped The seat is divided into three segments. The outboard seat portions are each 40% of the total width of the seat.
Page 49 GETTING TO KNOW YOUR VEHICLE 47 outboard side of the driver’s seat cushion. There are two Adjusting The Seat Up Or Down power seat switches that are used to control the movement The height of the seats can be adjusted up or down. Pull of the seat cushion and the seatback.
Page 50: Power Passenger Seat Adjustment - If Equipped
48 GETTING TO KNOW YOUR VEHICLE WARNING! (Continued) • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
Page 51: Driver Memory Seat - If Equipped
GETTING TO KNOW YOUR VEHICLE 49 Adjusting The Seat Up Or Down The memory seat buttons are located on the outboard side of the driver’s seat cushion. The height of the seats can be adjusted up or down. Pull upward or push downward on the rear of seat switch, the seat will move in the direction of the switch.
Page 52 50 GETTING TO KNOW YOUR VEHICLE • If your vehicle is not equipped with a touchscreen, you 3. Push and release the set (S) button on the memory switch. must select the “Key Fob Linked To Memory” feature through the instrument cluster display. Refer to “Instru- 4.
Page 53 GETTING TO KNOW YOUR VEHICLE 51 Memory Position Recall Driver Two Memory Position Recall • To recall the memory setting for driver two using the NOTE: memory switch, push memory button (2) on the • For vehicles equipped with an automatic transmission, memory switch.
Page 54: Heated Seats - If Equipped
52 GETTING TO KNOW YOUR VEHICLE Keyless Enter-N-Go), the driver’s seat will move about NOTE: The Easy Entry/Exit feature is not enabled when the 2.4 inches (60 mm) rearward if the driver’s seat position vehicle is delivered from the factory. The Easy Entry/Exit is greater than or equal to 2.7 inches (67.7 mm) forward feature is enabled (or later disabled) through the program- of the rear stop.
Page 55 GETTING TO KNOW YOUR VEHICLE 53 Front Heated Seats NOTE: The engine must be running for the heated seats to operate. The front heated seats control buttons are located on the center instrument panel below the climate controls. Vehicles Equipped With Remote Start If your vehicle is equipped with a touchscreen, the front On models that are equipped with remote start, the driv- heated seats control buttons are also located within the...
Page 56: Ventilated Seats - If Equipped
54 GETTING TO KNOW YOUR VEHICLE There are two heated seat switches that allow the rear of illuminated LEDs changes from two to one, indicating passengers to operate the seats independently. You can the change. The LO-level setting will turn OFF automati- choose from HI, LO or OFF heat settings.
Page 57: Manual Folding Rear Seats (Mega Cab Models)
GETTING TO KNOW YOUR VEHICLE 55 Manual Folding Rear Seats (Mega Cab Models) Vehicles Equipped With Remote Start On models that are equipped with remote start, the venti- Folding Rear Seat — Table Mode lated seats can be programmed to come on during a remote Both the left and right rear seat backs can be folded down start.
Page 58 56 GETTING TO KNOW YOUR VEHICLE 2. Fold the seat back forward. Manual Folding Rear Seat — Fold Flat Both the outboard rear seats will drop and move forward when the seat back is folded flat. WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle.
Page 59 GETTING TO KNOW YOUR VEHICLE 57 To fold either rear seat flat: 1. Lift the handle, located on the outboard side of either of the rear seats. Rear Passenger Fold-Flat Seats 3. Lift the seat back, to return the seat to the upright position.
Page 60: Plastic Grocery Bag Retainers (Regular Cab Models)
58 GETTING TO KNOW YOUR VEHICLE HEAD RESTRAINTS WARNING! Head restraints are designed to reduce the risk of injury by An improperly latched seat could cause serious injury restricting head movement in the event of a rear impact. or death. Make sure that the seatback is securely Head restraints should be adjusted so that the top of the locked into position.
Page 61: Rear Head Restraint Adjustment
GETTING TO KNOW YOUR VEHICLE 59 the head restraint. To lower the head restraint, push the adjustment button located on the base of the head restraint and push downward on the head restraint. Adjustment Buttons 1 — Release Button 2 — Adjustment Button Release/Adjustment Buttons NOTE: Do not reposition the head restraint 180 degrees to 1 —...
Page 62: Front Head Restraint Removal
60 GETTING TO KNOW YOUR VEHICLE • Do not reposition the head restraint 180 degrees to the Rear Head Restraint Removal incorrect position in an attempt to gain additional clear- To remove the head restraint, push the adjustment button ance to the back of the head. and the release button while pulling upward on the whole assembly.
Page 63: Steering Wheel
GETTING TO KNOW YOUR VEHICLE 61 STEERING WHEEL WARNING! Tilt Steering Column Do not adjust the steering column while driving. This feature allows you to tilt the steering column upward Adjusting the steering column while driving or driv- or downward. The tilt lever is located on the steering ing with the steering column unlocked, could cause the column, below the multifunction lever.
Page 64: Driver Adjustable Pedals - If Equipped
62 GETTING TO KNOW YOUR VEHICLE • Press the heated steering wheel button a second time WARNING! (Continued) to turn the heating element off. • Do not place anything on the steering wheel that NOTE: The engine must be running for the heated steering insulates against heat, such as a blanket or steering wheel to operate.
Page 65: Instrument Cluster
GETTING TO KNOW YOUR VEHICLE 63 NOTE: • Always adjust the pedals to a position that allows full pedal travel. • Further small adjustments may be necessary to find the best possible seat/pedal position. • For vehicles equipped with Driver Memory Seat, you can use your remote keyless entry key fob or the memory switch on the driver’s door trim panel to return the adjustable pedals to pre-programmed positions.
Page 66: Mirrors
64 GETTING TO KNOW YOUR VEHICLE CAUTION! Do not place any article under the adjustable pedals or impede its ability to move, as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjust- able pedal’s path.
Page 67: Automatic Dimming Mirror With Rear View Camera Display - If Equipped
GETTING TO KNOW YOUR VEHICLE 65 The Automatic Dimming feature can be turned on or off CAUTION! through the touchscreen. To avoid damage to the mirror during cleaning, never • Press the mirror dimmer button once to turn the feature on. spray any cleaning solution directly onto the mirror.
Page 68: Outside Mirrors
66 GETTING TO KNOW YOUR VEHICLE When the vehicle is placed into reverse gear, a video NOTE: If your vehicle is equipped with illuminated ap- display illuminates to display the image generated by the proach lights under the outside mirrors, they can be turned rear view camera located on the tailgate handle.
Page 69: Power Mirrors - If Equipped
GETTING TO KNOW YOUR VEHICLE 67 Power Mirrors — If Equipped The power mirror controls consist of mirror select buttons and a four-way mirror control switch. The controls for the power mirrors are located on the driver’s door trim panel. Power Mirror Controls Power Mirror Controls Location 1 —...
Page 70: Power Folding Outside Mirrors For Standard And Trailer Tow - If Equipped
68 GETTING TO KNOW YOUR VEHICLE To adjust a mirror, push either the L (left) or R (right) Push the switch once and the mirrors will fold in, push the button to select the mirror that you want to adjust. switch a second time and the mirrors will return to the normal driving position.
Page 71 GETTING TO KNOW YOUR VEHICLE 69 Resetting The Power Folding Outside Mirrors NOTE: • The power fold mirrors are designed to operate while You may need to reset the power folding mirrors if the the vehicle is stationary or traveling at moderate speeds. following occurs: If you attempt to power fold the mirrors at high speeds •...
Page 72: Trailer Towing Mirrors - If Equipped
70 GETTING TO KNOW YOUR VEHICLE Trailer Towing Mirrors — If Equipped Outside Mirrors Folding Feature All outside mirrors are designed to be able to be manually These mirrors are designed with an adjustable mirror head folded both forward and rearward to prevent damage. to provide a greater vision range when towing extra-wide loads.
Page 73: Heated Mirrors - If Equipped
GETTING TO KNOW YOUR VEHICLE 71 Tilt Side Mirrors In Reverse — If Equipped Tilt Side Mirrors In Reverse provides automatic outside mirror positioning which will aid the driver’s view of the ground rearward of the front doors. The outside mirrors will move slightly downward from the present position when the vehicle is shifted into REVERSE.
Page 74: Illuminated Vanity Mirror - If Equipped
72 GETTING TO KNOW YOUR VEHICLE Illuminated Vanity Mirror — If Equipped “Slide-On-Rod” Features Of Sun Visor — If Equipped Illuminated vanity mirrors are located on each sun visor. To use the mirror, rotate the sun visor down and swing the The sun visor “Slide-On-Rod”...
Page 75: Exterior Lights
GETTING TO KNOW YOUR VEHICLE 73 EXTERIOR LIGHTS Your vehicle is equipped with plastic headlight and fog light (if equipped) lenses that are lighter and less suscep- Headlight Switch tible to stone breakage than glass lights. Plastic is not as The headlight switch is located on the left side of the scratch resistant as glass and therefore different lens clean- instrument panel, next to the steering wheel.
Page 76: Headlights
74 GETTING TO KNOW YOUR VEHICLE Headlights Daytime Running Lights (DRL) — If Equipped To turn on the headlights, rotate the headlight switch The headlights on your vehicle will illuminate when the clockwise to the headlight position. When the headlight engine is started and the transmission is in any gear except switch is on, the parking lights, taillights, license plate light PARK.
Page 77: Automatic High Beam Headlamp Control - If
GETTING TO KNOW YOUR VEHICLE 75 NOTE: • The Automatic High Beam Headlamp Control can be turned on or off by selecting “ON” under “Auto High Beam” within your Uconnect settings, as well as turning the headlight switch to the AUTO position. Refer to “Uconnect Settings”...
Page 78: Flash-To-Pass
76 GETTING TO KNOW YOUR VEHICLE 3. Push the multifunction lever away from you (toward feature is also on. This means the headlights will stay on front of vehicle) to engage the high beam mode. for up to 90 seconds after you place the ignition into the OFF position.
Page 79: Parking Lights And Panel Lights
GETTING TO KNOW YOUR VEHICLE 77 Parking Lights And Panel Lights Headlight Delay To aid in your exit, your vehicle is equipped with a To turn on the parking lights and instrument panel headlight delay that will leave the headlights on for lights, rotate the headlight switch clockwise.
Page 80: Fog Lights - If Equipped
78 GETTING TO KNOW YOUR VEHICLE Fog Lights — If Equipped Turn Signals The fog lights are turned on by rotating the headlight Move the multifunction lever up or down and the arrows switch to the parking light or headlight position and on each side of the instrument cluster display will flash to pushing in the headlight rotary control.
Page 81: Lane Change Assist - If Equipped
GETTING TO KNOW YOUR VEHICLE 79 Lane Change Assist — If Equipped If the vehicle’s speed is 0 mph (0 km/h), these lights can also be turned on using the switch located just inside the Tap the lever up or down once, without moving beyond pickup box.
Page 82: Battery Saver
80 GETTING TO KNOW YOUR VEHICLE NOTE: Battery saver mode is canceled if the ignition is If the headlights remain on while the ignition is cycled OFF, the exterior lights will automatically turn off after eight minutes. If the headlights are turned on and left on for eight minutes while the ignition is OFF, the exterior lights will automatically turn off.
Page 83 GETTING TO KNOW YOUR VEHICLE 81 fob, if equipped. These lights are also operated individu- ally as reading lights by pushing on the corresponding lens. Rear Passenger Courtesy/Reading Light NOTE: The courtesy/reading lights will remain on until the switch is pushed a second time, so be sure they have been turned off before exitingthe vehicle.
Page 84 82 GETTING TO KNOW YOUR VEHICLE Ambient Light The overhead console is equipped with an ambient light feature. This light casts illumination for improved visibility of the floor console area. Dimmer Control “Party Mode” When a door is open and the interior lights are on, rotating the dimmer control all the way left, to the off detent, will Ambient Light cause all the interior lights to go out.
Page 85: Illuminated Approach
GETTING TO KNOW YOUR VEHICLE 83 you hear a click. This feature is termed the “Parade” mode NOTE: If your vehicle is equipped with illuminated ap- and is useful when headlights are required during the day. proach lights under the outside mirrors, they can be turned off by moving the instrument panel dimmer into the NOTE: If your vehicle is equipped with a touchscreen, the “Dome Defeat”...
Page 86 84 GETTING TO KNOW YOUR VEHICLE Rotate the end of the lever upward, to the first detent past If the washer knob is depressed while in the delay range, the intermittent settings for low-speed wiper operation. the wiper will operate for several seconds after the washer Rotate the end of the lever upward to the second detent knob is released.
Page 87: Rain Sensing Wipers - If Equipped
GETTING TO KNOW YOUR VEHICLE 85 Mist Feature Position 3 should be used for normal rain conditions. Positions 1 and 2 can be used if the driver desires less When a single wipe to clear off road mist or spray from a wiper sensitivity.
Page 88: Climate Controls
86 GETTING TO KNOW YOUR VEHICLE • Transmission In NEUTRAL Position — When the igni- CLIMATE CONTROLS tion is ON, and the transmission is in the NEUTRAL Manual Climate Controls Without Touchscreen position, the Rain Sensing system will not operate until The controls for the manual heating and air conditioning the wiper switch is moved, vehicle speed is greater than system in this vehicle consist of a series of outer rotary...
Page 89 GETTING TO KNOW YOUR VEHICLE 87 Manual Climate Control Descriptions Icon Description MAX A/C Setting Rotate the Temperature Control Knob counterclockwise until it is set to MAX A/C. This is the coldest setting and will put the A/C to its maximum power. A/C Button Push the A/C button to engage the Air Conditioning (A/C).
Page 90 88 GETTING TO KNOW YOUR VEHICLE Icon Description Front Defrost Setting Turn the Mode Control knob to the Defrost mode. Air comes from the windshield and side win- dow demist outlets. Use Defrost mode with maximum temperature settings for best windshield and side window defrosting and defogging.
Page 91 GETTING TO KNOW YOUR VEHICLE 89 Icon Description Modes Control: Rotate the Mode Control Knob to change the airflow distribution mode. The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets. The Mode settings are as follows: Panel Mode Panel Mode Air comes from the outlets in the instrument panel.
Page 92 90 GETTING TO KNOW YOUR VEHICLE Economy Mode If ECONOMY mode is desired, push the A/C button to turn off the LED indicator and the A/C compressor. Rotate the temperature control knob to the desired temperature. Also, make sure to select only Panel, Bi-Level or Floor modes.
Page 93: Manual Climate Controls With A Touchscreen
GETTING TO KNOW YOUR VEHICLE 91 Manual Climate Controls With A Touchscreen Uconnect 4C/4C NAV With Manual Temperature Controls...
Page 94 92 GETTING TO KNOW YOUR VEHICLE Manual Climate Control With Touchscreen Descriptions Icon Description MAX A/C Setting Press the button to select MAX A/C. This is the coldest setting and will put the A/C to its maximum power. A/C Button Push the A/C button on the touchscreen or faceplate to engage the Air Conditioning (A/C).
Page 95 GETTING TO KNOW YOUR VEHICLE 93 Icon Description Front Defrost Setting Push the button to activate Defrost mode. Air comes from the windshield and side window de- mist outlets. Use Defrost mode with maximum temperature settings for best windshield and side window defrosting and defogging.
Page 96 94 GETTING TO KNOW YOUR VEHICLE Icon Description Panel Mode Panel Mode Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. The air vanes of the center outlets and outboard outlets can be moved up and down or side to side to regulate airflow direction.
Page 97 GETTING TO KNOW YOUR VEHICLE 95 Economy Mode If ECONOMY mode is desired, push the A/C button to turn off the LED indicator and the A/C compressor. Rotate the temperature control knob to the desired temperature. Also, make sure to select only Panel, Bi-Level or Floor modes.
Page 98: Automatic Climate Controls With A Touchscreen
96 GETTING TO KNOW YOUR VEHICLE Automatic Climate Controls With A Touchscreen Uconnect 3 With 5–inch Display With Automatic Temperature Controls...
Page 99 GETTING TO KNOW YOUR VEHICLE 97 Uconnect 4C/4C NAV With Automatic Temperature Controls...
Page 100 98 GETTING TO KNOW YOUR VEHICLE Control Descriptions NOTE: Icons and descriptions can vary based upon vehicle equipment. Icon Description MAX A/C Button Press and release to change the current setting, the indicator illuminates when MAX A/C is on. Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.
Page 101 GETTING TO KNOW YOUR VEHICLE 99 Icon Description AUTO Button — If Equipped Automatically controls the interior cabin temperature by adjusting airflow distribution and amount. Toggling this function will cause the system to switch between manual mode and auto- matic modes. Refer to “Automatic Operation” for more information. Front Defrost Button Press and release the touchscreen button, or push and release the button on the faceplate, to change the current airflow setting to Defrost mode.
Page 102 100 GETTING TO KNOW YOUR VEHICLE Icon Description Uconnect 3 Driver and Passenger Temperature Up and Down Buttons Provides the driver and passenger with independent temperature control. Push the up arrow button on the faceplate, press the up arrow button on the touchscreen, or press and slide the temperature bar towards the red arrow button on the touchscreen for warmer temperature set- tings.
Page 103 GETTING TO KNOW YOUR VEHICLE 101 Icon Description Faceplate Knob Blower Control Blower Control is used to regulate the amount of air forced through the climate system. There are seven blower speeds available. The speeds can be selected using either the blower control knob on the faceplate or the buttons on the touchscreen.
Page 104 102 GETTING TO KNOW YOUR VEHICLE Icon Description Floor Mode Floor Mode Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Mix Mode Mix Mode Air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield.
Page 105: Climate Control Functions
GETTING TO KNOW YOUR VEHICLE 103 Climate Control Functions MAX A/C A/C (Air Conditioning) MAX A/C sets the control for maximum cooling perfor- mance. The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning sys- Press and release to toggle between MAX A/C and the prior tem.
Page 106: Automatic Temperature Control (Atc) - If Equipped
104 GETTING TO KNOW YOUR VEHICLE Automatic Temperature Control (ATC) — If NOTE: Equipped • It is not necessary to move the temperature settings for cold or hot vehicles. The system automatically adjusts Automatic Operation the temperature, mode, and blower speed to provide 1.
Page 107 GETTING TO KNOW YOUR VEHICLE 105 Summer Operation Window Fogging The engine cooling system must be protected with a Vehicle windows tend to fog on the inside in mild, rainy, high-quality antifreeze coolant to provide proper corrosion and/or humid weather. To clear the windows, select De- protection and to protect against engine overheating.
Page 108 106 GETTING TO KNOW YOUR VEHICLE Operating Tips Chart...
Page 109: Windows
GETTING TO KNOW YOUR VEHICLE 107 WINDOWS ignition switch is turned to the ON/RUN or ACC position, and for up to 10 minutes after the ignition is turned OFF or Power Windows — If Equipped until a front door is opened. NOTE: The Key Off Power Delay feature will allow the power windows to operate for up to 10 minutes after the ignition is turned OFF.
Page 110 108 GETTING TO KNOW YOUR VEHICLE first detent, release, and the window will go down auto- NOTE: If the window runs into any obstacle during the matically. To cancel the Auto-Down movement, operate the Auto-Closure, it will reverse direction and then go back switch in either the up or down direction and release the down.
Page 111: Wind Buffeting
GETTING TO KNOW YOUR VEHICLE 109 3. Push the window switch down firmly to the second detent to open the window completely and continue to hold the switch down for an additional two seconds after the window is fully open. Window Lockout Switch (4–Door Models Only) The window lockout switch on the driver’s door allows you to disable the window control on the rear passenger...
Page 112: Power Sunroof - If Equipped
110 GETTING TO KNOW YOUR VEHICLE POWER SUNROOF — IF EQUIPPED WARNING! (Continued) The power sunroof switch is located on the overhead equipped with Keyless Enter-N-Go in the ACC or console between the courtesy/reading lights. ON/RUN mode. Occupants, particularly unattended children, can become entrapped by the power sun- roof while operating the power sunroof switch.
Page 113: Closing Sunroof
GETTING TO KNOW YOUR VEHICLE 111 Manual down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and To open the sunroof, push and hold the switch rearward to can be minimized. If the buffeting occurs with the rear full open.
Page 114: Venting Sunroof - Express
112 GETTING TO KNOW YOUR VEHICLE Venting Sunroof — Express HOOD Push and release the Vent button within one half second To Open The Hood and the sunroof will open to the vent position. This is To open the hood, two latches must be released. called “Express Vent”...
Page 115: To Close The Hood
GETTING TO KNOW YOUR VEHICLE 113 2. Reach into the opening beneath the center of the hood WARNING! and push the safety latch lever to the left to release it, before raising the hood. Be sure the hood is fully latched before driving your vehicle.
Page 116: Garage Door Opener - If Equipped
114 GETTING TO KNOW YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED WARNING! HomeLink replaces up to three hand-held transmitters that • Your motorized door or gate will open and close operate devices such as garage door openers, motorized while you are training the universal transceiver. Do gates, lighting or home security systems.
Page 117: Before You Begin Programming Homelink
GETTING TO KNOW YOUR VEHICLE 115 Before You Begin Programming HomeLink • Erasing all channels should only be performed when programming HomeLink for the first time. Do not erase Ensure your vehicle is parked outside of the garage before channels when programming additional buttons. you begin programming.
Page 118 116 GETTING TO KNOW YOUR VEHICLE 3. Push and hold the HomeLink button you want to program while you push and hold the hand - held transmitter button. 4. Continue to hold both buttons until the instrument cluster display changes from “CHANNEL # TRAIN- ING”...
Page 119: Programming A Non-Rolling Code
GETTING TO KNOW YOUR VEHICLE 117 Programming A Non-Rolling Code 6. Return to the vehicle and push the programmed HomeLink button twice (holding the button for two For programming Garage Door Openers manufactured seconds each time). The instrument cluster display will before 1995.
Page 120: Canadian/Gate Operator Programming
118 GETTING TO KNOW YOUR VEHICLE 5. Push and hold the programmed HomeLink button. The Canadian radio frequency laws require transmitter signals instrument cluster display will display “CHANNEL # to time-out (or quit) after several seconds of transmission – TRANSMIT.” If the garage door opener/device acti- which may not be long enough for HomeLink to pick up vates, programming is complete.
Page 121: Using Homelink
GETTING TO KNOW YOUR VEHICLE 119 4. Continue to hold both buttons until the instrument NOTE: For vehicle’s equipped with Keyless Enter-N-Go, cluster display changes from “CHANNEL # TRAIN- place the ignition in the RUN position with the Engine ON. ING”...
Page 122: Security
120 GETTING TO KNOW YOUR VEHICLE Security If you have any problems, or require assistance, please call toll-free 1-800-355-3515 Internet It is advised to erase all channels before you sell or turn in HomeLink.com for information or assistance. your vehicle. To erase the channels press and hold the two outside WARNING! HomeLink buttons (I and III) for up 20 seconds.
Page 123: General Information
GETTING TO KNOW YOUR VEHICLE 121 General Information INTERNAL EQUIPMENT The following regulatory statement applies to all Radio Storage Frequency (RF) devices equipped in this vehicle: Glove Compartment This device complies with Part 15 of the FCC Rules and The glove compartment is located on the passenger side of with Industry Canada license-exempt RSS standard(s).
Page 124 122 GETTING TO KNOW YOUR VEHICLE To open the upper glove compartment, push upward on To open the lower glove compartment, pull the release the handle release. The glove compartment door will handle. automatically open. Lower Glove Compartment Upper Glove Compartment...
Page 125 GETTING TO KNOW YOUR VEHICLE 123 Door Storage Rear Door Storage — If Equipped Front Door Storage — If Equipped Storage compartments are located in both the driver and passenger rear door trim panels. Storage areas and bottle holders (driver’s side only) are located in the door trim panels.
Page 126 124 GETTING TO KNOW YOUR VEHICLE Pull on the upper handle on the front of the armrest to raise the cover. The upper storage area contains a USB power outlet that can be used to power small electrical devices, refer to “Electrical Power Outlets” for further information. Center Storage Compartment WARNING! •...
