Tip Start Feature; Keyless Enter 'N Go™ - Ignition; Normal Starting Using Engine Start/Stop Button - RAM 1500 2025 Owner's Manual

If the vehicle is not in PARK and the driver exits
the vehicle with the engine running, the vehicle may
AutoPark.
AutoPark will engage when all of these conditions are
met:
●
Vehicle is equipped with a rotary shifter and an 8-
speed transmission
●
Vehicle is not in PARK
●
Vehicle speed is 1.2 mph (1.9 km/h) or less
●
Driver's seat belt is unbuckled
●
Driver's door is ajar
●
Brake pedal is not pressed
The message "AutoPark Engaged Shift To P Then Shift
To Gear" will display in the instrument cluster.
NOTE:
In some cases the ParkSense graphic will be displayed
in the instrument cluster, causing the "AutoPark
Engaged Shift To P Then Shift To Gear" message to
not be seen. In these cases, the gear selector must be
returned to "P" to select desired gear.
If the driver shifts into PARK while moving, the vehicle
may AutoPark.
AutoPark will engage ONLY when vehicle speed is 1.2
mph (1.9 km/h) or less.
The message "Vehicle Speed Is Too High To Shift to
P" will be displayed in the instrument cluster if vehicle
speed is above 1.2 mph (1.9 km/h).
WARNING!
If vehicle speed is above 1.2 mph (1.9 km/h), the
transmission will default to NEUTRAL until the vehicle
speed drops below 1.2 mph (1.9 km/h). A vehicle
left in the NEUTRAL position can roll. As an added
precaution, always apply the parking brake when
exiting the vehicle.
4WD LOW — If Equipped
AutoPark will be disabled when operating the vehicle in
4WD LOW.
The message "AutoPark Disabled" will be displayed in
the instrument cluster.
Additional customer warnings will be given when all of
these conditions are met:
●
Vehicle is not in PARK
●
Driver's door is ajar
●
Vehicle is in 4WD LOW
The message "AutoPark Not Engaged" will be displayed
in the instrument cluster. A warning chime will continue
until you shift the vehicle into PARK or the driver's door
is closed.
ALWAYS DO A VISUAL CHECK that your vehicle is in
PARK by looking for the "P" in the instrument cluster
display and near the gear selector. As an added
precaution, always apply the parking brake when exiting
the vehicle.
T S F
IP TART EATURE
Do not press the accelerator. Cycle the ignition switch
briefly to the START position and release it. The
STARTING AND OPERATING
starter motor will continue to run and will automatically
disengage when the engine is running.
K E ' G ™ — I
EYLESS NTER N O GNITION
This feature allows the driver to operate the ignition
switch with the push of a button, as long as the Remote
Start/Keyless Enter 'n Go™ key fob is in the passenger
compartment.
N S U ENGINE
ORMAL TARTING SING
START/STOP B
UTTON
To Turn On The Engine Using The ENGINE START/STOP
Button
1. The transmission must be in PARK.
2. Press and hold the brake pedal while pushing the
ENGINE START/STOP button once.
3. The system starts the vehicle. If the vehicle fails to
start, the starter will disengage automatically after
10 seconds.
4. If you wish to stop the cranking of the engine prior
to the engine starting, push the button again.
To Turn Off The Engine Using The ENGINE START/STOP
Button
1. Place the gear selector in PARK, then push
and release the ENGINE START/STOP button. The
ignition will return to the OFF position.
2. If the gear selector is not in PARK, the ENGINE
START/STOP button must be held for two seconds
or three short pushes in a row with the vehicle
speed above 5 mph (8 km/h) before the engine
will shut off. The ignition will remain on until the
123
4