Page 127 GETTING TO KNOW YOUR VEHICLE 125 The center console is equipped with a front storage bin located next to the cupholders. This storage bin may be equipped with a manual sliding top door. Lower Storage Bin WARNING! Do not operate this vehicle with a console compart- Front Storage Bin With Door —...
Page 128 126 GETTING TO KNOW YOUR VEHICLE Seatback Storage Second Row In-Floor Storage Bin — If Equipped Located in the back of both the driver and passenger front In-floor storage bins are located in front of the second row seats are pockets that can be used for storage. seats and can be used for extra storage.
Page 129 GETTING TO KNOW YOUR VEHICLE 127 To open in-floor storage bin, lift upward on the handle of Storage Bin (Regular Cab) the latch and open the lid. The storage bin is located behind the front seats and runs the length of the cab. NOTE: The front seat may have to be moved forward to fully open the lid.
Page 130 128 GETTING TO KNOW YOUR VEHICLE Fold Flat Load Floor — If Equipped Unfolding The Load Floor/Quad Cab Quad Cab and Crew Cab models with a 60/40 rear seat 1. Lift the 60/40 seat cushion(s) to the upward position. may be equipped with a folding load floor. WARNING! Do not operate the vehicle with loose items stored on the load floor.
Page 131 GETTING TO KNOW YOUR VEHICLE 129 Unfolding The Load Floor/Crew Cab 1. Lift the 60/40 seat cushion(s) to the upward position. Load Floor In Open Position 3. Reverse the procedure to store the load floor. Load Floor Legs In Stowed Position 2.
Page 132 130 GETTING TO KNOW YOUR VEHICLE Load Floor Legs In Opened Position Load Floor In Open Position 3. Lift the front panel until the load floor unfolds into 4. Reverse the procedure to store the load floor. position. Positioning The Load Floor For Storage Access Under The Seat 1.
Page 133 GETTING TO KNOW YOUR VEHICLE 131 Crew Cab — If Equipped WARNING! Do not drive with the load floor in the up position. When stopping fast or in an accident, the load floor could move to the down position causing serious injury.
Page 134: Cupholders
132 GETTING TO KNOW YOUR VEHICLE Cupholders To open the storage compartments, unsnap the securing snap located at either side of the load floor and lift upward Front Seat Cupholders on the fold flat lid. For vehicles equipped with bucket seats, two cupholders are located next to the center console storage bin.
Page 135: Electrical Power Outlets
GETTING TO KNOW YOUR VEHICLE 133 Rear Cupholders — If Equipped Some vehicles are equipped with rear cupholders located in the center armrest. Rear Cup Wells Electrical Power Outlets The auxiliary 12 Volt (13 Amp) power outlets can provide power for in-cab accessories designed for use with the Rear Armrest Cupholder standard “cigar lighter”...
Page 136 134 GETTING TO KNOW YOUR VEHICLE A key symbol indicates that the key must be in the The auxiliary power outlets can be found in the following ON/RUN or ACC positions for the outlet to provide locations: power. The battery symbol indicates that the outlet is •...
Page 137 GETTING TO KNOW YOUR VEHICLE 135 • Center console when equipped with bucket seats. • Rear of the center console storage compartment — Quad Cab or Crew Cab. Power Outlet — Center Console Power Outlet — Rear Center Console...
Page 138 136 GETTING TO KNOW YOUR VEHICLE Power Outlet — Rear Center Console Fuse Power Outlet Fuse Locations 1 — F104 Fuse 20 A Yellow Power Outlet Center Console Bin / USB Port (Charge Only) 2 — F90–F91 Fuse 20 A Yellow Power Outlet Rear Center Console 3 —...
Page 139: Cigar Lighter And Ash Receiver - If Equipped
GETTING TO KNOW YOUR VEHICLE 137 WARNING! CAUTION! (Continued) • After the use of high power draw accessories, or long To avoid serious injury or death: periods of the vehicle not being started (with acces- • Only devices designed for use in this type of outlet sories still plugged in), the vehicle must be driven a should be inserted into any 12 Volt outlet.
Page 140: Auxiliary Switches - If Equipped
138 GETTING TO KNOW YOUR VEHICLE WARNING! To avoid serious injury or death: • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use. • If this outlet is mishandled, it may cause an electric shock and failure.
Page 141: Pickup Box
NOTE: Holding last state conditions are met when switch type is set to latching and power source is set to ignition. For further information on using the auxiliary switches, please refer to the Ram Body Builders Guide by accessing www.rambodybuilder.com and choosing the appropriate links.
Page 142: Cargo Camera - If Equipped
140 GETTING TO KNOW YOUR VEHICLE box in the indentations provided above the wheel housings There are stampings in the sheet metal on the inner side and in the bulkhead dividers to form the floor. bulkheads of the box in front of and behind both wheel housings.
Page 143: Rambox - If Equipped
GETTING TO KNOW YOUR VEHICLE 141 A touchscreen button X to disable display of the camera NOTE: Once initiated by the Cargo Camera button, the image is made available when the vehicle is not in RE- Cargo Camera image may be deactivated by pressing the VERSE gear.
Page 144 142 GETTING TO KNOW YOUR VEHICLE To open a storage bin with the RamBox unlocked, push and release the button located on the lid. The RamBox lid will open upward to allow hand access. Lift the lid to fully open. NOTE: RamBox will not open when the pushbutton is pushed if the RamBox is locked.
Page 145: Locking And Unlocking Rambox
GETTING TO KNOW YOUR VEHICLE 143 CAUTION! Leaving the lid open for extended periods of time could cause the vehicle battery to discharge. If the lid is required to stay open for extended periods of time, it is recommended that the bin lights be turned off manually using the on/off switch.
Page 146: Rambox Safety Warning
144 GETTING TO KNOW YOUR VEHICLE RamBox Safety Warning be locked using the vehicle key. To lock and unlock the storage bin, insert the key into the keyhole on the push Carefully follow these warnings to help prevent personal button and turn clockwise to lock or counterclockwise to injury or damage to your vehicle: unlock.
Page 147: Bed Extender - If Equipped
GETTING TO KNOW YOUR VEHICLE 145 Bed Extender — If Equipped RamBox Storage Bin Cover Emergency Release Lever — If Equipped The bed extender has three functional positions: As a security measure, a Storage Bin Cover Emergency • Storage Position Release is built into the storage bin cover latching mecha- •...
Page 148 146 GETTING TO KNOW YOUR VEHICLE To install the bed extender into the storage position, 2. With the side gates open, position the extender fully perform the following: forward in the bed against the front panel. 1. Make sure the center handle is unlocked using the vehicle key and rotate the center handle vertically to release the extender side gates.
Page 149 GETTING TO KNOW YOUR VEHICLE 147 3. Rotate the side gates closed allowing the outboard ends to be positioned in front of the cargo tie down loops. Side Gates Closed 5. Lock the center handle using the vehicle key to secure the panel into place.
Page 150 148 GETTING TO KNOW YOUR VEHICLE To install the bed extender into a divider position, perform the following: 1. Make sure the center handle is unlocked using the vehicle key and rotate the center handle vertically to release the extender side gates. Aligning Gate To Slots 3.
Page 151 GETTING TO KNOW YOUR VEHICLE 149 Side Gates Closed Extender Position 5. Lock the center handle to secure the panel into place. To install the bed extender into the extender position, perform the following: Extender Position 1. Lower the tailgate. The extender position allows you to load the bed of the truck beyond the tail gate.
Page 152 150 GETTING TO KNOW YOUR VEHICLE 3. Fit the end of the side gate ends onto the pin and handle. Locking Tab Extender Installation WARNING! 4. Rotate the handles to the horizontal position to secure To reduce the risk of potential injury or property into place.
Page 153: Bed Rail Tie-Down System
GETTING TO KNOW YOUR VEHICLE 151 WARNING! (Continued) • When vehicle is in motion do not exceed 150 lbs (68 kg) load on the tailgate. • The bed extender is not intended for off road use. • When not in use, the extender/divider should be in stowed or divider position with the tailgate closed.
Page 154: Slide-In Campers
152 GETTING TO KNOW YOUR VEHICLE Adjustable Cleat Assembly Utility Rail End Cap SLIDE-IN CAMPERS 1 — Utility Rail Detent 2 — Cleat Retainer Nut Camper Applications 3 — Utility Rail Cleat Certain truck models are not recommended for slide-in campers.
Page 155: Easy-Off Tailgate
GETTING TO KNOW YOUR VEHICLE 153 EASY-OFF TAILGATE To simplify mounting of a camper unit with an overhang, the tailgate can be removed. NOTE: If your vehicle is equipped with a rear camera or Remote Keyless Entry, the electrical connector must be disconnected prior to removing the tailgate.
Page 156: Removing The Tailgate
154 GETTING TO KNOW YOUR VEHICLE 6. Tape the tailgate harness and bracket against the forward-facing surface of the tailgate. This will prevent damaging the connector and bracket when storing or reinstalling the tailgate. Removing The Tailgate 1. Disconnect the wiring harness for the rear camera and or power locks (if equipped), refer to “Disconnecting The Rear Camera —...
Page 157: Locking Tailgate
GETTING TO KNOW YOUR VEHICLE 155 WARNING! To avoid inhaling carbon monoxide, which is deadly, the exhaust system on vehicles equipped with “Cap or Slide-In Campers” should extend beyond the over- hanging camper compartment and be free of leaks. Locking Tailgate The lock is located next to the tailgate handle.
Page 158: Tri-Fold Tonneau Cover Removal
156 GETTING TO KNOW YOUR VEHICLE NOTE: The Tonneau Cover can be folded up and secured at the front of the box without removing completely. Tri-Fold Tonneau Cover Removal To remove the Tonneau Cover follow the following steps: 1. Lower the tailgate to gain access to the first set of two Tonneau Cover clamps located on the driver and pas- senger underside of the Tonneau Cover.
Page 159 GETTING TO KNOW YOUR VEHICLE 157 Proper Released Position Second Panel Position 5. Pick up on the cover and fold it back onto the third CAUTION! panel. Make sure the tonneau cover clamp and clamp wire are in the proper released position. If the clamp and clamp wire are not properly released, damage to the tonneau cover material will result.
Page 160 158 GETTING TO KNOW YOUR VEHICLE Third Panel Position Semi Clamped Position 6. Once in the third panel position, pull down on the 7. Pull down on the clamp wire and push the clamp up second set of clamps on both driver and passenger sides into the proper released position.
Page 161: Tri-Fold Tonneau Cover Installation
GETTING TO KNOW YOUR VEHICLE 159 Proper Released Position Stowage Strap 8. Be sure to clip both stowage straps together to ensure 9. With two people, remove the cover. the cover stays together. NOTE: Be sure the Tonneau Cover has been folded com- pletely before removing.
Page 162 2. Pull down on the first set of clamp handles to release the 3. Push clamp wires up and under the flange of box (or clamps from the stowed position. flange of Ram Box rail, if equipped) to the semi clamped position. Stowed Position...
Page 163 GETTING TO KNOW YOUR VEHICLE 161 4. Push clamp handles upward to the clamped position to properly engage the clamps. Improper Clamp Position 5. Disengage the stowage straps. Clamped Position NOTE: Once clamped, be sure the clamps are not partially clamped to the truck bed flange.
Page 164 162 GETTING TO KNOW YOUR VEHICLE 6. Unfold Tonneau Cover to the intermediate position. 7. Completely unfold the Tonneau Cover. NOTE: The vehicle cannot be driven when the Tonneau Cover is in this position. Fully Unfolded Position Intermediate Position (Vehicle Cannot Be Driven)
Page 165 8. Pull down on the second set of clamp handles to release 9. Push clamp wires up and under the flange of box (or the clamps from the stowed position. flange of Ram Box rail, if equipped) to the semi clamped position. Stowed Position...
Page 166 164 GETTING TO KNOW YOUR VEHICLE 10. Push clamp handles upward to the clamped position to NOTE: Once clamped, be sure the clamps are not partially properly engage the clamps. clamped to the truck bed flange. Clamped Position Improper Clamp Position...
Page 167: Tri-Fold Tonneau Cover Cleaning
GETTING TO KNOW YOUR VEHICLE 165 The Tonneau Cover clamps can be locked when in the CAUTION! clamped position by placing a lock through the locking hole. It is the driver’s responsibility to ensure the Tonneau Cover is properly installed on the vehicle. Failure to follow this procedure can result in detachment of the Tonneau Cover from the vehicle and/or damage to the vehicle/Tonneau Cover.
Page 169 GETTING TO KNOW YOUR INSTRUMENT PANEL CONTENTS BASE INSTRUMENT CLUSTER ....168 WARNING LIGHTS AND MESSAGES ..189 ▫ Base Instrument Cluster Descriptions ..169 ▫...
Page 170: Base Instrument Cluster
168 GETTING TO KNOW YOUR INSTRUMENT PANEL BASE INSTRUMENT CLUSTER Base Instrument Clusters...
Page 171: Base Instrument Cluster Descriptions
GETTING TO KNOW YOUR INSTRUMENT PANEL 169 Base Instrument Cluster Descriptions • The gauge pointer will likely indicate a higher tem- perature when driving in hot weather, up mountain 1. Tachometer grades, or when towing a trailer. It should not be •...
Page 172: Premium Instrument Cluster
170 GETTING TO KNOW YOUR INSTRUMENT PANEL PREMIUM INSTRUMENT CLUSTER Premium Instrument Clusters...
Page 173: Premium Instrument Cluster Descriptions
GETTING TO KNOW YOUR INSTRUMENT PANEL 171 Premium Instrument Cluster Descriptions a lubrication system malfunction. Immediate service should be obtained from an authorized dealer. 1. Tachometer 4. Speedometer • Indicates the engine speed in revolutions per minute (RPM x 1000). •...
Page 174: Instrument Cluster Display
172 GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DISPLAY allowed to exceed the upper limits of the normal operating range. Your vehicle may be equipped with an instrument cluster display, which offers useful information to the driver. With WARNING! the ignition in the STOP/OFF mode, opening/closing of a door will activate the display for viewing, and display the A hot engine cooling system is dangerous.
Page 175: Instrument Cluster Display Controls
GETTING TO KNOW YOUR INSTRUMENT PANEL 173 Instrument Cluster Display Controls The instrument cluster display features a driver-interactive display that is located in the instrument cluster. Premium Instrument Cluster Display The instrument cluster display menu items may consist of the following: •...
Page 176 174 GETTING TO KNOW YOUR INSTRUMENT PANEL • Stored Messages • Up Arrow Button • Screen Setup Push and release the up arrow button to scroll upward through the main menu items, submenu • Vehicle Settings (Not Equipped with a Uconnect touch- screen, and vehicle settings.
Page 177: Display Menu Screens
GETTING TO KNOW YOUR INSTRUMENT PANEL 175 Display Menu Screens 3. Main Screen Displays main menu, submenus, settings. 4. White Telltales 5. Amber Telltales 6. Red Telltales 7. Audio/Phone Information And Submenu Information Base Instrument Cluster Display The instrument cluster display screens are located in the center portion of the cluster and consists of seven sections: 1.
Page 178: Gear Selector
176 GETTING TO KNOW YOUR INSTRUMENT PANEL The instrument cluster display screens are located in the 10. Selectable Gauge 1 (Trans Temp, Oil Temp, Oil Life, center portion of the cluster and consists of eight sections: Trailer Brake, Current fuel economy) The instrument cluster display area will normally display 1.
Page 179: Oil Life Reset
GETTING TO KNOW YOUR INSTRUMENT PANEL 177 of this message type are “Turn Signal On” (if a turn signal NOTE: Use the steering wheel instrument cluster display is left on) and “Lights On” (if driver leaves the vehicle). controls for the following procedure(s). •...
Page 180: Display Messages
178 GETTING TO KNOW YOUR INSTRUMENT PANEL • Oil Pressure Low 2. Push and release the down arrow button to scroll downward through the main menu to “Vehicle Info.” • Oil Change Due 3. Push and release the right arrow button to access the •...
Page 181 GETTING TO KNOW YOUR INSTRUMENT PANEL 179 • Service Electronic Throttle Control • Service Airbag System • Lights On • Service Airbag Warning Light • Right Turn Signal Light Out • Driver Seatbelt Unbuckled • Left Turn Signal Light Out •...
Page 182: Display Menu Items
180 GETTING TO KNOW YOUR INSTRUMENT PANEL • Engage Park Brake To Prevent Rolling • Vehicle Cannot Be Lowered Door Open • Transmission Too Cold Idle With Engine On • Off Road 2 Watch For Clearance • Washer Fluid Low •...
Page 183 GETTING TO KNOW YOUR INSTRUMENT PANEL 181 cluster display. Push and release the right arrow button to • Average Fuel Economy Value enter the submenus items of Vehicle Info. Follow the • Range To Empty directional prompts to access or reset any of the following Trip A/Trip B Vehicle Info submenu items: •...
Page 184 182 GETTING TO KNOW YOUR INSTRUMENT PANEL • Output enter the Screen Setup submenu. The Screen Setup feature allows you to change what information is displayed in the • Type instrument cluster as well as the location that information • Gain is displayed.
Page 185 GETTING TO KNOW YOUR INSTRUMENT PANEL 183 Setting Names Setting Names Abbreviated (Left Sub-Menus (Right Submenu Layer) Submenu Layer) Language Select Language English, Spanish, French, Italian, German, Dutch, Portuguese, Arabic (If Equipped) Units Units U.S.; Metric ParkSense ParkSense • Notification — Sound Only; Sound & Display •...
Page 186 184 GETTING TO KNOW YOUR INSTRUMENT PANEL Setting Names Setting Names Abbreviated (Left Sub-Menus (Right Submenu Layer) Submenu Layer) Auto Lock Doors Auto Lock Doors On; Off Auto Unlock Doors Auto Unlock Doors On; Off Sound Horn with Horn w/ Rmt Start On;...
Page 187 GETTING TO KNOW YOUR INSTRUMENT PANEL 185 Setting Names Setting Names Abbreviated (Left Sub-Menus (Right Submenu Layer) Submenu Layer) Commercial Settings Commercial • Aux Switches • Power Take-Off • PIN Setup NOTE: If the vehicle’s PIN is forgotten or not known, see an authorized dealer to have the PIN reset.
Page 188 186 GETTING TO KNOW YOUR INSTRUMENT PANEL Setting Names Setting Names Abbreviated (Left Sub-Menus (Right Submenu Layer) Submenu Layer) • Trailer # (# is equal to slot position) Trailer Name Trailer Name • Boat • Car • Cargo • Dump •...
Page 189: Battery Saver On/Battery Saver Mode Message - Electrical Load Reduction Actions - If Equipped
GETTING TO KNOW YOUR INSTRUMENT PANEL 187 Setting Names Setting Names Abbreviated (Left Sub-Menus (Right Submenu Layer) Submenu Layer) Park Assist Front Park Assist Front On; Off Chime Volume Chime Volume Park Assist Rear Park Assist Rear Chime On; Off Chime Volume Volume Turn Menu Off —...
Page 190 188 GETTING TO KNOW YOUR INSTRUMENT PANEL NOTE: are larger than the capability of charging system. The charging system is still functioning properly. • The charging system is independent from load reduc- tion. The charging system performs a diagnostic on the •...
Page 191: Warning Lights And Messages
GETTING TO KNOW YOUR INSTRUMENT PANEL 189 WARNING LIGHTS AND MESSAGES What to do when an electrical load reduction action message is present (“Battery Saver On” or “Battery Saver Red Warning Lights Mode”) — Seat Belt Reminder Warning Light During a trip: This light indicates when the driver or passenger seat belt •...
Page 192 190 GETTING TO KNOW YOUR INSTRUMENT PANEL — Brake Warning Light NOTE: The light may flash momentarily during sharp cornering maneuvers, which change fluid level conditions. This light monitors various brake functions, including The vehicle should have service performed, and the brake brake fluid level and parking brake application.
Page 193 GETTING TO KNOW YOUR INSTRUMENT PANEL 191 The light also will turn on when the parking brake is — Battery Charge Warning Light applied with the ignition switch in the ON/RUN position. This light illuminates when the battery is not charging properly.
Page 194: Yellow Warning Lights
192 GETTING TO KNOW YOUR INSTRUMENT PANEL and the transmission is placed in the PARK position. The WARNING! light should turn off. If the light remains on with the vehicle running, your vehicle will usually be drivable; Continued operation with reduced assist could pose a however, see an authorized dealer for service as soon as safety risk to yourself and others.
Page 195 GETTING TO KNOW YOUR INSTRUMENT PANEL 193 come on when turning the ignition switch from OFF to CAUTION! ON/RUN, have the condition checked promptly. Prolonged driving with the Malfunction Indicator Certain conditions, such as a loose or missing gas cap, poor Light (MIL) on could cause damage to the vehicle quality fuel, etc., may illuminate the light after engine start.
Page 196 194 GETTING TO KNOW YOUR INSTRUMENT PANEL your authorized dealer as soon as possible to have the — Tire Pressure Monitoring System (TPMS) problem diagnosed and corrected. Warning Light • The “ESC Off Indicator Light” and the “ESC Indicator The warning light switches on and a message is displayed Light”...
Page 197 GETTING TO KNOW YOUR INSTRUMENT PANEL 195 on the vehicle placard or tire inflation pressure label, you minute and then remain continuously illuminated. This should determine the proper tire inflation pressure for sequence will continue upon subsequent vehicle start-ups those tires.) as long as the malfunction exists.
Page 198: Yellow Indicator Lights
196 GETTING TO KNOW YOUR INSTRUMENT PANEL — Low Coolant Level Warning Light CAUTION! (Continued) This telltale will turn on to indicate the vehicle coolant Monitoring System (TPMS) sensor to become inoper- level is low. able. After using an aftermarket tire sealant it is recommended that you take your vehicle to your au- —...
Page 199 GETTING TO KNOW YOUR INSTRUMENT PANEL 197 — TOW/HAUL Indicator Light WARNING! This light will illuminate when TOW/HAUL mode is If you continue operating the vehicle when the Trans- selected. mission Temperature Warning Light is illuminated you — Cargo Light — If Equipped could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.
Page 200: Green Indicator Lights
198 GETTING TO KNOW YOUR INSTRUMENT PANEL — Air Suspension Ride Height Lowering Refer to “Four-Wheel Drive Operation — If Equipped” in Indicator Light— If Equipped “Starting And Operating” for further information on four- wheel drive operation and proper use. This light will blink and alert the driver that the vehicle is changing to a lower ride height.
Page 201: White Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 199 — Speed Control SET Indicator Light — If — Speed Control SET Indicator Light — If Equipped With 7 Inch Instrument Cluster Display Equipped With 3.5 Inch Instrument Cluster Display This light will turn on when the speed control is set. Refer This light will turn on when the speed control is set.
Page 202: Onboard Diagnostic System - Obd Ii
200 GETTING TO KNOW YOUR INSTRUMENT PANEL ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! (Continued) Your vehicle is equipped with a sophisticated Onboard • If the MIL is flashing while the vehicle is running, Diagnostic system called OBD II. This system monitors the severe catalytic converter damage and power loss performance of the emissions, engine, and transmission will soon occur.
Page 203: Emissions Inspection And Maintenance Programs
GETTING TO KNOW YOUR INSTRUMENT PANEL 201 serviced, recently had a dead battery or a battery replace- WARNING! (Continued) ment. If the OBD II system should be determined not ready vehicle control could occur that may result in an for the I/M test, your vehicle may fail the test. accident involving serious injury or death.
Page 204 202 GETTING TO KNOW YOUR INSTRUMENT PANEL • The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off posi- tion or start the engine. This means that your vehicle’s OBD II system is ready and you can proceed to the I/M station.
Page 205 SAFETY CONTENTS SAFETY FEATURES ..... .204 ▫ Child Restraints ..... . .252 ▫...
Page 206: Safety Features
204 SAFETY SAFETY FEATURES These are all normal characteristics of ABS. Anti-Lock Brake System (ABS) WARNING! The Anti-Lock Brake System (ABS) provides increased • The ABS contains sophisticated electronic equip- vehicle stability and brake performance under most brak- ment that may be susceptible to interference caused ing conditions.
Page 207: Electronic Brake Control System
SAFETY benefits of anti-lock brakes. If the “Anti-Lock Brake Warn- WARNING! (Continued) ing Light” does not come on when the ignition is turned to • The capabilities of an ABS equipped vehicle must the ON/RUN mode, have the light repaired as soon as never be exploited in a reckless or dangerous manner possible.
Page 208 206 SAFETY Brake System Warning Light longer desired. Once the brake pedal is released, the BAS is deactivated. The red “Brake System Warning Light” will turn on when the ignition is turned to the ON/RUN mode and may stay WARNING! on for as long as four seconds.
Page 209 SAFETY The following conditions must be met in order for HSA to WARNING! (Continued) activate: while pulling a trailer. HSA is not a substitute for • The feature must be enabled. active driving involvement. It is always the driver’s • The vehicle must be stopped. responsibility to be attentive to distance to other ve- hicles, people, and objects, and most importantly brake •...
Page 210 208 SAFETY For vehicles not equipped with an instrument cluster WARNING! (Continued) display, perform the following steps: order to avoid rolling down an incline while resum- 1. Center the steering wheel (front wheels pointing ing acceleration, manually activate the trailer brake straight forward).
Page 211 SAFETY Traction Control System (TCS) the intended path, ESC applies the brake of the appropriate wheel to assist in counteracting the oversteer or understeer This system monitors the amount of wheel spin of each of condition. the driven wheels. If wheel spin is detected, the TCS may •...
Page 212 210 SAFETY ESC Operating Modes WARNING! (Continued) NOTE: Depending upon model and mode of operation, the road conditions. ESC cannot prevent accidents, in- ESC system may have multiple operating modes. cluding those resulting from excessive speed in turns, driving on very slippery surfaces, or hydro- ESC On planing.
Page 213 SAFETY NOTE: For vehicles with multiple partial ESC modes a message will display in the instrument cluster. To turn ESC momentary button push will toggle the ESC mode. Mul- ON again, momentarily push the “ESC Off” switch. tiple momentary button pushed may be required to return NOTE: System may switch from ESC “Full Off”...
Page 214 212 SAFETY after several ignition cycles, and the vehicle has been WARNING! (Continued) driven several miles (kilometers) at speeds greater than Off” mode is only intended for off-highway or off- 30 mph (48 km/h), see your authorized dealer as soon as road use.
Page 215 SAFETY • The ESC system will make buzzing or clicking sounds NOTE: ERM is disabled anytime the ESC is in “Full Off” when it is active. This is normal; the sounds will stop mode (if equipped). Refer to “Electronic Stability Control when ESC becomes inactive following the maneuver (ESC)”...
Page 216 214 SAFETY NOTE: TSC cannot stop all trailers from swaying. Always 2. Enabled (feature is enabled and ready but activation use caution when towing a trailer and follow the trailer conditions are not met, or driver is actively overriding tongue weight recommendations. Refer to “Trailer Tow- with brake or throttle application).
Page 217 SAFETY • R = 0.6 mph (1 km/h) Driver Override • N = 1.2 mph (2 km/h) The driver may override HDC activation with throttle or brake application at anytime. • D = 0.6 mph (1 km/h) Deactivating HDC • 1st = 0.6 mph (1 km/h) HDC will be deactivated but remain available if any of the •...
Page 218: Auxiliary Driving Systems
216 SAFETY • The vehicle is driven greater than 20 mph (32 km/h) for WARNING! greater than 70 seconds. HDC is only intended to assist the driver in controlling • The vehicle is driven greater than 40 mph (64 km/h) vehicle speed when descending hills.
Page 219 SAFETY Refer to “Tires” in “Servicing And Maintenance” for infor- NOTE: When filling warm tires, the tire pressure may need mation on how to properly inflate the vehicle’s tires. The to be increased up to an additional 4 psi (30 kPa) above the tire pressure will also increase as the vehicle is driven - this recommended cold placard pressure in order to turn the is normal and there should be no adjustment for this...
Page 220 218 SAFETY • Driving on a significantly under-inflated tire causes the CAUTION! (Continued) tire to overheat and can lead to tire failure. Under- equipped on your vehicle. Undesirable system op- inflation also reduces fuel efficiency and tire tread life, eration or sensor damage may result when using and may affect the vehicle’s handling and stopping replacement equipment that is not of the same size, ability.
Page 221 SAFETY The TPMS consists of the following components: • Receiver module • Four tire pressure monitoring sensors • Various tire pressure monitoring system messages, which display in the instrument cluster • Tire pressure monitoring telltale light Tire Pressure Monitoring Low Pressure Warnings The “Tire Pressure Monitoring Telltale Light”...
Page 222 220 SAFETY message will no longer display, and a pressure value will Service TPMS Warning display in place of the dashes. A system fault can occur due If a system fault is detected, the “Tire Pressure Monitoring to any of the following: Telltale Light”...
Page 223 SAFETY flash and the tire pressure display screen will be displayed • For each subsequent ignition switch cycle, a chime will showing the tire pressure values the correct locations. sound, the TPM Telltale Light will flash on and off for 75 seconds and then remain on solid, and the instrument Vehicles With Non Matching Full Size Spare Or Compact cluster will display a SERVICE TPM SYSTEM message...
Page 224 222 SAFETY transmit tire pressure levels. Sensors mounted to each If the ignition switch is cycled, this sequence will repeat, wheel as part of the valve stem transmit tire pressure providing the system fault still exists. If the system fault no readings to the receiver module.
Page 225: Occupant Restraint Systems
SAFETY 2. This device must accept any interference received, in- Here are some simple steps you can take to minimize the cluding interference that may cause undesired opera- risk of harm from a deploying air bag: tion. 1. Children 12 years old and under should always ride NOTE: Changes or modifications not expressly approved buckled up in a vehicle with a rear seat.
Page 226: Seat Belt Systems
224 SAFETY Seat Belt Systems 6. All occupants should always wear their lap and shoul- der belts properly. Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and 7.
Page 227 SAFETY a few seconds. If the driver or outboard front seat passen- Change of Status ger (if equipped with outboard front passenger seat If the driver or outboard front seat passenger (if equipped BeltAlert) is unbuckled when the ignition switch is first in with outboard front passenger seat BeltAlert) unbuckles the START or ON/RUN position the Seat Belt Reminder their seat belt while the vehicle is traveling, the BeltAlert...
Page 228 226 SAFETY Lap/Shoulder Belts WARNING! (Continued) All seating positions except the Quad Cab, Mega Cab and • It is dangerous to ride in a cargo area, inside or outside Crew Cab front center seating position have combination of a vehicle. In a collision, people riding in these areas lap/shoulder belts.
Page 229 SAFETY WARNING! WARNING! (Continued) vehicle in a collision, increasing head and neck • A lap belt worn too high can increase the risk of injury. A seat belt worn under the arm can cause injury in a collision. The seat belt forces won’t be at internal injuries.
Page 230 228 SAFETY equipped with a rear seat). Grasp the latch plate and pull out the seat belt. Slide the latch plate up the webbing as far as necessary to allow the seat belt to go around your lap. Inserting Latch Plate Into Buckle 4.
Page 231 SAFETY Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.
Page 232 230 SAFETY To verify the shoulder belt anchorage is latched, pull downward on the shoulder belt anchorage until it is locked into position. WARNING! • Wearing your seat belt incorrectly could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of the seat belt.
Page 233 SAFETY stored out of the way in the seat for added convenience to open up utilization of the storage areas behind the front seats when the seat is not occupied. 1. Remove the mini-latch plate and regular latch plate from its stowed position on the seat. Mini-Latch And Mini-Buckle Connected 2.
Page 234 232 SAFETY 6. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 7. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt.
Page 235 SAFETY position, your authorized dealer can provide you with a WARNING! (Continued) Seat Belt Extender. The Seat Belt Extender should be used procedure to detach the mini-latch plate and mini- only if the existing seat belt is not long enough. When the buckle, untwist the webbing, and reattach the mini- Seat Belt Extender is not required for a different occupant, latch plate and mini-buckle.
Page 236 234 SAFETY Seat Belts And Pregnant Women Seat Belt Pretensioner The front seat belt system is equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by removing slack from the seat belt early in a collision.
Page 237 SAFETY Switchable Automatic Locking Retractors (ALR) The seat belts in the passenger seating positions may be equipped with a Switchable Automatic Locking Retractor (ALR) which is used to secure a child restraint system. For additional information, refer to “Installing Child Restraints Using The Vehicle Seat Belt”...
Page 238 236 SAFETY webbing necessary to comfortably wrap around the occu- 3. Allow the seat belt to retract. As the seat belt retracts, pant’s mid-section. Slide the latch plate into the buckle you will hear a clicking sound. This indicates the seat until you hear a click.
Page 239: Supplemental Restraint Systems (Srs)
SAFETY Supplemental Restraint Systems (SRS) • Front and Side Impact Sensors — If Equipped Some of the safety features described in this section may be • Seat Belt Pretensioners standard equipment on some models, or may be optional Air Bag Warning Light equipment on others.
Page 240 238 SAFETY Light, either momentarily or continuously. A single chime Have an authorized dealer service the air bag system will sound to alert you if the light comes on again after immediately. initial startup. WARNING! The ORC also includes diagnostics that will illuminate the instrument panel Air Bag Warning Light if a malfunction is Ignoring the Air Bag Warning Light in your instrument detected that could affect the air bag system.
Page 241 SAFETY WARNING! (Continued) • Never place a rear-facing child restraint in front of an air bag. A deploying passenger front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear-facing child restraint.
Page 242 240 SAFETY buckle switch may adjust the inflation rate of the Ad- rollover collisions. The front air bags will not deploy in all vanced Front Air Bags. frontal collisions, including some that may produce sub- stantial vehicle damage — for example, some pole colli- WARNING! sions, truck underrides, and angle offset collisions.
Page 243 • Do not mount any accessories to the knee impact bolsters such as alarm lights, stereos, citizen band radios, etc. Supplemental Side Air Bags Ram 1500 Supplemental Seat-Mounted Side Air Bags (SABs) This vehicle is equipped with Supplemental Seat-Mounted Supplemental Seat-Mounted Side Air Bag Label Side Air Bags (SABs).
Page 244 242 SAFETY and the door. The SAB moves at a very high speed and with such a high force that it could injure occupants if they are not seated properly, or if items are positioned in the area where the SAB inflates. Children are at an even greater risk of injury from a deploying air bag.
Page 245 SAFETY positioned in the area where the SABICs inflate. Children Side Impacts are at an even greater risk of injury from a deploying air The Side Air Bags are designed to activate in certain side bag. impacts. The Occupant Restraint Controller (ORC) deter- The SABICs may help reduce the risk of partial or complete mines whether the deployment of the Side Air Bags in a ejection of vehicle occupants through side windows in...
Page 246 244 SAFETY Side Air Bags are a supplement to the seat belt restraint WARNING! system. Side Air Bags deploy in less time than it takes to blink your eyes. • Side Air Bags need room to inflate. Do not lean against the door or window.
Page 247 The SABICs may help reduce the risk of partial or complete ejection of vehicle occupants through side windows in certain rollover or side impact events. Ram 2500 And 3500 Supplemental Seat-Mounted Side Air Bags (SABs) — If Supplemental Seat-Mounted Side Air Bag Label...
Page 248 246 SAFETY and the door. The SAB moves at a very high speed and with such a high force that it could injure occupants if they are not seated properly, or if items are positioned in the area where the SAB inflates. Children are at an even greater risk of injury from a deploying air bag.
Page 249 SAFETY positioned in the area where the SABICs inflate. Children Side Impacts are at an even greater risk of injury from a deploying air The Side Air Bags are designed to activate in certain side bag. impacts. The Occupant Restraint Controller (ORC) deter- The SABICs (if equipped with SABICs) may help reduce mines whether the deployment of the Side Air Bags in a the risk of partial or complete ejection of vehicle occupants...
Page 250 248 SAFETY Side Air Bags are a supplement to the seat belt restraint WARNING! system. Side Air Bags deploy in less time than it takes to blink your eyes. • Side Air Bags need room to inflate. Do not lean against the door or window.
Page 251 SAFETY The Side Air Bags will not deploy in all rollover events. The • Driver and Front Passenger Air Bags rollover sensing-system determines if a rollover event may • Seat Belt Buckle Switch be in progress and whether deployment is appropriate. A •...
Page 252 250 SAFETY • As the air bags deflate, you may see some smoke-like NOTE: particles. The particles are a normal by-product of the • Air bag covers may not be obvious in the interior trim, process that generates the non-toxic gas used for air bag but they will open during air bag deployment.
Page 253 SAFETY Enhanced Accident Response System Reset WARNING! (Continued) Procedure • It is dangerous to try to repair any part of the air bag In order to reset the Enhanced Accident Response System system yourself. Be sure to tell anyone who works on functions after an event, the ignition switch must be your vehicle that it has an air bag system.
Page 254: Child Restraints
252 SAFETY and safety systems for a short period of time, typically 30 law enforcement, that have the special equipment, can read seconds or less. The EDR in this vehicle is designed to the information if they have access to the vehicle or the record such data as: EDR.
Page 255 SAFETY There are different sizes and types of restraints for children NOTE: from newborn size to the child almost large enough for an • For additional information, refer to www.safercar.gov/ adult safety belt. Always check the child seat Owner’s parents/index.htm or call: 1–888–327–4236 Manual to make sure you have the correct seat for your •...
Page 256 254 SAFETY Recommended Type Of Child Child Size, Height, Weight Or Age Restraint Larger Children Children who have outgrown their Belt Positioning Booster Seat and the forward-facing child restraint, but vehicle seat belt, seated in the rear are too small to properly fit the seat of the vehicle vehicle’s seat belt Children Too Large for...
Page 257 SAFETY Older Children And Child Restraints WARNING! Children who are two years old or who have outgrown Do not install a rear-facing car seat using a rear support their rear-facing convertible child seat can ride forward- leg in this vehicle. The floor of this vehicle is not facing in the vehicle.
Page 258 256 SAFETY should use the seat belt in a rear seat. Use this simple 5-step WARNING! test to decide whether the child can use the vehicle’s seat belt alone: • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. 1.
Page 259 SAFETY WARNING! Never allow a child to put the shoulder belt under an arm or behind their back. In a crash, the shoulder belt will not protect a child properly, which may result in serious injury or death. A child must always wear both the lap and shoulder portions of the seat belt correctly.
Page 260 258 SAFETY Lower Anchors And Tethers For CHildren (LATCH) used with the top tether anchorage to install the child Restraint System restraint. Please see the following table for more information. LATCH Positions For Installing Child Restraints In This Vehicle LATCH Label Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.
Page 261 SAFETY Crew/Mega Cabs 60/40 Split Bench LATCH Positions Quad Cab 60/40 Split Bench LATCH Positions Top Tether Anchorage Symbol Top Tether Anchorage Symbol Lower Anchorage Symbol (2 Anchorages Per Seating Position) Lower Anchorage Symbol (2 Anchorages Per Seating Position)
Page 262 260 SAFETY Quad/Crew Cabs Full Bench LATCH Positions Top Tether Anchorage Symbol Lower Anchorage Symbol (2 Anchorages Per Seating Position) Frequently Asked Questions About Installing Child Restraints With LATCH What is the weight limit (child’s 65 lbs (29.5 kg) Use the LATCH anchorage system weight + weight of the child re- until the combined weight of the straint) for using the LATCH anchor-...
Page 263 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH Can the LATCH anchorages and the Do not use the seat belt when you seat belt be used together to attach a use the LATCH anchorage system to rear-facing or forward-facing child attach a rear-facing or forward-facing restraint? child restraint.
Page 264 262 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH Can the rear-facing child restraint The child seat may touch the back of touch the back of the front passenger the front passenger seat if the child seat? restraint manufacturer also allows contact.
Page 265 SAFETY Locating The Upper Tether Anchorages Regular Cab models have tether strap anchor- ages behind the front center and right seats. Quad Cab, Mega Cab and Crew Cab models have tether strap anchorages located behind each of the rear seats. Crew Or Quad Cab Outboard Tether Anchorage Regular Cab Tether Anchorages (Behind Covers) 1 —...
Page 266 264 SAFETY Crew Or Quad Cab Center Tether Anchorage With Head Mega Cab Tether Anchorages (Behind Covers) Restraint In Raised Position LATCH-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage.
Page 267 SAFETY Center Seat LATCH WARNING! Regular Cab, Quad Cab, Or Crew Cab Full Bench Rear Never use the same lower anchorage to attach more Seat: No Lower Center LATCH Anchorages Available than one child restraint. Please refer to “To Install A LATCH-Compatible Child Restraint”...
Page 268 266 SAFETY forward and rearward in the vehicle, you may wish to How To Stow An Unused Switchable-ALR (ALR) move it to its rear-most position to make room for the Seat Belt: child seat. You may also move the front seat forward to When using the LATCH attaching system to install a child allow more room for the child seat.
Page 269 SAFETY The seat belts in the passenger seating positions are WARNING! (Continued) equipped with either a Switchable Automatic Locking • Child restraint anchorages are designed to withstand Retractor (ALR) or a cinching latch plate or both. Both only those loads imposed by correctly-fitted child types of seat belts are designed to keep the lap portion of restraints.
Page 270 268 SAFETY Please see the table below and the following sections for more information. Lap/Shoulder Belt Systems For Installing Child Restraints In This Vehicle Quad Cab/Mega Cab/Crew Cab Automatic Locking Retractor (ALR) Locations CINCH = Cinching Latchplate ALR = Switchable Automatic Locking Retractor Top Tether Anchorage Symbol Regular Cab Automatic Locking Retractor (ALR) Locations ALR = Switchable Automatic Locking Retractor...
Page 271 SAFETY Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit (child’s Weight limit of the Child Restraint Always use the tether anchor when weight + weight of the child re- using the seat belt to install a for- straint) for using the Tether Anchor ward facing child restraint, up to the with the seat belt to attach a forward...
Page 272 270 SAFETY 1. For Crew, Mega, And Quad Cab Models out of the retractor. Then, allow the webbing to retract back into the retractor. As the webbing retracts, you will Place the child seat in the center of the seating position. For hear a clicking sound.
Page 273 SAFETY Installing A Child Restraint With A Cinching Latch 3. Slide the latch plate into the buckle until you hear a Plate (CINCH) — If Equipped: “click.” Child restraint systems are designed to be secured in 4. Finally, pull up on any excess webbing to tighten the lap vehicle seats by lap belts or the lap belt portion of a portion around the child restraint while you push the lap/shoulder belt.
Page 274 272 SAFETY plate into the buckle with the release button facing out, WARNING! (Continued) away from the child restraint. Repeat steps 4 to 6, above, to Restraint System” for the location of approved tether complete the installation of the child restraint. anchorages in your vehicle.
Page 275 SAFETY 3. Lift the cover (if so equipped), and attach the hook to the square opening in the sheet metal. Tighten the tether strap according to the child seat manufacturer’s instruc- tions. Regular Cab Tether Anchorages 1 — Tether Strap Hook 2 —...
Page 276 274 SAFETY Quad Cab Or Crew Cab Trucks: The top tether anchorages in this vehicle are tether strap loops located between the rear glass and the back of the rear seat. There is a tether strap loop located behind each seating position.
Page 277 SAFETY Tether Strap Through Outboard Tether Strap Loop Tether Strap Through Outboard Tether Strap Loop And Attached To Center Tether Strap Loop 4. Attach the hook to the center tether strap loop (see NOTE: If there are child seats in both of the outboard (left diagram).
Page 278 276 SAFETY Center Seat: 3. Pass the tether strap hook under the head restraint behind the child seat, though the tether strap loop 1. Raise the head restraint and reach between the rear seat behind the seat and over to the right or left outboard and rear glass to access the tether strap loop.
Page 279 SAFETY 4. Attach the hook to the outboard tether strap loop (see 3. Place a child restraint on the center rear seat. Route the diagram). Tighten the tether strap according to the child tether strap following the directions for the center seat manufacturer’s instructions.
Page 280: Transporting Pets
278 SAFETY SAFETY TIPS WARNING! Transporting Passengers • An incorrectly anchored tether strap could lead to NEVER TRANSPORT PASSENGERS IN THE CARGO increased head motion and possible injury to the AREA. child. Use only the anchorage position directly be- hind the child seat to secure a child restraint top WARNING! tether strap.
Page 281: Exhaust Gas
SAFETY Exhaust Gas vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the complete WARNING! exhaust system and adjacent body areas for broken, dam- aged, deteriorated, or mispositioned parts. Open seams or Exhaust gases can injure or kill.
Page 282 280 SAFETY have the system inspected at your authorized dealer as WARNING! soon as possible. After the bulb check, this light will illuminate with a single chime when a fault with the Air An improperly attached, damaged, folded, or stacked Bag System has been detected.
Page 283: Periodic Safety Checks You Should Make
SAFETY WARNING! (Continued) WARNING! (Continued) vehicle properly parked with the engine off, fully interference with the accelerator, brake, or clutch depress the accelerator, the brake, and the clutch pedals then re-install the floor mats. • It is recommended to only use mild soap and water pedal (if present) to check for interference.
Page 284 282 SAFETY Door Latches Check for proper closing, latching, and locking. Fluid Leaks Check area under the vehicle after overnight parking for fuel, coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, or brake fluid leaks are suspected.
Page 285 STARTING AND OPERATING CONTENTS STARTING THE ENGINE — AUTOMATIC TRANSMISSION ....297 GASOLINE ENGINE .....288 ▫...
Page 286 284 STARTING AND OPERATING ▫ Four-Position Electronically Shifted Transfer Case AIR SUSPENSION SYSTEM (2500/3500 MODELS) — (Eight Speed Transmission Only) — IF EQUIPPED ......356 If Equipped .
Page 287 STARTING AND OPERATING 285 ▫ Airing Down For Off-Road Driving ..371 ▫ To Activate ......395 ▫...
Page 288 286 STARTING AND OPERATING ▫ ParkSense Warning Display....405 ▫ Inflation Pressure ..... . .415 ▫...
Page 289 STARTING AND OPERATING 287 RECREATIONAL TOWING (BEHIND DRIVING TIPS ......441 MOTORHOME, ETC.) ....436 ▫...
Page 290: Starting The Engine - Gasoline Engine
288 STARTING AND OPERATING STARTING THE ENGINE — GASOLINE ENGINE WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust both operate power windows, other controls, or move the inside and outside mirrors, and fasten your seat belt. vehicle. • Do not leave children or animals inside parked The starter should not be operated for more than 10-second vehicles in hot weather.
Page 291: Tip Start Feature
STARTING AND OPERATING 289 Tip Start Feature Normal Starting Using ENGINE START/STOP Button Do not press the accelerator. Cycle the ignition switch briefly to the START position and release it. The starter To Turn On The Engine Using The ENGINE START/ motor will continue to run and will automatically disen- STOP Button gage when the engine is running.
Page 292 290 STARTING AND OPERATING 3. If the gear selector is not in PARK, the ENGINE START/ To change the ignition modes without starting the vehicle STOP button must be held for two seconds or three short and use the accessories, follow these directions: pushes in a row with the vehicle speed above 5 MPH 1.
Page 293 STARTING AND OPERATING 291 • Vehicle Speed is 1.2 MPH (1.9 km/h) or less WARNING! • Ignition switched from RUN to ACC • Driver inattention could lead to failure to place the NOTE: For Keyless Go equipped vehicles, The engine will vehicle in PARK.
Page 294 292 STARTING AND OPERATING NOTE: In some cases the ParkSense graphic will be 4WD LOW — If Equipped displayed in the instrument cluster, causing the “ Au- AutoPark will be disabled when operating the vehicle in toPark Engaged Shift to P then Shift to Gear” to not be 4WD LOW.
Page 295: Idle Shutdown - 6.4L Engine Only
STARTING AND OPERATING 293 Idle Shutdown — 6.4L Engine Only WARNING! This feature can be enabled so that the truck will automati- • Never pour fuel or other flammable liquid into the cally shutdown when the truck has been idling for a set throttle body air inlet opening in an attempt to start period of time when the engine is at operating tempera- the vehicle.
Page 296: Cold Weather Operation
294 STARTING AND OPERATING If the engine has been flooded, it may start to run, but not 1500 Models have enough power to continue running when the ignition The engine block heater cord is routed under the hood on button/key is released. If this occurs, continue cranking the passenger side of the vehicle near the right head lamp with the accelerator pedal pushed all the way to the floor.
Page 297: Engine Break-In Recommendations
STARTING AND OPERATING 295 ENGINE BREAK-IN RECOMMENDATIONS NOTE: A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This A long break-in period is not required for the engine and should be considered a normal part of the break-in and not drivetrain (transmission and axle) in your vehicle.
Page 298 296 STARTING AND OPERATING When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. Apply the parking brake before placing the gear selector in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the gear selector out of PARK.
Page 299: Automatic Transmission
STARTING AND OPERATING 297 AUTOMATIC TRANSMISSION WARNING! (Continued) ACC or ON/RUN mode. A child could operate power WARNING! windows, other controls, or move the vehicle. • It is dangerous to shift out of PARK or NEUTRAL if • Be sure the parking brake is fully disengaged before the engine speed is higher than idle speed.
Page 300: Key Ignition Park Interlock
298 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • When leaving the vehicle, always make sure the Enter-N-Go) in the ACC or ON/RUN mode. A child ignition is in the OFF mode, remove the key fob from could operate power windows, other controls, or the vehicle, and lock the vehicle.
Page 301: Brake/Transmission Shift Interlock System
STARTING AND OPERATING 299 Eight-Speed Automatic Transmission — If ignition when the ignition is in the LOCK/OFF position, and the transmission is locked in PARK whenever the Equipped ignition is in the LOCK/OFF position. The transmission is controlled using a rotary electronic gear selector located on the instrument panel.
Page 302 300 STARTING AND OPERATING may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles (kilometers). Only shift from DRIVE to PARK or REVERSE when the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when shifting between these gears.
Page 303 STARTING AND OPERATING 301 Never attempt to use PARK while the vehicle is in motion. WARNING! Apply the parking brake when exiting the vehicle in this range. • Never use the PARK position as a substitute for the park brake. Always apply the park brake fully when When parking on a level surface, you may shift the exiting the vehicle to guard against vehicle move- transmission into PARK first, and then apply the parking...
Page 304 302 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) engine is idling normally and your foot is firmly touch the park brake, brake pedal or the transmis- pressing the brake pedal. sion gear selector. • Unintended movement of a vehicle could injure •...
Page 305 STARTING AND OPERATING 303 The following indicators should be used to ensure that you WARNING! (Continued) have properly engaged the transmission into the PARK that limit your response to changing traffic or road position: conditions. You might lose control of the vehicle and •...
Page 306 304 STARTING AND OPERATING towing a heavy trailer), select TOW/HAUL mode or use message in the instrument cluster will inform the driver of the Electronic Range Select (ERS) shift control (refer to the more serious conditions, and indicate what actions may Electronic Range Select (ERS) Operation in this section for be necessary.
Page 307 STARTING AND OPERATING 305 NOTE: Even if the transmission can be reset, we recom- mend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnos- tic equipment to assess the condition of your transmission. If the transmission cannot be reset, authorized dealer service is required.
Page 308: Models Only (If Equipped)
306 STARTING AND OPERATING When to Use TOW/HAUL Mode at engine start-up. If TOW/HAUL mode is desired, the switch must be pushed each time the engine is started. When driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting occurs, WARNING! push the TOW/HAUL switch to activate TOW/HAUL mode.
Page 309 STARTING AND OPERATING 307 The electronically-controlled transmission provides a pre- NOTE: After selecting any gear range, wait a moment to cise shift schedule. The transmission electronics are self- allow the selected gear to engage before accelerating. This calibrating; therefore, the first few shifts on a new vehicle is especially important when the engine is cold.
Page 310 308 STARTING AND OPERATING • Shift the transmission into PARK. WARNING! (Continued) • Turn the engine OFF. • Unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you • Remove the key fob. should never exit a vehicle while the engine is running.
Page 311 STARTING AND OPERATING 309 • Release the gear selector and make sure it is fully seated WARNING! (Continued) in the PARK gate. • Do not leave the key fob in or near the vehicle (or in • Look at the transmission gear position display and a location accessible to children), and do not leave verify that it indicates the PARK position (P).
Page 312 310 STARTING AND OPERATING Operation” in this section for further information) to select CAUTION! a lower gear range. Under these conditions, using a lower gear range will improve performance and extend transmis- Towing the vehicle, coasting, or driving for any other sion life by reducing excessive shifting and heat buildup.
Page 313 STARTING AND OPERATING 311 During cold temperatures, transmission operation may be In the event of a momentary problem, the transmission can modified depending on engine and transmission tempera- be reset to regain all forward gears by performing the ture as well as vehicle speed. This feature improves warm following steps: up time of the engine and transmission to achieve maxi- 1.
Page 314 312 STARTING AND OPERATING Electronic Range Select (ERS) Operation — gear in the instrument cluster, and set that gear as the top Six-Speed Transmission (1500 Models Only) available gear. For example, if you are in DRIVE and are in third (direct) gear, when you tap the gear selector/switch The Electronic Range Select (ERS) shift control allows the one time in the (-) direction, the display will show 4 (ERS driver to limit the highest available gear when the trans-...
Page 315 STARTING AND OPERATING 313 NOTE: To select the proper gear position for maximum deceleration (engine braking), simply press and hold the gear selector to the left (-) (console shift) or the ERS (-) switch down (column shift). The transmission will shift to the range from which the vehicle can best be slowed down.
Page 316 314 STARTING AND OPERATING • Vehicle speed is sufficiently high, • The TOW/HAUL switch has not been activated, and • The driver is not heavily pressing the accelerator. When To Use TOW/HAUL Mode When driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting occurs, push the TOW/HAUL switch to activate TOW/HAUL mode.
Page 317: Six-Speed Automatic Transmission - 2500/3500
STARTING AND OPERATING 315 seem as if the transmission is not shifting properly when WARNING! cold. This is normal. Using the Electronic Range Select (ERS) shift control, when the transmission is sufficiently Do not use the “TOW/HAUL” feature when driving in warm, will demonstrate that the transmission is able to icy or slippery conditions.
Page 318 316 STARTING AND OPERATING The electronically-controlled transmission provides a pre- Gear Ranges cise shift schedule. The transmission electronics are self- Do not depress the accelerator pedal when shifting from calibrating; therefore, the first few shifts on a new vehicle PARK or NEUTRAL into another gear range. may be somewhat abrupt.
Page 319 STARTING AND OPERATING 317 NOTE: On four-wheel drive vehicles be sure that the WARNING! (Continued) transfer case is in a drive position. vehicle could accelerate quickly forward or in re- When exiting the vehicle, always: verse. You could lose control of the vehicle and hit someone or something.
Page 320 318 STARTING AND OPERATING The following indicators should be used to ensure that you WARNING! (Continued) have engaged the transmission into the PARK position: of reasons. A child or others could be seriously or • When shifting into PARK, pull the gear selector toward fatally injured.
Page 321 STARTING AND OPERATING 319 When frequent transmission shifting occurs (such as when WARNING! operating the vehicle under heavy loading conditions, in hilly terrain, traveling into strong head winds, or while Do not coast in NEUTRAL and never turn off the towing a heavy trailer), use the Electronic Range Select ignition to coast down a hill.
Page 322 320 STARTING AND OPERATING climbing a grade), or shifting to NEUTRAL (when stopped Limp Home Mode allows the vehicle to be driven to an in heavy traffic) can help to reduce this excess heat authorized dealer for service without damaging the trans- generation.
Page 323 STARTING AND OPERATING 321 Electronic Range Select (ERS) Operation The Electronic Range Select (ERS) shift control allows the driver to limit the highest available gear when the trans- mission is in DRIVE. For example, if you set the transmis- sion gear limit to 4 (fourth gear), the transmission will not shift above fourth gear, but will shift through the lower gears normally.
Page 324 322 STARTING AND OPERATING • Vehicle speed is sufficiently high. NOTE: To select the proper gear position for maximum deceleration (engine braking), simply push and hold the • The TOW/HAUL switch has not been activated. ERS (-) switch. The transmission will shift to the range •...
Page 325 STARTING AND OPERATING 323 WARNING! Do not use the “TOW/HAUL” feature when driving in icy or slippery conditions. The increased engine brak- ing can cause the rear wheels to slide, and the vehicle to swing around with the possible loss of vehicle control, which may cause an accident possibly result- ing in personal injury or death.
Page 326: Four-Wheel Drive Operation - If Equipped
324 STARTING AND OPERATING transmission is not shifting properly when cold. This is For additional information on the appropriate use of each normal. Using the Electronic Range Select (ERS) shift transfer case mode position, see the information below: control, when the transmission is sufficiently warm, will demonstrate that the transmission is able to shift into Two-Wheel Drive High Range —...
Page 327 STARTING AND OPERATING 325 This transfer case is intended to be driven in the 2H When operating your vehicle in 4L, the engine speed is position for normal street and highway conditions such as approximately three times that of the 2H or 4H positions at dry, hard surfaced roads.
Page 328 326 STARTING AND OPERATING 2H Or 4H To 4L WARNING! NOTE: When shifting into or out of 4L some gear noise You or others could be injured or killed if you leave the may be heard. This noise is normal and is not detrimental vehicle unattended with the transfer case in the NEU- to the vehicle or occupants.
Page 329: Electronically Shifted Transfer Case (Four-Position Switch) - If Equipped
STARTING AND OPERATING 327 • Shifting into or out of 4L is possible with the vehicle completely stopped, however difficulty may occur due to the mating clutch teeth not being properly aligned. Several attempts may be required for clutch teeth align- ment and shift completion to occur.
Page 330 328 STARTING AND OPERATING For additional information on the appropriate use of each WARNING! transfer case mode position, see the information below: You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the NEU- Rear Wheel Drive High Range —...
Page 331 STARTING AND OPERATING 329 The 4WD LOCK and 4WD LOW positions are designed for If One Or More Of The Following Shift Conditions Are loose, slippery road surfaces only. Driving in the 4WD Not Met: LOCK and 4WD LOW positions on dry hard surfaced 1.
Page 332 330 STARTING AND OPERATING Shifting Procedure WARNING! NOTE: Always engage the parking brake when powering • If any of the requirements to select a new transfer case down the vehicle if the “SVC 4WD Warning Light” is position have not been met, the transfer case will not illuminated.
Page 333 STARTING AND OPERATING 331 the transfer case will engage/disengage faster if you mo- 2. Shift the transmission into NEUTRAL. mentarily release the accelerator pedal after turning the 3. While still rolling, rotate the transfer case control switch control switch. If the vehicle is stopped, the ignition switch to the desired position.
Page 334: Electronically Shifted Transfer Case (Five-Position Switch) - If Equipped
332 STARTING AND OPERATING • Four-Wheel Drive Automatic High Range (4WD AUTO) be operable. If the ignition switch is not in the ON position, the shift will not take place and no position • Four-Wheel Drive Lock High Range (4WD LOCK) indicator lights will be on or flashing.
Page 335 STARTING AND OPERATING 333 4WD LOW loss of traction. Because the front axle is engaged, this mode will result in lower fuel economy than the 2WD Four-Wheel Drive Low Range — This range provides low mode. speed four-wheel drive. It maximizes torque to the front driveshaft, forcing the front and rear wheels to rotate at the When additional traction is required, the transfer case 4WD same speed.
Page 336 334 STARTING AND OPERATING Transfer Case Position Indicator Lights NOTE: Before retrying a selection, make certain that all the necessary requirements for selecting a new transfer case The Transfer Case Position Indicator Lights (4WD, 4LOW, position have been met. To retry the selection, turn the and 4WD AUTO) are located in the instrument cluster and control switch back to the current position, wait five indicate the current and desired transfer case selection.
Page 337 STARTING AND OPERATING 335 When operating your vehicle in 4WD LOW, the engine Shifting Procedure speed is approximately three times that of the 2WD, 4WD NOTE: AUTO or 4WD LOCK positions at a given road speed. Take • If any of the requirements to select a new transfer case care not to overspeed the engine and do not exceed 25 mph position have not been met, the transfer case will not (40 km/h).
Page 338: Four-Position Electronically Shifted Transfer Case (Eight Speed Transmission Only) - If Equipped
336 STARTING AND OPERATING Four-Position Electronically Shifted Transfer Case • Four-Wheel Drive Low Range (4WD LOW) (Eight Speed Transmission Only) — If Equipped • Neutral (NEUTRAL) This is an electronic shift transfer case and is operated by For additional information on the appropriate use of each the 4WD Control Switch (Transfer Case Switch), which is transfer case mode position, see the information below: located on the instrument panel.
Page 339 STARTING AND OPERATING 337 NEUTRAL (N) NOTE: The transfer case NEUTRAL button is located in the center of the 4WD Control Switch and is pushed by Neutral — This range disengages both the front and rear using a ballpoint pen or similar object. The transfer case driveshafts from the powertrain.
Page 340 338 STARTING AND OPERATING If One Or More Of The Following Shift Conditions Are WARNING! (Continued) Not Met: illuminated. Not engaging the parking brake may 1. The indicator light for the current position will remain ON. allow the vehicle to roll which may cause personal injury or death.
Page 341: Five-Position Electronically Shifted Transfer Case (Eight Speed Transmission Only) - If Equipped
STARTING AND OPERATING 339 Shifting Procedure WARNING! NOTE: • You or others could be injured or killed if you leave • If any of the requirements to select a new transfer case the vehicle unattended with the transfer case in the position have not been met, the transfer case will not NEUTRAL (N) position without first fully engaging shift.
Page 342 340 STARTING AND OPERATING For additional information on the appropriate use of each transfer case mode position, see the information below: Rear-Wheel Drive High Range — This range is for normal street and highway driving on dry hard surfaced roads. 4WD AUTO Four-Wheel Drive Auto High Range —...
Page 343 STARTING AND OPERATING 341 same speed. This range provides additional traction and When additional traction is required, the transfer case 4WD maximum pulling power for loose, slippery road surfaces LOCK and 4WD LOW positions can be used to maximize only. Do not exceed 25 mph (40 km/h). torque to the front driveshaft, forcing the front and rear wheels to rotate at the same speed.
Page 344 342 STARTING AND OPERATING indicate the current and desired transfer case selection. find the shift requirements, refer to the Shifting Procedure When you select a different transfer case position, the for your transfer case, located in this section. indicator lights will do the following: The “SVC 4WD Warning Light”...
Page 345 STARTING AND OPERATING 343 Proper operation of four-wheel drive vehicles depends on WARNING! (Continued) tires of equal size, type and circumference on each wheel. indicates PARK (P) without blinking. Ensure that the Any difference in tire size can cause damage to the vehicle is completely stopped, and the PARK posi- drivetrain.
Page 346: Air Suspension System (1500 Models) - If Equipped
344 STARTING AND OPERATING AIR SUSPENSION SYSTEM (1500 MODELS) — IF NOTE: The vehicle will automatically enter Aero Mode EQUIPPED when the vehicle speed remains between 62 mph (100 km/h) and 66 mph (106 km/h) for greater than 20 seconds or if the Description vehicle speed exceeds 66 mph (106 km/h).
Page 347 STARTING AND OPERATING 345 • Off-Road 2 (OR2) (Raises the vehicle approximately 66 mph (106 km/h). The vehicle will return to NRH from 2 in (51 mm)) – This position is intended for off-roading Aero Mode if the vehicle speed remains between 30 mph use only where maximum ground clearance is required.
Page 348 346 STARTING AND OPERATING in Entry/Exit or drive the vehicle over 15 mph This system uses a lifting and lowering pattern which (24 km/h). Entry/Exit mode may not be available due to keeps the headlights from incorrectly shining into oncom- vehicle payload, an instrument cluster message will be ing traffic.
Page 349: Air Suspension Modes
STARTING AND OPERATING 347 NOTE: This mode is intended to be enabled with engine WARNING! (Continued) running. injury or damage to the system, see your authorized Transport Mode dealer for service. For towing your vehicle with four wheels off the road, the Air Suspension Modes air suspension system has a feature which will put the vehicle into Entry/Exit height and disable the automatic...
Page 350: Instrument Cluster Display Messages
348 STARTING AND OPERATING Operation Protection Strategy In order to “protect” the air suspension system, the vehicle will disable load leveling as required (suspension over- loaded, battery charge low, etc.). Load leveling will auto- matically resume as soon as system operation requirements are met.
Page 351 STARTING AND OPERATING 349 flashing, the highest flashing indicator lamp is the position Automatic height changes will occur based on vehicle the system is working to achieve. When lowering, if speed and the current vehicle height. The indicator lamps multiple indicators are flashing, the lowest solid indicator and instrument cluster display messages will operate the lamp is the position the system is working to achieve.
Page 352: Air Suspension System
350 STARTING AND OPERATING • Transport Mode – No indicator lamps will be illumi- nated. Transport Mode is disabled by driving the ve- hicle. • Tire/Jack Mode – Indicator lamps 3 and 6 will be illuminated. Tire/Jack Mode is disabled by driving the vehicle.
Page 353 STARTING AND OPERATING 351 • Normal Ride Height (NRH) – This is the standard remains between 62 mph (100 km/h) and 66 mph position of the suspension and is meant for normal (106 km/h) for greater than 20 seconds or if the vehicle driving.
Page 354 352 STARTING AND OPERATING below 15 mph (24 km/h) the vehicle height will begin to This system uses a lifting and lowering pattern which lower. If the vehicle speed remains between 15 mph keeps the headlights from incorrectly shining into oncom- (24 km/h) and 25 mph (40 km/h) for greater than 60 ing traffic.
Page 355: Air Suspension Modes
STARTING AND OPERATING 353 NOTE: This mode is intended to be enabled with engine WARNING! (Continued) running. injury or damage to the system, see your authorized Transport Mode dealer for service. For towing your vehicle with four wheels off the road, the Air Suspension Modes air suspension system has a feature which will put the vehicle into Entry/Exit height and disable the automatic...
Page 356: Instrument Cluster Display Messages
354 STARTING AND OPERATING Operation Protection Strategy In order to “protect” the air suspension system, the vehicle will disable load leveling as required (suspension over- loaded, battery charge low, etc.). Load leveling will auto- matically resume as soon as system operation requirements are met.
Page 357 STARTING AND OPERATING 355 Pushing the “Up” button once will move the suspension • Normal Ride Height (NRH) – Indicator lamps 3, 4 and 5 one position higher from the current position, assuming all will be illuminated when the vehicle is in NRH. conditions are met (i.e.
Page 358: Air Suspension System (2500/3500 Models)
356 STARTING AND OPERATING AIR SUSPENSION SYSTEM (2500/3500 MODELS) — Normal Ride Height (NRH) – This is the standard position IF EQUIPPED of the suspension and is meant for normal driving. It will automatically adjust to maintain the rear ride height as Description conditions change.
Page 359: Air Suspension Modes
STARTING AND OPERATING 357 NOTE: disabled. This mode is intended to be enabled with engine running. Refer to “Instrument Cluster Display” in “Getting • Most 3500 models will not lower to Alternate Trailer To Know Your Instrument Panel” or “Uconnect Settings” in Height (ATH) when unloaded.
Page 360: Instrument Cluster Display Messages
358 STARTING AND OPERATING Operation To Know Your Instrument Panel” or “Uconnect Settings” in “Multimedia” if equipped with a touch screen radio for Pushing the Alternate Trailer Height (ATH) button once further information. while at Normal Ride Height (NRH), will lower the vehicle to Alternate Trailer Height (ATH) and will illuminate the NOTE: This mode is intended to be enabled with engine LED.
Page 361: Axle Locker System - Power Wagon Models Only (If Equipped)
STARTING AND OPERATING 359 AXLE LOCKER SYSTEM — POWER WAGON MODELS ONLY (IF EQUIPPED) This vehicle is equipped with electronically locking front and rear differentials. These differentials, when engaged, mechanically lock together the axle shafts forcing the wheels to spin at an equal rate. This allows the vehicle to maintain its momentum and prevents it from becoming stuck.
Page 362 360 STARTING AND OPERATING The locking axles are controlled by the axle locker switch. NOTE: Left to right wheel speed difference may be neces- sary to allow the axle to fully lock. If the indicator light is The switch has three positions: flashing after placing the switch in the REAR LOCK or •...
Page 363: Stabilizer/Sway Bar System - Power Wagon Only
STARTING AND OPERATING 361 NOTE: The axle lockers could be torque locked due to side to side loads on the axle. Driving slowly while turning the steering wheel from a left hand turn to a right hand turn or driving in REVERSE for a short distance may be required to release the torque lock and unlock the axles.
Page 364: Safe Off-Road Driving - Power Wagon Only
362 STARTING AND OPERATING To return to the On-Road mode; push the left hand On WARNING! (Continued) Road stabilizer/sway bar button. enhances vehicle stability and assists in maintaining control of the vehicle. The system monitors vehicle WARNING! speed and will attempt to reconnect the stabilizer bar If the stabilizer/sway bar will not return to On-Road at speeds over 18 mph (29 km/h).
Page 365 STARTING AND OPERATING 363 The National Forest Service, Bureau of Land Management, are safe from water ingestion. This vehicle has high water or local Department of Natural Resources are a wealth of fording characteristics with the ability to cross a pool of information and usually have maps with marked trails.
Page 366: Driving In Snow, Mud And Sand
364 STARTING AND OPERATING and ice. Every surface has a different effect on your When To Use Low Range vehicle’s steering, handling and traction. Controlling your When driving off-road, shift into 4LO (Low Range) for vehicle is one of the keys to successful off-road driving, so additional traction or to improve handling and control on always keep a firm grip on the steering wheel and maintain slippery or difficult terrain.
Page 367 STARTING AND OPERATING 365 stop, try turning your steering wheel no more than a ¼ • Sand – Soft sand is very difficult to travel through with turn quickly back and forth, while still applying throttle. full tire pressure. When crossing soft sandy spots in a This will allow the tires to get a fresh bite and help trail maintain your vehicle’s momentum and do not maintain your momentum.
Page 368: Crossing Obstacles (Rocks And Other High Points)
366 STARTING AND OPERATING Crossing Obstacles (Rocks And Other High Points) safe distance in front of you where they can see the obstacle, watch your tires and undercarriage, and guide While driving off road, you will encounter many types of you through.
Page 369 STARTING AND OPERATING 367 large obstacle with steep sides at an angle great enough to CAUTION! put the vehicle at risk of a rollover. If you get caught in a rut, dig a small trench to the right or left at a 45-degree Do not attempt to cross a log with a greater diameter angle ahead of the front tires.
Page 370: Hill Climbing
368 STARTING AND OPERATING Hill Climbing into a steep grade, the abrupt change of grade could cause you to lose control. If the front end begins to Hill climbing requires good judgment and a good under- bounce, ease off the throttle slightly to bring all four tires standing of your abilities and your vehicle’s limitations.
Page 371 STARTING AND OPERATING 369 Is it a straight descent? Is there plenty of distance at the WARNING! base of the hill to regain control if the vehicle descends too fast? If you feel confident in your ability to proceed Driving across an incline increases the risk of a roll- then make sure you are in 4LO (Low Range) with the over, which may result in severe injury.
Page 372: Driving Through Water
370 STARTING AND OPERATING Driving Through Water CAUTION! (Continued) Extreme care should be taken crossing any type of water. too fast or through too deep of water. Water can cause Water crossings should be avoided if possible and only be permanent damage to engine, driveline or other ve- attempted when necessary, in a safe responsible manner.
Page 373 STARTING AND OPERATING 371 water depth, approach angle, and bottom condition. the water is deep enough to push on the large surface Murky or muddy water holes are where you want to area of the vehicle’s body. Before you proceed determine hook up tow straps prior to entering.
Page 374 372 STARTING AND OPERATING start high and lower it as required. Remember you must damage during the recovery process? Answering these return the tires to normal air pressure before driving on questions will help you determine the best method of road or at highway conditions.
Page 375 STARTING AND OPERATING 373 each shift. During this process, for additional traction, requires coordination between the two drivers. Good try turning your steering wheel quickly left and right no communication and line of sight are required for a safe more than a ¼ turn. If you are stuck in mud, sand, or recovery.
Page 376 374 STARTING AND OPERATING around its base and hook the cable to the strap. If it is WARNING! another vehicle, then place that vehicle in PARK and block the front tires. If you cannot find an anchor point within Never use tow straps with end hooks or link two straps reach try using your spare tire by burying it.
Page 377 STARTING AND OPERATING 375 After Driving Off-Road WARNING! Off-road operation puts more stress on your vehicle than Abrasive material in any part of the brakes may cause does most on-road driving. After going off-road, it is excessive wear or unpredictable braking. You might always a good idea to check for damage.
Page 378 376 STARTING AND OPERATING WINCH USAGE — POWER WAGON ONLY (IF driving and cornering, the limited-slip unit performs simi- EQUIPPED) larly to a conventional differential. On slippery surfaces, however, the differential delivers more of the driving effort Things To Know Before Using Your Winch to the rear wheel having the better traction.
Page 379 STARTING AND OPERATING 377 Low Voltage Interrupt CAUTION! Your winch is equipped with a device that will interrupt Be certain the anchor will withstand the load required winch function if the vehicle charging system voltage to tension the wire rope. drops to a low level.
Page 380 378 STARTING AND OPERATING Understanding The Features Of Your Winch Winch Components...
Page 381 STARTING AND OPERATING 379 1. Motor: The winch motor is powered by the vehicle 7. Remote Control: The remote control provides the inter- charging system and features a thermal protection face between the winch operator and the winch. The switch that automatically stops motor function in the remote control provides the ability to power the winch power-in direction if the motor gets too hot.
Page 382 380 STARTING AND OPERATING Winch Accessories Clevis/D-Shackles: The D-Shackle is a The following accessories are necessary to attach the winch safe means of connecting the looped to anchors, change direction of pull, and for safe winching. ends of cables, straps and snatch blocks. The shackle’s pin is threaded to allow easy removal.
Page 383 STARTING AND OPERATING 381 Operating Your Winch WARNING! (Continued) • Never wrap wire rope back onto itself. Always use a WARNING! choker chain, wire choker rope or tree trunk protec- Failure to observe any of these warnings regarding tor on the anchor. proper winch usage may result in severe injury.
Page 384 382 STARTING AND OPERATING General Information CAUTION! (Continued) Practice using your winch before you get stuck. Some key Techniques, in order to understand your winch and points to remember when using your winch are: the winching operation. • Always inspect winch installation and wire rope •...
Page 385 STARTING AND OPERATING 383 1. Inspect the winch, winch mount, and wire rope for 3. Disengage the clutch to allow free spooling of the winch damage. Do not use the winch if the mount is loose or drum, rotate the clutch lever on the winch to disengage. rope shows excessive wear or damage.
Page 386 384 STARTING AND OPERATING 4. Free the winch hook and attach the hook strap. Free the 5. Pull the wire to the anchor point. Pull out enough wire winch hook from its anchor point. Attach the hook strap rope to reach your anchor point. Be sure to keep a to the hook (if not attached).
Page 387 STARTING AND OPERATING 385 6. Secure to the anchor point. Once you have established NOTE: How to choose an anchor point: A secure anchor your anchor point, secure the tree-trunk protector or is critical to winching operations. An anchor must be choker-chain around the object.
Page 388 386 STARTING AND OPERATING 7. Attach the Clevis/D-shackle and Tree Trunk Protector. choose to control the winch from inside your vehicle, Attach the shackle to the two ends of the strap or chain always pass the remote through a window to avoid and through the hook loop, being careful not to over pinching the cord in the door.
Page 389 STARTING AND OPERATING 387 12. Check wire rope. The wire rope should be neatly wound around the spooling drum. Improper winding can cause damage to the wire rope. Pulling Wire Rope Under Tension 11. Check your anchor. Make sure all connections are secured and free of debris before continuing with the winching procedure.
Page 390 388 STARTING AND OPERATING 13. Establish no people zones: Make your intentions clear. Be sure that everyone in the immediate vicinity surrounding the winching operation is completely aware of your intentions before you pull. Declare where the spectators should not stand - never behind or in front of the vehicle and never near the wire rope or snatch block.
Page 391 STARTING AND OPERATING 389 14. Begin winching. With the winching vehicles engine on NOTE: and light tension already on the wire rope, begin • Avoid overheating the winch motor. For extended winching slowly and steadily. Be sure that the wire winching, stop at reasonable intervals to allow the rope is winding evenly and tightly around the spooling winch motor to cool down.
Page 392 390 STARTING AND OPERATING 16. Disconnect the wire rope, and disconnect from the NOTE: How to spool under no load: Arrange the remote anchor. control lead so it cannot be caught in the winch. Arrange the wire rope so it will not kink or tangle when spooled. Be 17.
Page 393 STARTING AND OPERATING 391 straight-line pulling situation. You will have to assess what technique is correct for your situation. Think safety at all times. How To Change The Pulling Direction Hook In Stored Position 19. Disconnect the remote control. Disconnect the remote control cord from the control box and store in a clean and dry place.
Page 394 392 STARTING AND OPERATING you to change your pulling direction while still allowing to double line out more wire rope. This decreases the the wire rope to be at 90° to wind properly onto the number of layers of wire rope on the drum, and increases spooling drum.
Page 395 STARTING AND OPERATING 393 If the Steering icon is flashing, it indicates that the vehicle • If the condition persists, see your authorized dealer for needs to be taken to the dealer for service. It is likely the service. vehicle has lost power steering assistance. Hydraulic Power Steering —...
Page 396 394 STARTING AND OPERATING CAUTION! WARNING! Prolonged operation of the steering system at the end Fluid level should be checked on a level surface and of the steering wheel travel will increase the steering with the engine off to prevent injury from moving fluid temperature and it should be avoided when parts and to ensure accurate fluid level reading.
Page 397 STARTING AND OPERATING 395 SPEED CONTROL NOTE: In order to ensure proper operation, the Speed Control System has been designed to shut down if multiple When engaged, the Speed Control takes over accelerator speed control functions are operated at the same time. If operations at speeds greater than 25 mph (40 km/h).
Page 398 396 STARTING AND OPERATING To Set A Desired Speed • If the button is continually pushed, the set speed will continue to increase until the button is released, then the Turn the Speed Control on. When the vehicle has reached new set speed will be established.
Page 399 STARTING AND OPERATING 397 • If the button is continually pushed, the set speed will WARNING! continue to decrease until the button is released, then the new set speed will be established. Speed Control can be dangerous where the system cannot maintain a constant speed.
Page 400 398 STARTING AND OPERATING PARKSENSE REAR PARK ASSIST — IF EQUIPPED the sensors’ field of view. The sensors can detect obstacles from approximately 18 inches (45 cm) up to 79 inches The ParkSense Rear Park Assist system provides visual and (200 cm) from the rear fascia/bumper in the horizontal audible indications of the distance between the rear fascia direction, depending on the location, type and orientation of...
Page 401 STARTING AND OPERATING 399 The system will indicate a detected obstacle by showing a single arc in the left and/or right rear regions based on the object’s distance and location relative to the vehicle. If an object is detected in the left and/or right rear region, the display will show a single solid arc in the left and/or right rear region and the system will produce a tone.
Page 402 400 STARTING AND OPERATING Fast Tone Continuous Tone The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: WARNING ALERTS Rear Distance Greater than...
Page 403 STARTING AND OPERATING 401 None 4th Solid Solid Flashing Flashing Radio Volume Reduced NOTE: ParkSense will reduce the volume of the radio, if moved to REVERSE and the system is disabled, the instru- on, when the system is sounding an audio tone. ment cluster display will show the “PARKSENSE OFF”...
Page 404 402 STARTING AND OPERATING Service The ParkSense Rear Park Assist System Cleaning The ParkSense System During vehicle start up, when the ParkSense Rear Park Clean the ParkSense sensors with water, car wash soap and Assist System has detected a faulted condition, the instru- a soft cloth.
Page 405 STARTING AND OPERATING 403 • Clean the ParkSense sensors regularly, taking care not to WARNING! scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. • Drivers must be careful when backing up even when Failure to do so can result in the system not working using ParkSense.
Page 406 404 STARTING AND OPERATING ParkSense will retain the last system state (enabled or CAUTION! disabled) from the last ignition cycle when the ignition is changed to the ON/RUN position. • ParkSense is only a parking aid and it is unable to recognize every obstacle, including small obstacles.
Page 407 STARTING AND OPERATING 405 ParkSense Display The six ParkSense sensors, located in the front fascia/ bumper, monitor the area in front of the vehicle that is The warning display will turn on indicating the system within the sensors’ field of view. The sensors can detect status when the vehicle is in REVERSE or when the vehicle obstacles from approximately 12 inches (30 cm) up to 47 is in DRIVE and an obstacle has been detected.
Page 408 406 STARTING AND OPERATING The vehicle is close to the obstacle when the display shows one flashing arc and sounds a continuous tone. The follow- ing chart shows the warning alert operation when the system is detecting an obstacle: WARNING ALERTS Rear Distance Greater than 79-45 inches...
Page 409 STARTING AND OPERATING 407 Adjustable Chime Volume Settings REAR PARKSENSE OFF message for five seconds, fol- lowed by a vehicle graphic with OFF in the correspond- The Front and Rear chime volume settings are program- ing side. This vehicle graphic will be displayed for as long mable.
Page 410 408 STARTING AND OPERATING a faulted condition, the instrument cluster display will snow, ice, mud, dirt or other obstruction and then cycle the display a PARKSENSE UNAVAILABLE WIPE REAR SEN- ignition. If the message continues to appear see your SORS , PARKSENSE UNAVAILABLE WIPE FRONT SEN- authorized dealer.
Page 411 STARTING AND OPERATING 409 you turn Front or Rear ParkSense off, it remains off until misinterpreting a close obstacle as a sensor problem, you turn it on again, even if you cycle the ignition key. causing the “PARKSENSE UNAVAILABLE SERVICE REQUIRED”...
Page 412 410 STARTING AND OPERATING PARKVIEW REAR BACK UP CAMERA — IF WARNING! (Continued) EQUIPPED hitch ball will be much closer to the obstacle than the Your vehicle may be equipped with the ParkView Rear rear fascia when the loudspeaker sounds the con- Back Up Camera that allows you to see a image of the rear tinuous tone.
Page 413 STARTING AND OPERATING 411 Whenever the Rear View Camera image is activated A touchscreen button X to disable display of the camera through the Backup Camera button in the Controls image is made available when the vehicle is not in RE- menu, a display timer for the image is initiated.
Page 414 412 STARTING AND OPERATING WARNING! CAUTION! (Continued) that the driver look frequently over his/her shoulder Drivers must be careful when backing up even when when using ParkView. using the ParkView Rear Back Up Camera. Always check carefully behind your vehicle, and be sure to NOTE: If snow, ice, mud, or any foreign substance builds check for pedestrians, animals, other vehicles, obstruc- up on the camera lens, clean the lens, rinse with water, and...
Page 415 STARTING AND OPERATING 413 REFUELING THE VEHICLE — GAS ENGINE WARNING! The fuel filler cap (gas cap) is located behind the fuel filler • Never have any smoking materials lit in or near the door, on the left side of the vehicle. Open the fuel door and vehicle when the gas cap is removed or the tank is remove the fuel cap by turning it counter-clockwise.
Page 416 414 STARTING AND OPERATING Loose Fuel Filler Cap Message NOTE: • When the fuel nozzle “clicks” or shuts off, the fuel tank is full. If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, • Tighten the gas cap until you hear a “clicking” sound. or damaged, a loose gascap indicator will dis- This is an indication that the gas cap is tightened play in the instrument cluster telltale display...
Page 417 STARTING AND OPERATING 415 Gross Axle Weight Rating (GAWR) Curb Weight The GAWR is the maximum permissible load on the front The curb weight of a vehicle is defined as the total weight and rear axles. The load must be distributed in the cargo of the vehicle with all fluids, including vehicle fuel, at full area so that the GAWR of each axle is not exceeded.
Page 418 416 STARTING AND OPERATING Common Towing Definitions Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way The following trailer towing related definitions will assist the brakes operate. you in understanding the following information: Gross Vehicle Weight Rating (GVWR) CAUTION! The GVWR is the total allowable weight of your vehicle.
Page 419 STARTING AND OPERATING 417 Tongue Weight (TW) WARNING! The tongue weight is the downward force exerted on the If the gross trailer weight is 5,000 lbs (2,267 kg) or more, hitch ball by the trailer. You must consider this as part of it is recommended to use a weight-distributing hitch to the load on your vehicle.
Page 420 418 STARTING AND OPERATING hitches are the most popular on the market today and they WARNING! are commonly used to tow small and medium sized trailers. • An improperly adjusted weight distributing hitch system may reduce handling, stability and braking Weight-Distributing Hitch performance and could result in a collision.
Page 421 STARTING AND OPERATING 419 With Weight-Distributing Hitch (Correct) Improper Adjustment Of Weight-Distributing Hitch (Incorrect) Recommended Distribution Hitch Adjustment Towing With 1500 Air Suspension 1. Set air suspension to normal ride height. No action is required if already in normal ride height. NOTE: The vehicle must remain in the engine run position with all doors closed while attaching a trailer for proper leveling of the air suspension system.
Page 422 420 STARTING AND OPERATING 3. Under the instrument cluster or touch screen radio 7. Install and adjust the tension in the weight distributing settings, enable jack mode. Jack mode will be canceled bars per the manufacturers’ recommendations so that and procedure must be restarted if the vehicle is driven the height of the front fender is approximately (H2-H1)/ at speeds above 5mph (8 kmh).
Page 423 STARTING AND OPERATING 421 Towing With 2500/3500 Air Suspension 6. Preform a visual inspection of the trailer and weight distributing hitch to confirm manufacturers’ recommen- 1. Position the truck to be ready to connect to the trailer dations have been met. (do not connect the trailer).
Page 424 422 STARTING AND OPERATING 4. Measure the height of the top of the front wheel opening Fifth-Wheel Hitch on the fender to ground, this is height H2. The fifth-wheel hitch is a special high platform with a coupling that mounts over the rear axle of the tow vehicle 5.
Page 425 STARTING AND OPERATING 423 Trailer Towing Weights (Maximum Trailer Weight Trailer Hitch Type and Maximum Trailer Weight Ratings) Hitch Type Max. Trailer Weight / Max. Tongue Weight NOTE: For trailer towing information (maximum trailer weight ratings) refer to the following website addresses: Class III Bumper 5,000 lbs (2,268 kg) / Hitch - 1500 Model...
Page 426 424 STARTING AND OPERATING Consider the following items when computing the weight CAUTION! (Continued) on the rear axle of the vehicle: • Then, during the first 500 miles (805 km) that a trailer • The tongue weight of the trailer. is towed, do not drive over 50 mph (80 km/h) and do •...
Page 427 STARTING AND OPERATING 425 WARNING! (Continued) WARNING! (Continued) • When hauling cargo or towing a trailer, do not 2. GTW overload your vehicle or trailer. Overloading can 3. GAWR cause a loss of control, poor performance or damage to brakes, axle, engine, transmission, steering, sus- 4.
Page 428 426 STARTING AND OPERATING Towing Requirements — Trailer Brakes CAUTION! • Do not interconnect the hydraulic brake system or If the trailer weighs more than 1,000 lbs (453 kg) vacuum system of your vehicle with that of the trailer. loaded, it should have its own brakes and they should This could cause inadequate braking and possible per- be of adequate capacity.
Page 429 STARTING AND OPERATING 427 The trailer and the vehicle’s brake lamps will come on when either vehicle braking or manual trailer brakes are applied. Trailer Brake Status Indicator Light This light indicates the trailer electrical connection status. If no electrical connection is detected after the ignition is turned on, pushing the GAIN adjustment button or sliding the manual brake control lever will display the GAIN setting for 10 seconds and the “Trailer Brake Status Indi-...
Page 430 428 STARTING AND OPERATING towing conditions change. Changes to towing conditions 4. Push the UP or DOWN button on the steering wheel include trailer load, vehicle load, road conditions and until “TRAILER TOW” appears on the screen. weather. 5. Push the RIGHT arrow on the steering wheel to enter Adjusting GAIN “TRAILER TOW”.
Page 431 STARTING AND OPERATING 429 Repeat steps 8 and 9 until the GAIN setting is at a point just trailer wheel lockup may not be attainable even with the below trailer wheel lockup. If towing a heavier trailer, maximum GAIN setting of 10. Light Electric Heavy Electric Light EOH...
Page 432 430 STARTING AND OPERATING NOTE: NOTE: • An aftermarket controller may be available for use with • Disconnect trailer wiring connector from the vehicle trailers with air or electric-over-hydraulic trailer brake before launching a boat (or any other device plugged systems.
Page 433 STARTING AND OPERATING 431 Automatic Transmission The DRIVE range can be selected when towing. The transmission controls include a drive strategy to avoid frequent shifting when towing. However, if frequent shift- ing does occur while in DRIVE, select TOW/HAUL mode or select a lower gear range (using the Electronic Range Select (ERS) shift control).
Page 434 432 STARTING AND OPERATING frequent trailer towing. Refer to the “Maintenance Plan” Cooling System for the proper maintenance intervals. To reduce potential for engine and transmission overheat- ing, take the following actions: NOTE: Check the automatic transmission fluid level be- fore towing (6-speed automatic only).
Page 435 STARTING AND OPERATING 433 SNOWPLOW 2500/3500 Models Only Snowplow Prep Packages are available as a factory in- 1500 Models Only stalled option. These packages include components neces- NOTE: Do not use this model vehicle for snowplow sary to equip your vehicle with a snowplow. applications.
Page 436 434 STARTING AND OPERATING Before Plowing The loaded vehicle weight, including the snowplow sys- tem, all aftermarket accessories, driver, passengers, op- • Check the hydraulic system for leaks and proper fluid tions, and cargo, must not exceed either the Gross Vehicle level.
Page 437 STARTING AND OPERATING 435 Over The Road Operation With Snowplow Attached When plowing snow, to avoid transmission and drivetrain damage, the following precautions should be observed. The blade restricts air flow to the radiator and causes the • Operate with transfer case in 4LO when plowing small engine to operate at higher than normal temperatures.
Page 438 436 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Wheels OFF Two-Wheel Four-Wheel Drive Models The Ground Drive Models Flat Tow NONE See Instructions • Automatic transmission in PARK ALLOWED • Manual transmission in gear (NOT in NEUTRAL) •...
Page 439 STARTING AND OPERATING 437 Recreational Towing — Two-Wheel Drive Models CAUTION! DO NOT flat tow this vehicle. Damage to the drivetrain • Towing with the rear wheels on the ground will will result. cause severe transmission damage. Damage from Recreational towing (for two-wheel drive models) is al- improper towing is not covered under the New lowed ONLY if the rear wheels are OFF the ground.
Page 440 438 STARTING AND OPERATING Shifting Into NEUTRAL (N) CAUTION! (Continued) Use the following procedure to prepare your vehicle for damage. Tow with all four wheels either ON the recreational towing. ground, or OFF the ground (using a vehicle trailer). • Tow only in the forward direction. Towing this WARNING! vehicle backwards can cause severe damage to the transfer case.
Page 441 STARTING AND OPERATING 439 1. Bring the vehicle to a complete stop on level ground, 6. Release the parking brake. with the engine running. Firmly apply the parking 7. Shift the transmission into REVERSE. brake. 8. Release the brake pedal (and clutch pedal on manual 2.
Page 442 440 STARTING AND OPERATING NOTE: With electronic shift transfer case: Shifting Out Of NEUTRAL (N) • Steps 2 through 4 are requirements that must be met Use the following procedure to prepare your vehicle for before pushing the NEUTRAL (N) button, and must normal usage: continue to be met until the shift has been completed.
Page 443 STARTING AND OPERATING 441 NOTE: When shifting out of transfer case NEUTRAL (N), NOTE: With electronic shift transfer case: turning the engine OFF is not required, but may be helpful • Steps 3 and 4 are requirements that must be met before to avoid gear clash.
Page 444 442 STARTING AND OPERATING difference in the surface traction under the rear (driving) WARNING! (Continued) wheels. cause your vehicle to sink into deeper water. Further- more, flowing and/or rising water can carry your ve- WARNING! hicle away swiftly. Failure to follow this warning may Rapid acceleration on slippery surfaces is dangerous.
Page 445 STARTING AND OPERATING 443 WARNING! (Continued) CAUTION! (Continued) • Failure to follow these warnings may result in inju- may result in further damage. Such damage is not ries that are serious or fatal to you, your passengers, covered by the New Vehicle Limited Warranty. •...
Page 446 444 STARTING AND OPERATING • After extended operation in mud, sand, water, or similar After Driving Off-Road dirty conditions, have the radiator, fan, brake rotors, Off-road operation puts more stress on your vehicle than wheels, brake linings, and axle yokes inspected and does most on-road driving.
Page 447 IN CASE OF EMERGENCY CONTENTS HAZARD WARNING FLASHERS ... .447 JUMP STARTING ......502 ASSIST AND SOS MIRROR —...
Page 448 446 IN CASE OF EMERGENCY TOWING A DISABLED VEHICLE ... .510 ENHANCED ACCIDENT RESPONSE SYSTEM (EARS) .......514 ▫...
Page 449: Hazard Warning Flashers
IN CASE OF EMERGENCY 447 HAZARD WARNING FLASHERS ASSIST AND SOS MIRROR — IF EQUIPPED The Hazard Warning flasher switch is located on the upper switch bank just below the radio. Push the switch to turn on the Hazard Warning flasher.
Page 450 448 IN CASE OF EMERGENCY someone who can help. Roadside Assistance will know WARNING! (Continued) what vehicle you’re driving and its location. Additional SiriusXM Guardian features and applications in this fees may apply for roadside Assistance. vehicle. Only use Uconnect features and SiriusXM •...
Page 451 IN CASE OF EMERGENCY 449 3. Once a connection between the vehicle and a SOS NOTE: operator is made, the SOS Call system may transmit the • Your vehicle may be transmitting data as authorized following important vehicle information to a SOS op- by the subscriber.
Page 452 450 IN CASE OF EMERGENCY WARNING! (Continued) WARNING! (Continued) APPS AND SERVICES, AMONG OTHERS, WILL Emergency Services Agent. All occupants should exit NOT OPERATE. the vehicle immediately and move to a safe location. • Modifications to any part of the SOS Call system •...
Page 453 IN CASE OF EMERGENCY 451 • An In-Vehicle Audio message will state “Vehicle device • The SOS Call system software and/or hardware are requires service. Please contact your dealer.” damaged during a crash. • The vehicle battery loses power or becomes discon- WARNING! nected during a vehicle crash.
Page 454: Bulb Replacement
452 IN CASE OF EMERGENCY NOTE: Changes or modifications not expressly approved WARNING! (Continued) by the party responsible for compliance could void the Guardian services when it is safe to do so. Failure to do user’s authority to operate the equipment. so may result in an accident involving serious injury or death.
Page 455 IN CASE OF EMERGENCY 453 Exterior Bulbs Bulb Number Bulb Number Center High Mounted 921K Base Quad Headlamp – H11LL Stop Lamp (CHMSL) Low Beam Rear Cargo Lamp Base Quad Headlamp – 9005LL LED Center High LED (Serviced at autho- High Beam Mounted Stop Lamp rized dealer)
Page 456: Replacing Exterior Bulbs
454 IN CASE OF EMERGENCY Replacing Exterior Bulbs Base Quad / Premium Bi-Halogen: Low Beam Headlamp, High Beam Headlamp, Front Park And Turn — If Equipped 1. Open the hood. 2. Disconnect and isolate the negative battery cable. 3. Remove the six plastic push-in fasteners that secure the upper radiator seal to the grille support and both fender ledges.
Page 457 IN CASE OF EMERGENCY 455 CAUTION! • Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. • Always use the correct bulb size and type for replace- ment.
Page 458 456 IN CASE OF EMERGENCY the lamp housing from the two plastic snap post retain- CAUTION! ers in the outer box side panel. Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces.
Page 459 IN CASE OF EMERGENCY 457 2. Separate the connector holding the housing and wiring CAUTION! harness to the body. Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. 6.
Page 460 458 IN CASE OF EMERGENCY Cab Top Clearance Lamps — If Equipped 1. Remove the two screws from the top of the lamp. CHMSL Bulb And Socket CAUTION! Removing Rear Screw From Clearance Lamp Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces.
Page 461 IN CASE OF EMERGENCY 459 2. Rotate the bulb socket ¼ turn and pull it from the lamp 3. Pull the bulb straight from it’s socket and replace. assembly. Removing The Bulb From The Bulb Socket Removing Bulb Socket From Clearance Lamp...
Page 462 460 IN CASE OF EMERGENCY Rear Lamp Bar ID Marker (Dual Rear Wheels) — If Side Marker Lamps (Dual Rear Wheels) — If Equipped Equipped 1. Loosen the two screws and the housing to gain access to the bulb sockets. Side Marker Lamp Locations 1.
Page 463: Fuses
IN CASE OF EMERGENCY 461 FUSES Power Distribution Center The Power Distribution Center is located in the engine WARNING! compartment near the battery. This center contains car- tridge fuses, micro fuses, relays, and circuit breakers. A • When replacing a blown fuse, always use an appro- description of each fuse and component may be stamped priate replacement fuse with the same amp rating as on the inside cover, otherwise the cavity number of each...
Page 464 462 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description 60 Amp Yellow – Rad Fan – If Equipped 40 Amp Green – Compressor for Air Suspension – If Equipped 40 Amp Green – Antilock Brakes/Electronic Stability Control Pump 40 Amp Green –...
Page 465 IN CASE OF EMERGENCY 463 Cavity Cartridge Fuse Micro Fuse Description 20 Amp Blue – SCR – If Equipped (1500 LD Diesel) 30 Amp Pink (Cum- mins Diesel) 30 Amp Pink – Passenger Door Module 30 Amp Pink – Drive Train Control Module 20 Amp Blue –...
Page 466 464 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description 30 Amp Pink – Vehicle System Interface Module #2 – If Equipped 30 Amp Pink – Sunroof – If Equipped 30 Amp Pink – Rear Defroster – If Equipped 30 Amp Pink –...
Page 467 IN CASE OF EMERGENCY 465 Cavity Cartridge Fuse Micro Fuse Description – 20 Amp Yellow Adjustable Pedals – 15 Amp Blue Additional Diesel Content – If Equipped – 20 Amp Yellow Transmission – 20 Amp Yellow Spare Fuse – 10 Amp Red SCR Relay –...
Page 468 466 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description – 25 Amp Clear Amplifier – 10 Amp Red PCM – If Equipped – 20 Amp Yellow Fuel Transfer Pump (HD Only) – If Equipped – 20 Amp Yellow Brake Vacuum Pump Gas/Diesel –...
Page 469 IN CASE OF EMERGENCY 467 Cavity Cartridge Fuse Micro Fuse Description – 10 Amp Red Air Suspension – If Equipped / Trailer Tow / Steering Column Control Module – 15 Amp Blue Instrument Panel Cluster F90/F91 – 20 Amp Yellow Power Outlet (Rear Seats) Customer Selectable –...
Page 470: Jacking And Tire Changing
468 IN CASE OF EMERGENCY CAUTION! WARNING! (Continued) • Being under a jacked-up vehicle is dangerous. The • When installing the power distribution center cover, vehicle could slip off the jack and fall on you. You it is important to ensure the cover is properly posi- could be crushed.
Page 471 IN CASE OF EMERGENCY 469 If your vehicle is not equipped with a touchscreen, this feature can be activated through the instrument cluster display. Refer to “Instrument Cluster Display” in “Getting To Know Your Instrument Panel” for further information. Jack Location The jack and jack tools are stored under the front passenger seat.
Page 472 470 IN CASE OF EMERGENCY Remove the jack and tools by turning the wing bolt Release the tool bag straps from the jack and remove tools counterclockwise, remove the wing bolt and then slide the from bag. assembly out from under the seat. Jack And Tool Bag Jack And Tools (1500 Series)
Page 473 IN CASE OF EMERGENCY 471 There are two ways to assemble the tools: CAUTION! Assembled For Spare Tire Lowering/Raising • The lug wrench can only be attached to extension 2. • When attaching the tool to the winch mechanism be sure the large flared end opening on extension 4 is positioned correctly over the winch mechanism ad- justing nut.
Page 474 472 IN CASE OF EMERGENCY Assembled For Jack Operation Removing The Spare Tire 1. Remove the spare tire before attempting to jack up the truck. Attach the lug wrench to the extension tubes with the curved angle facing away from the vehicle. Insert the extension tube through the access hole between the lower tailgate and the top of the bumper and into the winch mechanism tube.
Page 475 IN CASE OF EMERGENCY 473 2. Rotate the lug wrench handle counterclockwise until 3. Pull the spare tire out from under the vehicle to gain the spare tire is on the ground with enough cable slack access to the spare tire retainer. to allow you to pull it out from under the vehicle.
Page 476 474 IN CASE OF EMERGENCY 4. Lift the spare tire with one hand to give clearance to tilt the retainer at the end of the cable. Pulling The Retainer Through The Center Of The Wheel NOTE: The winch mechanism is designed for use with the extension tubes only.
Page 477 IN CASE OF EMERGENCY 475 Jacking Instructions (1500 Series) WARNING! WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the Carefully follow these tire changing warnings to help road to avoid being hit when operating the jack or prevent personal injury or damage to your vehicle: changing the wheel.
Page 478 476 IN CASE OF EMERGENCY WARNING! (Continued) CAUTION! • If working on or near a roadway, be extremely Do not attempt to raise the vehicle by jacking on careful of motor traffic. locations other than those indicated in the Jacking •...
Page 479 IN CASE OF EMERGENCY 477 3. Placement of the jack is critical: 4x2 Series Trucks Front Jacking Location There is a jack location indicator on the rear portion of the NOTE: Keep the jack and tools aligned with raising the lower control arm.
Page 480 478 IN CASE OF EMERGENCY When changing a front wheel, place the scissor jack under 4x4 Series Trucks Front Jacking Location the rear portion of the lower control arm as shown below. There is a jack location indicator on the rear portion of the lower control arm.
Page 481 IN CASE OF EMERGENCY 479 When changing a front wheel, place the scissor jack under the rear portion of the lower control arm as shown below. Rear Jacking Location Connect the extension tubes and lug wrench. 4X4 Front Jacking Location CAUTION! Rear Jacking Location Operate the jack using the extension with jack hook and the...
Page 482 480 IN CASE OF EMERGENCY WARNING! WARNING! Raising the vehicle higher than necessary can make the A loose tire or jack thrown forward in a collision or vehicle less stable. It could slip off the jack and hurt hard stop, could endanger the occupants of the vehicle. someone near it.
Page 483 IN CASE OF EMERGENCY 481 2. Lift the spare tire with one hand to give clearance to tilt WARNING! the retainer at the end of the cable and position it properly across the wheel opening. A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle.
Page 484 482 IN CASE OF EMERGENCY 3. Attach the lug wrench to the extension tubes with the 4. Rotate the lug wrench handle clockwise until the wheel curved angle facing away from the vehicle. Insert the is drawn into place against the underside of the vehicle. extension tubes through the access hole between the Continue to rotate until you feel the winch mechanism lower tailgate and the top of the bumper and into the...
Page 485 IN CASE OF EMERGENCY 483 Reinstalling The Jack And Tools (1500 Series) 3. Secure the tool bag straps to the jack. 1. Tighten the jack all the way down by turning the jack turn-screw counterclockwise until the jack is snug. 2.
Page 486 484 IN CASE OF EMERGENCY 4. Place the jack and tools in the storage position holding the jack by the jack turn-screw, slip the jack and tools under the seat so that the bottom slot engages into the fastener on the floor. Jack And Tools (1500 Series) WARNING! After using the jack and tools, always reinstall them in...
Page 487: Jacking And Tire Changing 2500 And 3500 Series Trucks
IN CASE OF EMERGENCY 485 Jacking And Tire Changing 2500 And 3500 Series Jack Location Trucks The jack and jack tools are stored under the front passenger seat. WARNING! Removal Of Jack And Tools (2500 And 3500 Series) • Do not attempt to change a tire on the side of the To access the jack and jack tools, you must remove the vehicle close to moving traffic.
Page 488 486 IN CASE OF EMERGENCY Remove the jack and tools by turning the wing bolt Remove the jack and tools from the bracket assembly. Turn counterclockwise, remove the wing bolt and then slide the the jack-turn-screw counterclockwise to release jack from assembly out from under the seat.
Page 489 IN CASE OF EMERGENCY 487 There are two ways to assemble the tools: CAUTION! (Continued) Assembled For Spare Tire Lowering/Raising positioned correctly over the winch mechanism ad- justing nut. • Damage to the lug wrench, extensions and winch mechanism may occur from improper tool assembly. Assembled For Jack Operation Assembled For Spare Tire Lowering/Raising 1 —...
Page 490 488 IN CASE OF EMERGENCY WARNING! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid acceleration or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury.
Page 491 IN CASE OF EMERGENCY 489 2. Rotate the lug wrench handle counterclockwise until the 3. Pull the spare tire out from under the vehicle to gain spare tire is on the ground with enough cable slack to access to the spare tire retainer. allow you to pull it out from under the vehicle.
Page 492 490 IN CASE OF EMERGENCY 4. Lift the spare tire with one hand to give clearance to tilt the retainer at the end of the cable. Pulling The Retainer Through The Center Of The Wheel NOTE: The winch mechanism is designed for use with the extension tubes only.
Page 493 IN CASE OF EMERGENCY 491 Jacking Instructions (2500 And 3500 Series) WARNING! WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the Carefully follow these tire changing warnings to help road to avoid being hit when operating the jack or prevent personal injury or damage to your vehicle: changing the wheel.
Page 494 492 IN CASE OF EMERGENCY WARNING! (Continued) • If working on or near a roadway, be extremely careful of motor traffic. • To assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground.
Page 495 IN CASE OF EMERGENCY 493 NOTE: If your vehicle is equipped with hub caps/wheel covers they must be removed before raising the vehicle off the ground. Refer to ”Hub Caps/Wheel Covers — If Equipped” in this section. Lug Wrench Adapter And Wrench Lug Wrench Adapter...
Page 496 494 IN CASE OF EMERGENCY 3. Placement of the jack is critical: Front Jacking Location When changing the front wheel, assemble the jack driver to the jack and connect the jack driver to the extension tubes. Place the jack under the axle as close to the tire as possible with the drive tubes extending to the front.
Page 497 IN CASE OF EMERGENCY 495 Rear Jacking Location CAUTION! When changing a rear wheel, assemble the jack driver to Before raising the wheel off the ground, make sure that the jack and connect the jack driver to the extension tubes. the jack will not damage surrounding truck parts and Place the jack under the axle between the spring and the adjust the jack position as required.
Page 498 496 IN CASE OF EMERGENCY 5. Remove the lug nuts and pull the wheel off. On single rear-wheel (SRW) trucks, install the spare wheel and lug nuts with the cone shaped end of the wheel nuts toward the wheel. On 3500 dual rear-wheel models (DRW) trucks, if the outer tire is being replaced then leave the inner wheel on the vehicle.
Page 499 IN CASE OF EMERGENCY 497 To Stow The Flat Or Spare WARNING! NOTE: Have the flat tire repaired or replaced immedi- A loose tire or jack thrown forward in a collision or ately. hard stop, could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the WARNING! places provided.
Page 500 498 IN CASE OF EMERGENCY Reinstalling The Retainer Pushing The Retainer Through The Center Of The Wheel And Positioning It 2. Lift the spare tire with one hand to give clearance to tilt 3. Attach the lug wrench to the extension tubes with the the retainer at the end of the cable and position it curved angle facing away from the vehicle.
Page 501 IN CASE OF EMERGENCY 499 Lug Wrench And Extension Tubes Assembled And In Rotating The Lug Wrench Handle Position NOTE: The winch mechanism is designed for use with the 4. Rotate the lug wrench handle clockwise until the wheel jack extension tube only. Use of an air wrench or other is drawn into place against the underside of the vehicle.
Page 502 500 IN CASE OF EMERGENCY turn-screw. Snap tools into bracket assembly clips. In- stall the jack into bracket assembly and turn the jack- turn-screw clockwise until jack is snug into bracket assembly. Jack Hold Down Fastener NOTE: Ensure that the jack and tool bracket assembly slides into the front hold down location.
Page 503 IN CASE OF EMERGENCY 501 4. Turn the wing bolt clockwise to secure to the floor pan. CAUTION! (Continued) Reinstall the plastic cover. the wheel if screwdriver type tools are used. A pulling motion, not a pry off motion, is recommended to remove the caps.
Page 504: Jump Starting
502 IN CASE OF EMERGENCY CAUTION! (Continued) WARNING! • The rear hub caps on the dual rear wheel has two Do not attempt jump starting if the battery is frozen. It pull off notches. Make sure that the hook of the jack could rupture or explode and cause personal injury.
Page 505 IN CASE OF EMERGENCY 503 WARNING! (Continued) • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive. Keep open flames or sparks away from the battery. 1. Apply the parking brake, shift the automatic transmis- sion into PARK and turn the ignition to LOCK.
Page 506: Jump Starting Procedure
504 IN CASE OF EMERGENCY Jump Starting Procedure 4. Connect the opposite end of the negative (-) jumper cable to a good engine ground (exposed metal part of WARNING! the discharged vehicle’s engine) away from the battery and the fuel injection system. Failure to follow this jump starting procedure could result in personal injury or property damage due to WARNING!
Page 507: If Your Engine Overheats
IN CASE OF EMERGENCY 505 6. Once the engine is started, remove the jumper cables in CAUTION! (Continued) the reverse sequence: in use (i.e., cellular devices, etc.). Eventually, if plugged Disconnecting The Jumper Cables in long enough without engine operation, the vehicle’s battery will discharge sufficiently to degrade battery 1.
Page 508: Gear Selector Override - 6-Speed
506 IN CASE OF EMERGENCY GEAR SELECTOR OVERRIDE — 6-SPEED to the radiator and aids in removing heat from the TRANSMISSION engine cooling system. If a malfunction occurs and the gear selector cannot be WARNING! moved out of the PARK position, you can use one of the following procedures to temporarily move the gear selec- You or others can be badly burned by hot engine tor.
Page 509: Center Console Gear Selector - If Equipped
IN CASE OF EMERGENCY 507 5. Insert the screwdriver or similar tool into the access hole, and push and hold the override release lever down. Gear Selector Override Access Port 6. Move the gear selector to the NEUTRAL position. 7. The vehicle may then be started in NEUTRAL. Gear Selector Override Access Cover Center Console Gear Selector —...
Page 510: Manual Park Release - 8 Speed
508 IN CASE OF EMERGENCY MANUAL PARK RELEASE — 8 SPEED TRANSMISSION WARNING! Always secure your vehicle by fully applying the parking brake before activating the Manual Park Re- lease. In addition, you should be seated in the driver’s seat with your foot firmly on the brake pedal when activating the Manual Park Release.
Page 511: Freeing A Stuck Vehicle
IN CASE OF EMERGENCY 509 5. While holding the locking tab in the disengaged posi- REVERSE (with automatic transmission) or SECOND tion, pull the tether strap to rotate the lever rearward, GEAR and REVERSE (with manual transmission), while until it locks in place pointing towards the driver’s seat. gently pressing the accelerator.
Page 512: Towing A Disabled Vehicle
510 IN CASE OF EMERGENCY WARNING! (Continued) CAUTION! (Continued) • Revving the engine or spinning the wheels too fast injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 may lead to transmission overheating and failure. It seconds continuously without stopping when you are can also damage the tires.
Page 513 IN CASE OF EMERGENCY 511 Towing Wheels 2WD Models 4WD Models Condition OFF The Ground Flat Tow NONE If transmission is operable: See instructions in “Recreational Tow- • Transmission in NEUTRAL ing” under “Starting and Operating” • 30 mph (48 km/h) max speed •...
Page 514: Two-Wheel Drive Models
512 IN CASE OF EMERGENCY If the transmission is not operable, or the vehicle must be CAUTION! towed faster than 30 mph (48 km/h) or farther than 15 miles (24 km) for 6–speed transmission, or 30 miles • Do not use sling type equipment when towing. (48 km) for 8–speed transmission, tow with the rear wheels Vehicle damage may occur.
Page 515: Emergency Tow Hooks - If Equipped
IN CASE OF EMERGENCY 513 Emergency Tow Hooks — If Equipped If flatbed equipment is not available, and the transfer case is operable, the vehicle may be towed (in the forward Your vehicle may be equipped with emergency tow hooks. direction, with ALL wheels on the ground), IF the transfer NOTE: For off-road recovery, it is recommended to use case is in NEUTRAL and the transmission is in PARK (for...
Page 516: Enhanced Accident Response System (Ears)
514 IN CASE OF EMERGENCY ENHANCED ACCIDENT RESPONSE SYSTEM (EARS) This vehicle is equipped with an Enhanced Accident Response System. Please refer to “Occupant Restraint Systems” in “Safety” for further information on the Enhanced Accident Re- sponse System (EARS) function. EVENT DATA RECORDER (EDR) This vehicle is equipped with an Event Data Recorder (EDR).
Page 517 SERVICING AND MAINTENANCE CONTENTS SCHEDULED SERVICING ....517 ▫ Air Conditioner Maintenance ....533 ▫...
Page 518 516 SERVICING AND MAINTENANCE ▫ Tire Safety Information ....558 STORING THE VEHICLE ....584 ▫...
Page 519: Scheduled Servicing
SERVICING AND MAINTENANCE 517 SCHEDULED SERVICING 1500 Models Only Your vehicle is equipped with an automatic oil change NOTE: Under no circumstances should oil change indicator system. The oil change indicator system will intervals exceed 10,000 miles (16,000 km), twelve months remind you that it is time to take your vehicle in for or 350 hours of engine run time, whichever comes first.
Page 520: Maintenance Plan
518 SERVICING AND MAINTENANCE Maintenance Plan Severe Duty All Models Required Maintenance NOTE: Change Engine Oil at 4,000 miles (6,500 km) or 350 hours of engine run time if the vehicle is operated in a Refer to the Maintenance Plan on the following pages for dusty and off road environment or is operated predomi- required maintenance.
Page 521 SERVICING AND MAINTENANCE 519 Mileage or time passed (which- ever comes first) Or Years: Or Kilometers: Additional Inspections Inspect the CV/Universal joints. Inspect front suspension, tie rod ends, and replace if necessary. 1500 Models: Inspect the front and rear axle sur- faces.
Page 522 520 SERVICING AND MAINTENANCE Mileage or time passed (which- ever comes first) Or Years: Or Kilometers: Inspect the brake linings, replace as necessary. Adjust parking brake as necessary. Inspect transfer case fluid. Additional Maintenance Replace cabin air filter. Replace engine air filter. Replace spark plugs.
Page 523 SERVICING AND MAINTENANCE 521 Mileage or time passed (which- ever comes first) Or Years: Or Kilometers: Change automatic transmission fluid and filter(s) (six-speed auto- matic only). Inspect the transfer case fluid, change for any of the following: police, taxi, fleet, or frequent trailer towing.
Page 524: Heavy Duty Use Of The Vehicle
522 SERVICING AND MAINTENANCE WARNING! (Continued) • Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and performance. This could cause an accident. Heavy Duty Use Of The Vehicle Change engine oil at 4,000 miles (6,500 km) or 350 hours of engine run time if the vehicle is operated in a dusty and off road environment or is operated predominately at idle or only very low engine RPM’s.
Page 525: Engine Compartment
SERVICING AND MAINTENANCE 523 ENGINE COMPARTMENT 3.6L Engine 1 — Air Cleaner Filter 6 — Washer Fluid Reservoir 2 — Engine Oil Dipstick 7 — Power Distribution Center (Fuses) 3 — Engine Oil Fill 8 — Coolant Pressure Cap 4 — Brake Fluid Reservoir 9 —...
Page 526: L Engine
524 SERVICING AND MAINTENANCE 5.7L Engine 1 — Air Cleaner Filter 7 — Washer Fluid Reservoir 2 — Automatic Transmission Dipstick (6-Speed Trans Only) 8 — Power Distribution Center (Fuses) 3 — Engine Oil Fill 9 — Power Steering Fluid Reservoir (2500/3500 Models Only) 4 —...
Page 527: 6.4L Engine
SERVICING AND MAINTENANCE 525 6.4L Engine 1 — Coolant Pressure Bottle 6 — Battery 2 — Transmission Dipstick 7 — Power Distribution Center (Fuses) 3 — Engine Oil Fill 8 — Washer Solvent 4 — Engine Oil Dipstick 9 — Power Steering Fluid Reservoir 5 —...
Page 528: Checking Oil Level - Gas Engine
526 SERVICING AND MAINTENANCE Checking Oil Level — Gas Engine To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or To assure proper lubrication of your vehicle’s engine, the exceeds the temperature range of your climate. This rating engine oil must be maintained at the correct level.
Page 529: Dealer Service
SERVICING AND MAINTENANCE 527 WARNING! CAUTION! (Continued) negative post. Battery posts are marked positive (+) • Battery fluid is a corrosive acid solution and can and negative (-) and are identified on the battery burn or even blind you. Do not allow battery fluid to case.
Page 530: Engine Oil - Gas Engine
528 SERVICING AND MAINTENANCE 2500 – 3500 Models Only WARNING! NOTE: Under no circumstances should oil change You can be badly injured working on or around a intervals exceed 8,000 miles (13,000 km), twelve months or motor vehicle. Only do service work for which you 350 hours of engine run time, whichever comes first.
Page 531 SERVICING AND MAINTENANCE 529 American Petroleum Institute (API) Engine Oil The engine oil filler cap also shows the recommended Identification Symbol engine oil viscosity for your vehicle. For information on engine oil filler cap location, refer to “Engine Compart- ment” in “Servicing And Maintenance” for further infor- This symbol means that the oil has mation.
Page 532: Engine Oil Filter
530 SERVICING AND MAINTENANCE Engine Oil Viscosity (SAE Grade) — 6.4L Engine Materials Added To Engine Oil Use Mopar SAE 0W-40 engine oil approved to FCA Mate- The manufacturer strongly recommends against the addi- rial Standard MS-12633 such as Pennzoil Ultra equivalent tion of any additives (other than leak detection dyes) to the is recommended for all operating temperatures.
Page 533: Engine Air Cleaner Filter
SERVICING AND MAINTENANCE 531 Engine Air Cleaner Filter Engine Air Cleaner Filter Inspection and Replacement Refer to the “Maintenance Plan” in this section for the proper maintenance intervals. Inspect engine air cleaner filter for dirt and or debris, if you find evidence of either dirt or debris you should change NOTE: Be sure to follow the “Severe Duty Conditions”...
Page 534 532 SERVICING AND MAINTENANCE 6.4L Air Cleaner Filter Cover Open Air Cleaner Filter Assembly 1 — Clean Air Hose Clamp 1 — Air Cleaner Cover 2 — Spring Clips 2 — Air Cleaner Filter 2. Lift the air cleaner cover to access the air cleaner filter. 3.
Page 535: Air Conditioner Maintenance
SERVICING AND MAINTENANCE 533 2. Install the air cleaner cover onto the housing assembly locating tabs. 3. Latch the spring clips and lock the air cleaner cover to the housing assembly. Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season.
Page 536 534 SERVICING AND MAINTENANCE Refrigerant Recovery And Recycling — R–1234yf WARNING! (Continued) R–1234yf Air Conditioning Refrigerant is a hydrofluo- damage to the system, adding refrigerant or any roolefin (HFO) that is endorsed by the Environmental repair requiring lines to be disconnected should be Protection Agency and is an ozone-friendly substance with done by an experienced technician.
Page 537 SERVICING AND MAINTENANCE 535 The cabin air filter is located in the fresh air inlet behind the glove compartment. Perform the following procedure to replace the filter: 1. Open the glove compartment and remove all contents. 2. With the glove compartment door open, remove the glove compartment tension tether and tether clip by sliding the clip toward the face of the glove compart- ment door.
Page 538 536 SERVICING AND MAINTENANCE 5. Remove the filter cover by pushing in on the finger tabs on each end of the filter cover. Glove Compartment 1 — Glove Compartment Travel Stops Filter Cover 2 — Glove Compartment Tension Tether 3 — Glove Compartment Door 4.
Page 539 SERVICING AND MAINTENANCE 537 Finger Tabs Finger Tab 6. Remove the cabin air filter by pulling it straight out of the housing.
Page 540 538 SERVICING AND MAINTENANCE 8. Reinstall the glove compartment on the hinges. Cabin Air Filter 7. Install the cabin air filter with the arrow on the filter Glove Compartment Installation pointing toward the floor. When installing the filter 9. Pull the tension tether outward and reinstall the glove cover, press on each end until you hear an audible click.
Page 541: Front Driveshaft Lubrication - 2500/3500
SERVICING AND MAINTENANCE 539 Front Driveshaft Lubrication — 2500/3500 (Four-Wheel Drive Models Only) Lubricate the front driveshaft grease fitting at each oil change. Right Side Of Glove Compartment 1 — Glove Compartment Tension Tether 2 — Glove Compartment Travel Stop NOTE: Ensure the glove compartment door hinges and Front Drive Shaft Double Cardan Joint glove compartment travel stops are fully engaged.
Page 542: Accessory Drive Belt Inspection
540 SERVICING AND MAINTENANCE Accessory Drive Belt Inspection The grease fitting is located at the rear of the front driveshaft, near the centering mechanism of double cardan joint. Refer to the “Maintenance Plan” for the proper WARNING! maintenance intervals. Use Mopar Type MS-6560 (lithium- •...
Page 543: Body Lubrication
SERVICING AND MAINTENANCE 541 • Noise (objectionable squeal, squeak, or rumble is heard or felt while drive belt is in operation) Some conditions can be caused by a faulty component such as a belt pulley. Belt pulleys should be carefully inspected for damage and proper alignment.
Page 544: Windshield Wiper Blades
542 SERVICING AND MAINTENANCE The external lock cylinders should be lubricated twice a The wiper blades and wiper arms should be inspected year, preferably in the Fall and Spring. Apply a small periodically, not just when wiper performance problems amount of a high quality lubricant, such as Mopar Lock are experienced.
Page 545 SERVICING AND MAINTENANCE 543 Windshield Wiper Arm Wiper Locking Assembly 1 — Wiper 1 — Wiper 2 — Locking Tab 2 — Locking Tab 3 — Wiper Arm 3. Tilt the lower end of the wiper blade away from the arm 2.
Page 546 544 SERVICING AND MAINTENANCE Wiper Disengaging Removing Wiper From Wiper Arm 1 — Locking Tab 1 — Wiper 2 — Wiper 2 — Locking Tab 3 — Release Tab 3 — Wiper Arm J Hook 4. Slide the wiper blade down towards the base of the 6.
Page 547: Exhaust System
SERVICING AND MAINTENANCE 545 3. Insert the receiver bracket on the wiper assembly into WARNING! the hook on the tip of the arm through the opening in the wiper blade under the locking tab. • Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless.
Page 548: Cooling System
546 SERVICING AND MAINTENANCE To minimize the possibility of catalytic converter damage: CAUTION! (Continued) • Do not interrupt the ignition when the transmission is in the event of engine malfunction, particularly involv- gear and the vehicle is in motion. ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly.
Page 549 SERVICING AND MAINTENANCE 547 appearance, the system should be drained, flushed and Selection Of Coolant refilled with fresh coolant. Check the front of the A/C Refer to “Fluids And Lubricants” in “Technical Specifica- condenser (if equipped) or radiator for any accumulation tions”...
Page 550 548 SERVICING AND MAINTENANCE • Mix a minimum solution of 50% OAT engine coolant CAUTION! (Continued) that meets the requirements of FCA Material Standard be compatible with the radiator engine coolant and MS.90032 and distilled water. Use higher concentrations may plug the radiator. (not to exceed 70%) if temperatures below −34°F (−37°C) •...
Page 551 SERVICING AND MAINTENANCE 549 HOAT and OAT coolant are mixed in an emergency, Disposal Of Used Coolant have a authorized dealer drain, flush, and refill with Used ethylene glycol-based coolant (antifreeze) is a regu- OAT coolant (conforming to MS.90032) as soon as pos- lated substance requiring proper disposal.
Page 552 550 SERVICING AND MAINTENANCE To check the coolant level: 1. Open the coolant reservoir. Coolant Reservoir Dipstick 3. Check the coolant level on the dipstick. The radiator normally remains completely full, so there is Opening The Coolant Reservoir no need to remove the radiator cap unless checking for 2.
Page 553 SERVICING AND MAINTENANCE 551 Checking Coolant Level — 6.4L Engine If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be The level of the coolant in the pressurized coolant bottle safely driven. The vapor will soon dissipate. should be between the “MIN”...
Page 554: Brake System
552 SERVICING AND MAINTENANCE the correct type thermostat. Other designs may result in “MAX” mark and a “MIN” mark. The fluid level must be unsatisfactory engine coolant (antifreeze) performance, kept within these two marks. Do not add fluid above the poor gas mileage, and increased emissions.
Page 555: Automatic Transmission
SERVICING AND MAINTENANCE 553 is important to maintain the transmission fluid at the WARNING! (Continued) correct level using the recommended fluid. No chemical in a tightly closed container. Keep the master cylin- flushes should be used in any transmission; only the der reservoir cap secured at all times.
Page 556 554 SERVICING AND MAINTENANCE CAUTION! CAUTION! (Continued) may occur. Your authorized dealer has the proper tools Do not use chemical flushes in your transmission as to adjust the fluid level accurately. the chemicals can damage your transmission compo- nents. Such damage is not covered by the New Vehicle Fluid Level Check —...
Page 557 SERVICING AND MAINTENANCE 555 3. Run the engine at normal idle speed for at least 60 the dipstick tube, wait a minimum of two minutes for seconds, and leave the engine running for the rest of this the oil to fully drain into the transmission before re- procedure.
Page 558: Rear Axle And 4X4 Front Driving Axle Fluid Level
556 SERVICING AND MAINTENANCE Rear Axle And 4x4 Front Driving Axle Fluid Level NOTE: To prevent dirt and water from entering the transmission after checking or replenishing fluid, make For normal service, periodic fluid level checks are not sure that the dipstick cap is properly reseated. It is normal required.
Page 559: Transfer Case
SERVICING AND MAINTENANCE 557 Transfer Case NOTE: The presence of water in the gear lubricant will result in corrosion and possible failure of differential Selection Of Lubricant components. Operation of the vehicle in water, as may be Use only the manufacturer’s recommended fluid. Refer to encountered in some off-highway types of service, will “Fluids And Lubricants”...
Page 560: Hoisting
558 SERVICING AND MAINTENANCE HOISTING Tire Markings A conventional floor jack may be used at the jacking locations. Refer to the graphics that show jacking locations. However, a floor jack or frame hoist must never be used on any other parts of the underbody. CAUTION! Never use a floor jack directly under the differential housing of a loaded truck or damage to your vehicle...
Page 561 SERVICING AND MAINTENANCE 559 NOTE: • Temporary spare tires are designed for temporary emer- gency use only. Temporary high pressure compact spare • P (Passenger) — Metric tire sizing is based on U.S. tires have the letter “T” or “S” molded into the sidewall design standards.
Page 562 560 SERVICING AND MAINTENANCE Tire Sizing Chart EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on U.S. design standards, or ..blank..= Passenger car tire based on European design standards, or LT = Light truck tire based on U.S.
Page 563 SERVICING AND MAINTENANCE 561 EXAMPLE: Service Description: 95 = Load Index – A numerical code associated with the maximum load a tire can carry H = Speed Symbol – A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under cer- tain operating conditions –...
Page 564 562 SERVICING AND MAINTENANCE Tire Identification Number (TIN) the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the The TIN may be found on one or both sides of the tire; outboard side, then you will find it on the inboard side of however, the date code may only be on one side.
Page 565 SERVICING AND MAINTENANCE 563 Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located be- hind the front door. Cold tire inflation pressure is defined as the tire pressure after the Cold Tire Inflation Pressure vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours.
Page 566 564 SERVICING AND MAINTENANCE Tire Loading And Tire Pressure NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Check the inflation pressure of each tire, including the spare tire (if equipped), at least monthly and inflate to the recommended pressure for your vehicle.
Page 567 SERVICING AND MAINTENANCE 565 Tire And Loading Information Placard Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard in “Vehicle Loading”...
Page 568 566 SERVICING AND MAINTENANCE Steps For Determining Correct Load Limit— this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. (1) Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or Metric Example For Load Limit XXX lbs.”...
Page 569 SERVICING AND MAINTENANCE 567 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the rec- ommended load capacity for your vehicle. Never over- load them.
Page 570: Tires - General Information
568 SERVICING AND MAINTENANCE Tires — General Information WARNING! (Continued) Tire Pressure • Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of Proper tire inflation pressure is essential to the safe and vehicle control. satisfactory operation of your vehicle.
Page 571 SERVICING AND MAINTENANCE 569 Fuel Economy CAUTION! Underinflated tires will increase tire rolling resistance After inspecting or adjusting the tire pressure, always resulting in higher fuel consumption. reinstall the valve stem cap. This will prevent moisture Tread Wear and dirt from entering the valve stem, which could damage the valve stem.
Page 572 570 SERVICING AND MAINTENANCE pressure should be increased by 3 psi (21 kPa), which Radial Ply Tires equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition. WARNING! Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) Combining radial ply tires with other types of tires on during operation.
Page 573 SERVICING AND MAINTENANCE 571 Run Flat Tires — If Equipped Tire Spinning Run Flat tires allow you the capability to drive 50 miles When stuck in mud, sand, snow, or ice conditions, do not (80 km) at 50 mph (80 km/h) after a rapid loss of inflation spin your vehicle’s wheels above 30 mph (48 km/h) or for pressure.
Page 574 572 SERVICING AND MAINTENANCE Tread Wear Indicators worn to the tread wear indicators, the tire should be replaced. Refer to “Replacement Tires” in this section for Tread wear indicators are in the original equipment tires to further information. help you in determining when your tires should be re- placed.
Page 575 SERVICING AND MAINTENANCE 573 It is recommended to replace the two front tires or two rear WARNING! (Continued) tires as a pair. Replacing just one tire can seriously affect You could lose control and have a collision resulting in your vehicle’s handling. If you ever replace a wheel, make serious injury or death.
Page 576: Tire Types
574 SERVICING AND MAINTENANCE Summer Or Three Season Tires — If Equipped WARNING! (Continued) Summer tires provide traction in both wet and dry condi- • Never use a tire with a smaller load index or capacity, tions, and are not intended to be driven in snow or on ice. other than what was originally equipped on your If your vehicle is equipped with Summer tires, be aware vehicle.
Page 577: Spare Tires - If Equipped
SERVICING AND MAINTENANCE 575 Spare Tires — If Equipped Snow Tires Some areas of the country require the use of snow tires NOTE: For vehicles equipped with Tire Service Kit instead during the Winter. Snow tires can be identified by a of a spare tire, please refer to “Tire Service Kit”...
Page 578 576 SERVICING AND MAINTENANCE spare by looking at the spare tire description on the Tire WARNING! (Continued) and Loading Information Placard located on the driver’s needs to be replaced. Be sure to follow the warnings, side door opening or on the sidewall of the tire. Compact which apply to your spare.
Page 579 SERVICING AND MAINTENANCE 577 Limited Use Spare — If Equipped WARNING! The limited use spare tire is for temporary emergency use Compact and Collapsible spares are for temporary only. This tire is identified by a label located on the limited emergency use only.
Page 580: Wheel And Wheel Trim Care
578 SERVICING AND MAINTENANCE Wheel And Wheel Trim Care When cleaning extremely dirty wheels including excessive brake dust, care must be taken in the selection of tire and All wheels and wheel trim, especially aluminum and wheel cleaning chemicals and equipment to prevent dam- chrome plated wheels, should be cleaned regularly using age to the wheels.
Page 581: Tire Chains (Traction Devices)
SERVICING AND MAINTENANCE 579 Tire Chains (Traction Devices) Dark Vapor Chrome, Black Satin Chrome, or Low Gloss Clear Coat Wheels Use of traction devices require sufficient tire-to-body clear- ance. Follow these recommendations to guard against CAUTION! damage. If your vehicle is equipped with these specialty •...
Page 582: Tire Rotation Recommendations
580 SERVICING AND MAINTENANCE WARNING! CAUTION! (Continued) • Observe the traction device manufacturer’s instruc- Using tires of different size and type (M+S, Snow) tions on the method of installation, operating speed, between front and rear axles can cause unpredictable and conditions for use. Always use the suggested handling.
Page 583 SERVICING AND MAINTENANCE 581 The suggested rotation method is the “rearward cross” Directional Tires — If Equipped shown in the following diagram. This rotation pattern does For the R/T package with 22” tires and wheels, the not apply to some directional tires that must not be rotational direction of the tire must be taken into consid- reversed.
Page 584 582 SERVICING AND MAINTENANCE • After a tire rotation is completed, as shown below, the Dual Rear Wheels — If Equipped system can auto learn the locations of each sensor ID. The tires used on dual wheel assemblies should be Auto learning/localization occurs when the vehicle ig- matched for wear to prevent overloading one tire in a set.
Page 585: Department Of Transportation Uniform Tire Quality Grades
SERVICING AND MAINTENANCE 583 100. The relative performance of tires depends upon the CAUTION! (Continued) actual conditions of their use, however, and may depart the truck. For example, if the spare is used to replace significantly from the norm due to variations in driving an outer rear tire it will have to be remounted on the habits, service practices, and differences in road charac- rim so that the wheel is dished inward.
Page 586: Storing The Vehicle
584 SERVICING AND MAINTENANCE • Any time you store your vehicle or keep it out of service Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive (i.e., vacation) for two weeks or more, run the air condi- temperature can lead to sudden tire failure.
Page 587: Body And Underbody Maintenance
SERVICING AND MAINTENANCE 585 What Causes Corrosion? Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses. Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. Tri-Fold Soft Tonneau Cover Care The most common causes are: For cleaning and protecting the vinyl Tri-Fold Tonneau...
Page 588 586 SERVICING AND MAINTENANCE • If you carry special cargo such as chemicals, fertilizers, CAUTION! de-icer salt, etc., be sure that such materials are well packaged and sealed. • Do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch •...
Page 589: Interiors
SERVICING AND MAINTENANCE 587 To Help Maintain The Appearance Of Your Spray-On Repairing The Spray-On Bedliner Bedliner, Follow The Steps Below: While extremely tough, it is possible to damage a Spray-On 1. Rinse your truck bed out with water to remove any Bedliner.
Page 590: Plastic And Coated Parts
588 SERVICING AND MAINTENANCE Stain Repel Fabric Cleaning Procedure — If Replace the belts if they appear frayed or worn or if the Equipped buckles do not work properly. Stain Repel seats may be cleaned in the following manner: NOTE: If the belts retract slowly, inspect the upper turning loop for soiling.
Page 591: Leather Parts
SERVICING AND MAINTENANCE 589 act as an abrasive and damage the leather upholstery and CAUTION! (Continued) should be removed promptly with a damp cloth. Stubborn painted, or decorated surfaces of the interior may soils can be removed easily with a soft cloth and Mopar causepermanent damage.
Page 592: Glass Surfaces
590 SERVICING AND MAINTENANCE Glass Surfaces All glass surfaces should be cleaned on a regular basis with Mopar Glass Cleaner, or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear window equipped with electric defrosters or windows equipped with radio antennas.
Page 593 TECHNICAL SPECIFICATIONS CONTENTS IDENTIFICATION DATA....593 ▫ Do Not Use E-85 In Non-Flex Fuel Vehicles ..598 ▫ Vehicle Identification Number ... . .593 ▫...
Page 594 592 TECHNICAL SPECIFICATIONS ▫ Maintenance ......602 ▫ Engine ......604 FLUID CAPACITIES .
Page 595: Identification Data
TECHNICAL SPECIFICATIONS 593 IDENTIFICATION DATA BRAKE SYSTEM If power assist is lost for any reason (for example, repeated Vehicle Identification Number brake applications with the engine off), the brakes will still The Vehicle Identification Number (VIN) is found on the function.
Page 596: Wheel And Tire Torque Specifications
594 TECHNICAL SPECIFICATIONS WHEEL AND TIRE TORQUE SPECIFICATIONS NOTE: Dual wheels are flat mounted, center piloted. The lug nuts are a two-piece assembly. When the tires are being Proper lug nut/bolt torque is very important to ensure that rotated or replaced, clean these lug nuts and add two drops the wheel is properly mounted to the vehicle.
Page 597 TECHNICAL SPECIFICATIONS 595 Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles. Four And Five Lug Nuts/Bolts Torque Pattern WARNING! To avoid the risk of forcing the vehicle off the jack, do Wheel Mounting Surface not tighten the lug nuts fully until the vehicle has been Tighten the lug nuts/bolts in a star pattern until each...
Page 598: Fuel Requirements
596 TECHNICAL SPECIFICATIONS FUEL REQUIREMENTS 5.7L Engine Do not use E-85 flex fuel or ethanol blends greater than 3.6L Engine 15% in this engine. This engine is designed to meet all emis- This engine is designed to meet all emis- sions regulations and provide satisfac- sions regulations and provide excellent tory fuel economy and performance...
Page 599: 6.4L Engine
TECHNICAL SPECIFICATIONS 597 6.4L Engine Reformulated Gasoline Do not use E-85 flex fuel or ethanol blends greater than Many areas of the country require the use of cleaner 15% in this engine. burning gasoline referred to as “Reformulated Gasoline”. Reformulated gasoline contains oxygenates and are specifi- This engines is designed to meet all cally blended to reduce vehicle emissions and improve air emissions regulations and provide satis-...
Page 600: Gasoline/Oxygenate Blends
598 TECHNICAL SPECIFICATIONS gasoline is recommended. Visit www.toptiergas.com for a Problems that result from using gasoline containing more list of TOP TIER Detergent Gasoline Retailers. than 15% ethanol (E-15) or gasoline containing methanol are not the responsibility of the manufacturer and may Indiscriminate use of fuel system cleaning agents should be void or not be covered under New Vehicle Limited War- avoided.
Page 601: Cng And Lp Fuel System Modifications
TECHNICAL SPECIFICATIONS 599 CNG And LP Fuel System Modifications Fuel System Cautions Modifications that allow the engine to run on compressed CAUTION! natural gas (CNG) or liquid propane (LP) may result in damage to the engine, emissions, and fuel system compo- Follow these guidelines to maintain your vehicle’s nents.
Page 602: Carbon Monoxide Warnings
600 TECHNICAL SPECIFICATIONS FLEXIBLE FUEL (3.6L ENGINE ONLY) NOTE: Intentional tampering with the emissions control system can result in civil penalties being assessed against E-85 General Information you. The information in this section is unique for Flexible Fuel Carbon Monoxide Warnings vehicles only.
Page 603: Fuel Requirements
TECHNICAL SPECIFICATIONS 601 NOTE: WARNING! (Continued) • Use seasonally adjusted E-85 fuel (ASTM D5798). With materials lit or products that can cause spark in or near non-seasonally adjusted E-85 fuel, hard starting and the vehicle when removing the fuel filler tube cap (gas rough idle following start up may be experienced even if cap) or filling the tank.
Page 604: Starting
602 TECHNICAL SPECIFICATIONS Starting Replacement Parts The characteristics of E-85 fuel make it unsuitable for use All fuel and engine components in your Flexible Fuel when ambient temperatures fall below 0°F (-18°C). In the Vehicle (FFV) are designed to be compatible with ethanol. range of 0°F (-18°C) to 32°F (0°C), an increase in the time it Ethanol compatible service components are required.
Page 605: Fluid Capacities
TECHNICAL SPECIFICATIONS 603 FLUID CAPACITIES U.S. Metric Fuel (Approximate) 1500 Regular Cab Shortbed/Crew Quad Cab Models 26 Gallons 98 Liters 1500 Regular Cab Longbed/Crew Quad Cab Models (Optional) 32 Gallons 121 Liters 2500/3500 Shortbed Models 31 Gallons 117 Liters 2500/3500 Longbed Models 32 Gallons 121 Liters Engine Oil With Filter...
Page 606: Engine
604 TECHNICAL SPECIFICATIONS U.S. Metric 5.7L Engine – 2500/3500 Models (We recommend you use Mopar 18.3 Quarts 17.3 Liters Antifreeze/Coolant 10 Year/150,000 Mile Formula that meets the re- quirements of FCA Material Standard MS.90032.) 6.4 Liter Engine – 2500/3500 Models (We recommend you use Mopar 16.6 Quarts 15.7 Liters Antifreeze/Coolant 10 Year/150,000 Mile Formula that meets the re-...
Page 607 TECHNICAL SPECIFICATIONS 605 Component Fluid, Lubricant, or Genuine Part Engine Oil – 5.7L Engine We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the requirements of FCA Material Standard MS-6395 such as Mopar, Pennzoil, and Shell Helix. Refer to your engine oil filler cap for correct SAE grade.
Page 608 606 TECHNICAL SPECIFICATIONS CAUTION! CAUTION! (Continued) • Do not use water alone or alcohol-based engine • Mixing of engine coolant (antifreeze) other than coolant (antifreeze) products. Do not use additional specified Organic Additive Technology (OAT) en- rust inhibitors or antirust products, as they may not gine coolant (antifreeze), may result in engine dam- be compatible with the radiator engine coolant and age and may decrease corrosion protection.
Page 609: Chassis
TECHNICAL SPECIFICATIONS 607 Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission – Eight-Speed Automatic Use only Mopar ZF 8&9 Speed ATF Automatic Transmis- sion Fluid, or equivalent. Failure to use the correct fluid may affect the function or performance of your transmis- sion.
Page 610 608 TECHNICAL SPECIFICATIONS Component Fluid, Lubricant, or Genuine Part Front and Rear Axle – 2500/3500 Models We recommend you use SAE 75W-85 HD Ram GL-5 Synthetic Axle Lubricant. Limited slip additive is not required for Limited-Slip Rear Axles. Brake Master Cylinder We recommend you use Mopar DOT 3.
Page 611 MULTIMEDIA CONTENTS UCONNECT RADIOS ....611 RADIO OPERATION AND MOBILE PHONES . . .654 PERSONALIZED MENU BAR ....611 ▫...
Page 612 610 MULTIMEDIA ▫ Register (4C NAV) ..... .668 ▫ General Information .....672 ▫...
Page 613: Uconnect Radios
MULTIMEDIA UCONNECT RADIOS For detailed information about your Uconnect radio, refer to your Uconnect Owner’s Manual Supplement. NOTE: Uconnect screen images are for illustration pur- poses only and may not reflect exact software for your vehicle. PERSONALIZED MENU BAR The Uconnect features and services in the main menu bar are easily changed for your convenience.
Page 614: Cybersecurity
612 MULTIMEDIA CYBERSECURITY WARNING! Your vehicle may be a connected vehicle and may be • It is not possible to know or to predict all of the equipped with both wired and wireless networks. These possible outcomes if your vehicle’s systems are networks allow your vehicle to send and receive informa- breached.
Page 615: Uconnect Settings
MULTIMEDIA UCONNECT SETTINGS NOTE: • FCA US LLC or your dealer may contact you directly The Uconnect system uses a combination of buttons on the regarding software updates. touchscreen and buttons on the faceplate located on the center of the instrument panel that allows you to access •...
Page 616 614 MULTIMEDIA Uconnect 3 Buttons On The Touchscreen And Buttons On Uconnect 4C/4C NAV Buttons On The Touchscreen And The Faceplate Buttons On The Faceplate 1 — Uconnect Buttons On The Touchscreen 1 — Uconnect Buttons On The Touchscreen 2 — Uconnect Buttons On The Faceplate 2 —...
Page 617: Customer Programmable Features - Uconnect 3
MULTIMEDIA Customer Programmable Features — Uconnect 3 mode the Uconnect system allows you to access program- Personal Settings mable features that may be equipped such as Display, Units, Voice, Clock, Safety & Driving Assistance, Lights, Doors & Locks, Auto-On Comfort (if equipped), Engine Off Options, Suspension, Trailer Brake, Audio, Compass Set- tings, Phone/Bluetooth, SiriusXM Setup (if equipped), Restore Settings, Clear Personal Data and System Informa-...
Page 618 616 MULTIMEDIA Display After pressing the “Display” button on the touchscreen, the following settings will be available. Setting Name Selectable Options Display Mode Auto Manual Set Language English, Français, Español Touchscreen Beep Fuel Saver Display NOTE: The “Fuel Saver Display” feature will allow you to enable fuel saver mode and will be displayed in the instrument cluster display.
Page 619 MULTIMEDIA Voice After pressing the “Voice” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Voice Response Length Brief Detailed Show Command List Always With Help Never Clock & Date After pressing the “Clock & Date” button on the touch- screen, the following settings will be available: Setting Name Selectable Options...
Page 620 618 MULTIMEDIA Safety/Assistance After pressing the “Safety/Assistance” button on the touchscreen, the following settings will be available: Setting Name Selectable Options ParkSense — If Equipped Sound Only Sounds and Display NOTE: The ParkSense system will scan for objects behind the vehicle when the transmission gear selector is in REVERSE and the vehicle speed is less than 7 mph (11 km/h).
Page 621 MULTIMEDIA Setting Name Selectable Options NOTE: Your vehicle may be equipped with the ParkView Rear Back Up Camera Active Guidelines that allows you to see ac- tive guidelines over the ParkView Back up camera display whenever the gear selector is put into REVERSE. The im- age will be displayed on the radio touchscreen display along with a caution note to “check entire surroundings”...
Page 622 620 MULTIMEDIA Setting Name Selectable Options Hill Start Assist — If Equipped NOTE: When the “Hill Start Assist” feature is selected, the Hill Start Assist (HSA) system becomes active. Lights After pressing the “Lights” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Headlight Off Delay...
Page 623 MULTIMEDIA Setting Name Selectable Options Equipped Flash Lights With Lock NOTE: When the “Flash Lights With Lock” feature is selected, the exterior lights will flash when the doors are locked or un- locked with the key fob. This feature may be selected with or without the sound horn on lock feature selected. Doors &...
Page 624 622 MULTIMEDIA Setting Name Selectable Options Sound Horn With Lock 1st Press 2nd Press Remote Door Unlock Driver NOTE: The “Remote Door Unlock” feature will allow you to program your remote door locks to open “All doors” or only the “Driver door” with the first push of the key fob or grabbing the Passive Entry door handle. Sound Horn With Remote Start NOTE:...
Page 625 MULTIMEDIA Setting Name Selectable Options NOTE: The “Passive Entry” feature allows you to lock and unlock the vehicle’s door(s) without having to push the key fob lock or unlock buttons. It automatically unlocks the doors when the outside door handle is grabbed. Flash Lights With Lock NOTE: When the “Flash Lights With Lock”...
Page 626 624 MULTIMEDIA Engine Off Options After pressing the “Engine Off Options” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Easy Exit Seats — If Equipped Headlight Off Delay 0 sec 30 sec 60 sec 90 sec Engine Off Power 0 sec...
Page 627 MULTIMEDIA Setting Name Selectable Options Auto Entry/Exit Suspension NOTE: When the “Auto Entry/Exit Suspension” feature is selected, the vehicle automatically lowers from ride height posi- tion when vehicle shifted to park for easy entry/exit. Display Suspension Messages Warning Only Automatic Aero Mode (1500 Model Only) NOTE: When the “Automatic Aero Mode”...
Page 628 626 MULTIMEDIA Setting Name Selectable Options Wheel Alignment Mode NOTE: The “Wheel Alignment Mode” feature prevents auto leveling of the air suspension while performing a wheel align- ment service. Before performing a wheel alignment, this mode must be enabled. Refer to your authorized dealer for further information.
Page 629 MULTIMEDIA Setting Name Selectable Options NOTE: The “Balance/Fade” feature allows you to adjust the Balance and Fade settings. Press and drag the speaker icon or use the arrows to adjust, tap the “C” icon to readjust to the center. Equalizer –...
Page 630 628 MULTIMEDIA Setting Name Selectable Options Loudness — If Equipped NOTE: The “Loudness” feature improves sound quality at lower volumes. Compass Settings — If Equipped After pressing the “Compass Settings” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Variance...
Page 631 MULTIMEDIA Setting Name Selectable Options Perform Compass Calibration NOTE: Press the “Calibration” button on the touchscreen to change this setting. This compass is self-calibrating, which eliminates the need to manually reset the compass. When the vehicle is new, the compass may appear erratic until it is calibrated.
Page 632 630 MULTIMEDIA Phone/Bluetooth After pressing the “Phone/Bluetooth” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Paired Phones List of Paired Phones NOTE: The “Paired Phones” feature shows which phones are paired to the Phone/Bluetooth system. For further information, refer to the Uconnect Owner’s Manual Supplement.
Page 633 MULTIMEDIA Setting Name Selectable Options Subscription Info Sirius ID NOTE: New vehicle purchasers or lessees will receive a free limited time subscription to SiriusXM Satellite Radio with your radio. Following the expiration of the free services, it will be necessary to access the information on the Subscription Information screen to re-subscribe.
Page 634 632 MULTIMEDIA Clear Personal Data After pressing the “Clear Personal Data Settings” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Clear Personal Data Cancel NOTE: When this feature is selected it will remove all personal data including Bluetooth devices and presets. If “Yes” is se- lected a pop-up will appear asking Are you sure you want to clear all personal data?”...
Page 635: Customer Programmable Features - Uconnect 4C/4C Nav Personal Settings
MULTIMEDIA Customer Programmable Features — Uconnect to access programmable features that may be equipped 4C/4C NAV Personal Settings such as Display, Voice, Clock, Safety & Driving Assistance, Lights, Doors & Locks, Auto-On Comfort (if equipped), Engine Off Options, Suspension, Trailer Brake, Audio, Phone/Bluetooth, SiriusXM Setup (if equipped), Restore Settings, Clear Personal Data and System Information.
Page 636 634 MULTIMEDIA Display After pressing the “Display” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Display Mode Night Auto NOTE: When Day or Night is selected for the Display Mode, the usage of the Parade Mode feature will cause the radio to activate the Display Brightness Day control even though the headlights are on.
Page 637 MULTIMEDIA Setting Name Selectable Options Set Theme Pre-configured Themes Set Language English, Français, Español Touchscreen Beep Navigation Turn-By-Turn In Cluster — If Equipped Controls Screen Time-Out — If Equipped Fuel Saver Display — If Equipped Units — If Equipped After pressing “Units” on the touchscreen, the following will be available: Setting Name Selectable Options...
Page 638 636 MULTIMEDIA Voice After pressing the “Voice” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Voice Response Length Brief Detailed Show Command List Always With Help Never Clock After pressing the “Clock” button on the touchscreen, the following settings will be available: Setting Name Selectable Options...
Page 639 MULTIMEDIA Safety & Driving Assistance After pressing the “Safety & Driving Assistance” button on the touchscreen, the following settings will be available: Setting Name Selectable Options ParkSense Sound Only Sound and Display NOTE: The Rear Park Assist system will scan for objects behind the vehicle when the transmission gear selector is in RE- VERSE and the vehicle speed is less than 7 mph (11 km/h).
Page 640 638 MULTIMEDIA Setting Name Selectable Options ParkView Backup Camera NOTE: Your vehicle may be equipped with the ParkView Rear Back Up Camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the gear selector is put into REVERSE. The image will be displayed on the radio touchscreen display along with a caution note to “check entire surroundings”...
Page 641 MULTIMEDIA Setting Name Selectable Options Rain Sensing Auto Wipers — If Equipped NOTE: When the “Rain Sensing Auto Wipers” feature is selected, the system will automatically activate the windshield wip- ers if it senses moisture on the windshield. Hill Start Assist — If Equipped Setting Name Selectable Options...
Page 642 640 MULTIMEDIA Lights After pressing the “Lights” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Headlight Off Delay – NOTE: When the “Headlight Off Delay” feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle.
Page 643 MULTIMEDIA Setting Name Selectable Options Auto Dim High Beams — If Equipped NOTE: When the “Auto Dim High Beams” feature is selected, the high beam headlights will deactivate automatically under certain conditions. Flash Lights With Lock NOTE: When the “Flash Lights With Lock” feature is selected, the exterior lamps will flash when the doors are locked or un- locked with the key fob.
Page 644 642 MULTIMEDIA Setting Name Selectable Options Auto Unlock On Exit NOTE: When the “Auto Unlock On Exit” feature is selected, all doors will unlock when the vehicle is stopped and the trans- mission is in the PARK or NEUTRAL position and the driver’s door is opened. Flash Lights With Lock NOTE: When the “Flash Lights With Lock”...
Page 645 MULTIMEDIA Setting Name Selectable Options • If the vehicle is programmed “1st Press Of Key Fob Unlocks: All Doors”, all doors will unlock no matter which Passive Entry equipped door handle is grasped. If “1st Press Of Key Fob Unlocks: Driver Door” is programmed, only the driver’s door will unlock when the driver’s door is grasped.
Page 646 644 MULTIMEDIA Auto Comfort Systems — If Equipped After pressing the “Auto-On Comfort” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Auto-On Driver Heated/ Remote Start All Starts Ventilated Seat & Steering Wheel With Vehicle Start —...
Page 647 MULTIMEDIA Setting Name Selectable Options Engine Off Power Delay – NOTE: When the “Engine Off Power Delay” feature is selected, the power window switches, radio, Uconnect phone system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to ten minutes after the igni- tion is cycled to OFF.
Page 648 646 MULTIMEDIA Setting Name Selectable Options Flash Lights With Lower NOTE: When the “Flash Lights With Lower” feature is selected, the front and rear turn signals will flash when the key fob remote lower button is pressed twice. This feature may be selected with or without the Sound Horn on Lower feature selected.
Page 649 MULTIMEDIA Setting Name Selectable Options Wheel Alignment Mode NOTE: Before performing a wheel alignment, the “Wheel Alignment Mode” must be enabled. Refer to your authorized dealer for further information. Trailer Brake After pressing the “Trailer Brake” button on the touch- screen, the following settings will be available: Setting Name Selectable Options...
Page 650 648 MULTIMEDIA Audio After pressing the “Audio” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Balance/Fade Speaker Icon (Arrow Buttons) NOTE: The “Balance/Fade” feature allows you to adjust the Balance and Fade settings. Press and drag the speaker icon or use the arrows to adjust, tap the “C”...
Page 651 MULTIMEDIA Setting Name Selectable Options AUX Volume Offset — If Equipped NOTE: The “AUX Volume Offset” feature provides the ability to tune the audio level for portable devices connected through the AUX input. Phone Settings After pressing the “Phone Settings” button on the touch- screen, the following settings will be available: Setting Name Selectable Options...
Page 652 650 MULTIMEDIA SiriusXM Setup — If Equipped After pressing the “SiriusXM Setup” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Tune Start NOTE: The “Tune Start” feature begins playing the current song from the beginning when you tune to a music channel using one of the twelve presets, so you can enjoy the complete song.
Page 653 MULTIMEDIA Setting Name Selectable Options Subscription Info Sirius ID NOTE: New vehicle purchasers or lessees will receive a free limited time subscription to SiriusXM Satellite Radio with your radio. Following the expiration of the free services, it will be necessary to access the information on the Subscription Information screen to re-subscribe.
Page 654 652 MULTIMEDIA Clear Personal Data After pressing the “Clear Personal Data” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Clear Personal Data Cancel NOTE: When the “Clear Personal Data” feature is selected it will remove all personal data including Bluetooth devices and presets.
Page 655: Steering Wheel Audio Controls - If Equipped
MULTIMEDIA STEERING WHEEL AUDIO CONTROLS — IF The button located in the center of the right hand control EQUIPPED will switch modes to Radio, CD or other valid audio sources. The remote sound system controls are located on the back surface of the steering wheel.
Page 656: Ipod/Usb/Mp3 Control - If Equipped
654 MULTIMEDIA If you push the switch up or down twice, it plays the second track. If you push the switch up or down three times, it will play the third, etc. IPOD/USB/MP3 CONTROL — IF EQUIPPED Located inside the center console upper lid, this feature allows an iPod or external USB device to be plugged into the USB port.
Page 657: Regulatory And Safety Information
MULTIMEDIA not harmful to the radio. If your radio performance does environments, such as aboard airplanes. If you are unsure not satisfactorily “clear” by the repositioning of the an- of restrictions, you are encouraged to ask for authorization tenna, it is recommended that the radio volume be turned before turning on the wireless radio.
Page 658: Voice Commands
656 MULTIMEDIA VOICE COMMANDS NOTE: • This equipment has been tested and found to comply Introducing Uconnect with the limits for a Class B digital device, pursuant to Start using Uconnect Voice Recognition with these helpful Part 15 of the FCC Rules. These limits are designed to quick tips.
Page 659: Get Started
MULTIMEDIA Uconnect 3 Uconnect 4C/4C NAV Get Started All you need to control your Uconnect system with your voice are the buttons on your steering wheel. 1. Visit UconnectPhone.com to check mobile device and feature compatibility and to find phone pairing instruc- tions.
Page 660 658 MULTIMEDIA 2. Reduce background noise. Wind noise and passenger conversations are examples of noise that may impact recognition. 3. Speak clearly at a normal pace and volume while facing straight ahead. The microphone is located in the head- liner and aimed at the driver. 4.
Page 661: Basic Voice Commands
MULTIMEDIA Basic Voice Commands The basic Voice Commands below can be given at any point while using your Uconnect system. Push the VR button . After the beep, say: • “Cancel” to stop a current voice session • “Help” to hear a list of suggested Voice Commands •...
Page 662: Radio
660 MULTIMEDIA TIP: At any time, if you are not sure of what to say or want to learn a Voice Command, push the VR button and say “Help.” The system will provide you with a list of commands. Uconnect 4C/4C NAV Radio Uconnect 3.0 Use your voice to quickly get to the AM, FM or SiriusXM...
Page 663: Media
MULTIMEDIA Uconnect 3 Uconnect 4C/4C NAV Media Uconnect offers connections via USB, Bluetooth and auxil- iary ports (If Equipped). Voice operation is only available for connected USB and AUX devices. (Remote CD player optional and not available on all vehicles.)
Page 664 662 MULTIMEDIA Push the VR button . After the beep, say one of the following commands and follow the prompts to switch your media source or choose an artist. • “ Change source to Bluetooth” • “ Change source to AUX” •...
Page 665: Phone
MULTIMEDIA Uconnect 3 Uconnect 4C/4C NAV Phone Making and answering hands-free phone calls is easy with Uconnect. When the Phonebook button is illuminated on your touchscreen, your system ready. Check UconnectPhone.com for mobile phone compatibility and pairing instructions.
Page 666 664 MULTIMEDIA Push the Phone button . After the beep, say one of the following commands: • “ Call John Smith” • “ Dial 123-456-7890 and follow the system prompts” • “ Redial (call previous outgoing phone number)” • “ Call back (call previous incoming phone number)” TIP: When providing a Voice Command, push the Phone button and say “Call,”...
Page 667: Climate (4C/4C Nav)
MULTIMEDIA Uconnect 3 Uconnect 4C/4C NAV Phone Climate (4C/4C NAV) Too hot? Too cold? Adjust vehicle temperatures hands-free and keep everyone comfortable while you keep moving ahead. (If vehicle is equipped with climate control.) Push the VR button . After the beep, say one of the following commands: •...
Page 668: Navigation (4C Nav)
666 MULTIMEDIA • “ Set passenger temperature to 70 degrees” Navigation (4C NAV) The Uconnect navigation feature helps you save time and TIP: Voice Command for Climate may only be used to become more productive when you do not know exactly adjust the interior temperature of your vehicle.
Page 669: Siriusxm Guardian (4C Nav) - If Equipped
MULTIMEDIA NOTE: Your vehicle may be transmitting data as autho- rized by the subscriber. An included trial and/or subscription is required to take advantage of the SiriusXM Guardian services in the next section of this guide. To register with SiriusXM Guardian, press the Apps button on the 8.4-inch touchscreen to get started.
Page 670: Register (4C Nav)
668 MULTIMEDIA Mobile App (4C NAV) Vehicle Health Reports** Vehicle Health Alert** You’re only a few steps away from using remote com- mands and playing your favorite music in your car. Performance Pages Plus** **If vehicle is equipped. Register (4C NAV) To unlock the full potential of SiriusXM Guardian in your vehicle, you must activate your SiriusXM Guardian ser- vices.
Page 671: Siriusxm Travel Link (4C Nav)
MULTIMEDIA • Press the Location button on the navigation bar at the bottom of the app to bring up a map to locate your vehicle or send a location to your vehicle’s navigation system. • Press the Settings button in the upper left corner of the app to bring up app settings and access the Assist Call Centers.
Page 672 670 MULTIMEDIA “Phone” icon on the main menu bar to begin Apple CarPlay. Press and hold the VR button on the steering wheel, or press and hold the “Home” button within Apple CarPlay, to activate Siri, which recognizes natural voice commands to use a list of your iPhone’s features: •...
Page 673: Android Auto - If Equipped
MULTIMEDIA Android Auto — If Equipped Android Auto allows you to use your voice to interact with Android’s best-in-class speech technology through your vehicle’s voice recognition system, and use your smart- phone’s data plan to project your Android powered smart- phone and a number of its apps onto your Uconnect touchscreen.
Page 674 672 MULTIMEDIA General Information Additional Information The following regulatory statement applies to all Radio © 2017 FCA US LLC. All rights reserved. Mopar and Frequency (RF) devices equipped in this vehicle: Uconnect are registered trademarks and Mopar Owner Connect is a trademark of FCA US LLC. Android is a This device complies with Part 15 of the FCC Rules and trademark of Google Inc.
Page 675 MULTIMEDIA CD/DVD DISC MAINTENANCE 6. Do not expose the disc to direct sunlight. To keep a CD/DVD in good condition, take the following 7. Do not store the disc where temperatures may become precautions: too high. 1. Handle the disc by its edge; avoid touching the surface. NOTE: If you experience difficulty in playing a particular disc, it may be damaged, (e.g., scratched, reflective coating 2.
Page 677 CUSTOMER ASSISTANCE CONTENTS SUGGESTIONS FOR OBTAINING SERVICE FOR ▫ Customer Assistance For The Hearing Or Speech YOUR VEHICLE ......676 Impaired (TDD/TTY) .
Page 678: Suggestions For Obtaining Service For Your Vehicle
676 CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR IF YOU NEED ASSISTANCE YOUR VEHICLE The manufacturer and its authorized dealer are vitally interested in your satisfaction. We want you to be happy Prepare For The Appointment with our products and services. If you are having warranty work done, be sure to have the right papers with you.
Page 679: Fca Us Llc Customer Center
CUSTOMER ASSISTANCE 677 In Mexico Contact Any communication to the manufacturer’s customer center should include the following information: Av. Prolongacion Paseo de la Reforma, 1240 • Owner’s name and address Sante Fe C.P. 05109 • Owner’s telephone number (home and office) Mexico, D.
Page 680: Service Contract
678 CUSTOMER ASSISTANCE to a TDD or a conventional teletypewriter (TTY) in the responsible for any service contract other than the manufac- turer’s service contract. If you purchased a service contract United States, can communicate with the manufacturer by that is not a manufacturer’s service contract, and you require dialing 1-800-380-CHRY.
Page 681: Warranty Information
CUSTOMER ASSISTANCE 679 WARRANTY INFORMATION campaign. However, NHTSA cannot become involved in individual problems between you, your authorized See the Warranty Information Booklet for the terms and dealer or FCA US LLC. provisions of FCA US LLC warranties applicable to this vehicle and market.
Page 682 680 CUSTOMER ASSISTANCE Service Manuals Owner’s Manuals These comprehensive Service Manuals provide the infor- These Owner’s Manuals have been prepared with the mation that students and professional technicians need in assistance of service and engineering specialists to acquaint diagnosing/troubleshooting, problem solving, maintain- you with specific FCA US LLC vehicles.
Page 683 INDEX...
Page 684 682 INDEX Adding Engine Coolant (Antifreeze) ... . .548 Air Conditioning Refrigerant ....533, 534 Adding Fuel ......413 Air Conditioning System .
Page 685 INDEX 683 Fluid Level Check .....553, 554 Warning Light ......190 Fluid Type .
Page 686 684 INDEX Child Restraint ......252 Coolant Level ....546, 549, 551 Child Restraints Disposal Of Used Coolant .
Page 687 INDEX 685 Disposal Emergency Brake......295 Antifreeze (Engine Coolant) ....549 Emergency, In Case Of Door Ajar .
Page 688 686 INDEX Starting .......289 Replacement Parts ......602 Engine Oil Viscosity .
Page 689 INDEX 687 Materials Added ......597 Hazard Warning Flasher..... .447 Methanol .
Page 690 688 INDEX Ignition Key Removal ......28 Passive Entry ......39 Illuminated Entry .
Page 691 INDEX 689 Daytime Running ......74 Limited-Slip Differential ....375, 557 Engine Temperature Warning .
Page 692 690 INDEX Memory Seats And Radio .....44 Disposal .......530 Methanol .
Page 693 INDEX 691 Passive Entry ......39 Pretensioners Pedals, Adjustable ......62 Seat Belts .
Page 694 692 INDEX Programming Additional Key Fobs ..27, 34 Lap/Shoulder Belt Operation ....227 Remote Sound System (Radio) Controls ...653 Lap/Shoulder Belt Untwisting .
Page 695 INDEX 693 Memory ......44, 49 Shift Lever Override ......506 Power .
Page 696 694 INDEX Steering Wheel Audio Controls ....653 Compact Spare ......575 Steering Wheel Mounted Sound System Controls .
Page 697 INDEX 695 Tonneau Cover ......585 Transfer Case ......557 Tonneau Cover Cleaning .
Page 698 696 INDEX Universal Garage Door Opener (HomeLink) Wheel And Wheel Trim ..... .578 Programming HomeLink ... . .115, 117, 118 Wheel And Wheel Trim Care .
Page 699 INSTALLATION OF RADIO TRANSMITTING The antenna cable should be as short as practical and EQUIPMENT routed away from the vehicle wiring when possible. Use Special design considerations are incorporated into this only fully shielded coaxial cable. vehicle’s electronic system to provide immunity to radio Carefully match the antenna and cable to the radio to frequency signals.
Page 700 STICK WITH THE SPECIALISTS ® 18DS-126-AB ©2017 FCA US LLC. All Rights Reserved. SECOND Edition Ram is a registered trademark of FCA US LLC. Printed in the U.S.A.

This manual is also suitable for:

1500 2018 2500 2018

Save PDF